Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR (for M15A-FKS) › 2020.08–2021.07
RM3700E _58 Vehicle Interior _093020 HEATING / AIR CONDITIONING _0438493 COMPRESSOR(for M15A-FKS) A

HEATING / AIR CONDITIONING  COMPRESSOR(for M15A-FKS)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
I116870N02
1,0.448 1.99,0.615 0.99,0.167 1.688,2.469 2.417,2.635 0.729,0.167 0.917,4.375 1.958,4.542 1.042,0.167 0.344,2.094 1.333,2.26 0.99,0.167 6.438,0.271 6.771,0.271 false 1.885,3.677 1.885,4.01 false 0.906,1.281 1.292,1.281 false 2.51,1.188 2.51,1.375 false 3.594,1.792 3.927,1.792 false 4.396,0.802 4.729,0.802 false 3.052,1.26 3.385,1.26 false 1.969,1.844 1.969,2.177 true 0.823,2.094 0.823,1.906 0.823,1.906 1.25,1.833 false 1.99,0.531 2.323,0.531 false 2.417,2.552 2.583,2.552 2.583,2.552 2.75,2.219 false 1.969,4.458 2.302,4.458 false 5.583,0.125 6.448,0.469 0.865,0.344 18 false 1, 7 - 9 2.531,1.375 2.813,1.729 0.281,0.354 18 false 3 0.719,1.156 1,1.51 0.281,0.354 18 false 4 4.792,0.688 5.073,1.042 0.281,0.354 18 false 5 4.26,1.677 4.542,2.031 0.281,0.354 18 false 2 1.281,3.688 1.594,3.885 0.313,0.198 10 false x4 2.427,4.406 2.74,4.604 0.313,0.198 10 false x4 3.5,4.427 3.813,4.625 0.313,0.198 10 false x9 2.813,2.229 3.125,2.427 0.313,0.198 10 false x4 3.427,1.167 3.583,1.365 0.156,0.198 10 false ● 1.938,2.167 2.094,2.365 0.156,0.198 10 false ● 1.823,4.01 2.104,4.365 0.281,0.354 18 false 6 1.052,0.458 2.083,0.677 1.031,0.219 8 false 9.5 (97, 84 in.*lbf) 1.75,2.469 2.729,2.625 0.979,0.156 8 false 25 (255, 18) 1,4.385 2.042,4.594 1.042,0.208 8 false 5.0 (51, 44 in.*lbf) 0.385,2.104 1.417,2.323 1.031,0.219 8 false 9.5 (97, 84 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 ADJUST COMPRESSOR OIL - (Click here) - -
2 COMPRESSOR WITH PULLEY ASSEMBLY 88310 (Click here) - -
3 NO. 1 COOLER REFRIGERANT DISCHARGE HOSE 88711 (Click here) - -
4 SUCTION HOSE SUB-ASSEMBLY 88704 (Click here) - -
5 FAN AND GENERATOR V BELT 16361A - - -
6 NO. 1 ENGINE UNDER COVER ASSEMBLY 51410 - - -
7 AIR CONDITIONING SYSTEM WITH REFRIGERANT - (Click here) - -
8 WARM UP ENGINE - (Click here) - -
9 INSPECT FOR REFRIGERANT LEAK - (Click here) - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part
V100135

Compressor oil ND-OIL 8 or equivalent - -

PROCEDURE

Hide 1.ADJUST COMPRESSOR OIL

a.
I116883C01
1.604,1.99 2.021,1.573 true 4.917,1.688 5.26,1.313 false 4.615,3.5 4.948,3.5 true 2.365,4.156 2.698,4.156 true 0.51,0.146 0.833,0.438 0.323,0.292 18 false i 1.427,1.927 1.74,2.125 0.313,0.198 10 false *a 4.75,1.656 5.063,1.854 0.313,0.198 10 false *b 2.219,4.458 2.531,4.656 0.313,0.198 10 false *c 2.781,4.073 3.094,4.271 0.313,0.198 10 false *e 5.427,3.104 5.74,3.302 0.313,0.198 10 false *d 4.406,3.427 4.719,3.625 0.313,0.198 10 false *e
*a VST Valve (Valve Inside Suction Port) *b Suction Port
*c Down *d Up
*e Pulley - -


i.

