Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR (for M15A-FXE) › 2020.08–2021.07
RM3700E _58 Vehicle Interior _093020 HEATING / AIR CONDITIONING _0438494 COMPRESSOR(for M15A-FXE) A

HEATING / AIR CONDITIONING  COMPRESSOR(for M15A-FXE)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
I116878N02
1.625,0.104 2.625,0.271 1,0.167 2.927,4.427 3.927,4.604 1,0.177 1.906,2.469 2.604,2.646 0.698,0.177 0.385,2.031 1.385,2.198 1,0.167 6.448,0.271 6.781,0.271 false 3.833,3.615 3.833,3.948 false 2.625,0.188 2.958,0.188 false 4.427,1.76 4.76,1.76 false 1.458,1.521 1.771,1.25 1.771,1.25 1.958,1.25 false 2.323,1.885 2.656,1.885 false 6.25,1.073 6.583,1.073 false 2.854,0.563 3.042,0.563 3.042,0.563 3.229,0.781 true 3.531,0.49 3.865,0.49 false 2.604,2.552 2.844,2.552 2.844,2.552 3.104,2.229 false 0.875,1.698 0.875,2.031 false 3.938,4.51 4.271,4.51 false 5.573,0.115 6.688,0.458 1.115,0.344 18 false 1, 7 - 9 5.146,1.625 5.427,1.979 0.281,0.354 18 false 2 4.188,0.375 4.51,0.719 0.323,0.344 18 false 3 3.76,3.99 4.042,4.344 0.281,0.354 18 false 5 6.667,0.958 6.948,1.313 0.281,0.354 18 false 6 2.677,0.5 2.833,0.698 0.156,0.198 10 false ● 2.708,1.833 2.865,2.031 0.156,0.198 10 false ● 3.448,2.219 3.76,2.417 0.313,0.198 10 false x4 3.031,3.583 3.375,3.813 0.344,0.229 10 false x4 4.406,4.49 4.781,4.688 0.375,0.198 10 false x4 5.688,4.479 6.031,4.708 0.344,0.229 10 false x9 1.677,0.115 2.656,0.271 0.979,0.156 8 false 9.5 (97, 84 in.*lbf) 1.948,2.479 2.927,2.635 0.979,0.156 8 false 25 (255, 18) 2.281,1.115 2.604,1.458 0.323,0.344 18 false 4 2.99,4.448 3.969,4.604 0.979,0.156 8 false 5.0 (51, 44 in.*lbf) 0.438,2.031 1.417,2.188 0.979,0.156 8 false 9.5 (97, 84 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 ADJUST COMPRESSOR OIL - (Click here) - -
2 COMPRESSOR WITH MOTOR ASSEMBLY 88370 (Click here) - -
3 NO. 1 COOLER REFRIGERANT DISCHARGE HOSE 88711 (Click here) - -
4 SUCTION HOSE SUB-ASSEMBLY 88704 (Click here) - -
5 NO. 1 ENGINE UNDER COVER ASSEMBLY 51410 - - -
6 SERVICE PLUG GRIP G3834 - - -
7 AIR CONDITIONING SYSTEM WITH REFRIGERANT - (Click here) - -
8 WARM UP COMPRESSOR - (Click here) - -
9 INSPECT FOR REFRIGERANT LEAK - (Click here) - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part
V100135

Compressor oil ND-OIL 11 or equivalent - -

PROCEDURE

Hide 1.ADJUST COMPRESSOR OIL

a.
I116879N01
0.51,0.052 0.729,0.333 0.219,0.281 18 false i

i.

When replacing the compressor with motor assembly with a new one, gradually discharge the inert gas from the service valve, and drain the following amount of oil from the new compressor with motor assembly before installation.

Standard:

Drain the oil 30 cc (1.01 fl.oz) from a new compressor with motor assembly.


NOTICE:
·

If a new compressor with motor assembly is installed without removing some oil, there will be too much oil in the system due to the oil remaining in the pipes of the vehicle. Excessive oil in the system prevents heat exchange in the refrigeration cycle and causes ineffective cooling.

·

Be sure to use ND-OIL 11 or equivalent compressor oil. If any compressor oil other than ND-OIL 11 is used, compressor with motor assembly insulation performance may decrease, resulting in leakage of electric power.





Hide 88370 2.INSTALL COMPRESSOR WITH MOTOR ASSEMBLY

a.
I116880C01
5.135,0.188 4.771,0.469 true 1.323,0.792 1.448,0.969 0.125,0.177 10 false 1 1.771,0.802 1.896,0.979 0.125,0.177 10 true 4 1.229,2.063 1.354,2.24 0.125,0.177 10 false 3 1.667,2.156 1.792,2.333 0.125,0.177 10 false 2 5.26,1.365 5.469,1.542 0.208,0.177 10 true *a 5.646,2.344 5.844,2.521 0.198,0.177 10 true *b 1.021,0.063 1.583,0.458 0.563,0.396 18 false i, ii 3.74,0.063 4.385,0.479 0.646,0.417 18 false iv 5.344,2.281 5.542,2.615 0.198,0.333 18 true iii 5.177,0.083 5.49,0.281 0.313,0.198 10 false *c
*a Connector A *b Connector B
*c Green-colored Lock - -
V100135

Slide - -


i.

Temporarily install the compressor with motor assembly with the 4 bolts.


ii.

Tighten the 4 bolts to install the cooler compressor with motor assembly as shown in the illustration.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


iii.

Connect the connector B.


iv.

Remove the protective tape wrapped around connector A, and as shown in the illustration, connect connector A and lower the green lock to lock it securely.

CAUTION:

Make sure to wear insulating gloves.


NOTICE:

Make sure that the connector is connected securely.




Hide 88711 3.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

a.
I116881N02
1.906,1.979 2.458,2.333 0.552,0.354 18 false iv 0.906,0.094 1.365,0.375 0.458,0.281 18 true i