When replacing the compressor with pulley assembly with a new one, gradually discharge the inert gas (helium) from the service valve, and drain the following amount of oil before installation.

NOTICE:
·

If a new compressor with pulley assembly is installed without removing the same amount of compressor oil as is remaining in the pipes, the amount of compressor oil will be excessive. This prevents heat exchange in the refrigerant cycle and will cause the air conditioning system to malfunction.

·

A certain amount of compressor oil remains in the compressor with pulley assembly during circulation and the compressor may be damaged if the amount of compressor oil is more/less than this amount. Therefore, make sure to adjust the amount of compressor oil correctly.

·

If the amount of compressor oil remaining in the removed compressor with pulley assembly is excessively low, check for compressor oil leaks.

·

Do not race the engine before replacing the compressor with pulley assembly.

·

Make sure to use ND-OIL 8 or equivalent compressor oil.



1. Remove the suction seal cap.

2. Using a screwdriver with its tip wrapped in protective tape, insert the screwdriver through the suction port and set the VST valve (valve inside suction port) to the open position.

NOTICE:

Be sure not to damage the piping contact surfaces with the tip of the screwdriver.


3. Lightly shake the compressor with pulley assembly with the suction port facing down, and drain the oil (*1).

NOTICE:

Do not allow the pulley to come into contact with the compressor oil.


4. With the pulley facing down, rotate the pulley in the direction shown by the arrow 10 times at a rate of approximately once every 2 seconds (*2).

NOTICE:

If the pulley is rotated, refrigerant or oil might splash out. Thus, keep your face away from the suction port.


5. Rotate the pulley once in the direction shown by the arrow while quickly turning the compressor with pulley assembly so the pulley is up (*3).

6. Proceed with the above procedure (*1) and drain the oil (*4).

7. Drain the oil by repeating the procedures above approximately 5 times (from (*2) to (*4)).

Standard (Amount of Oil to be Removed):
Standard (Amount of Oil to be Removed) Amount of Oil Inside a New Compressor Assembly with Pulley
30 cm3 60 cm3


HINT:

If too much oil has been removed, set the VST valve to the open position through the suction port, and add oil.




Hide 88310 2.INSTALL COMPRESSOR WITH PULLEY ASSEMBLY

a.
I116871N01
0.927,0.083 1.479,0.5 0.552,0.417 18 false i, ii 4.24,0.052 4.521,0.406 0.281,0.354 18 false iii 1.385,0.375 1.542,0.573 0.156,0.198 10 true 1 1.823,1.583 1.979,1.781 0.156,0.198 10 false 2 1.406,1.552 1.563,1.75 0.156,0.198 10 false 3 1.917,0.375 2.073,0.573 0.156,0.198 10 true 4

i.

Temporarily install the compressor with pulley assembly with the 4 bolts.


ii.

Tighten the 4 bolts and install the compressor with pulley assembly in the order shown in the illustration.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


iii.

Connect the connector.



Hide 88711 3.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

a.
I116872N02
2.104,1.979 2.656,2.333 0.552,0.354 18 false iv 0.896,0.073 1.448,0.427 0.552,0.354 18 false i, ii 4.219,0.083 4.771,0.438 0.552,0.354 18 false iii

i.

Remove the vinyl tape from the No. 1 cooler refrigerant discharge hose.


ii.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor with pulley assembly.

Compressor Oil:

ND-OIL 8 or equivalent



iii.

Install the O-ring to the No. 1 cooler refrigerant discharge hose.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



iv.

Connect the No. 1 cooler refrigerant discharge hose to the compressor with pulley assembly with the bolt.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)



Hide 88704 4.CONNECT SUCTION HOSE SUB-ASSEMBLY

a.
I116873N02
2.021,1.917 2.573,2.271 0.552,0.354 18 false iv 0.906,0.094 1.365,0.385 0.458,0.292 18 true i, ii 4.24,0.094 4.792,0.448 0.552,0.354 18 false iii

i.

Remove the vinyl tape from the suction hose sub-assembly.


ii.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor with pulley assembly.

Compressor Oil:

ND-OIL 8 or equivalent



iii.

Install the O-ring to the suction hose sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



iv.

Connect the suction hose sub-assembly to the compressor with pulley assembly with the bolt.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)



Hide 16361A 5.INSTALL FAN AND GENERATOR V BELT

Hide 51410 6.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 7.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT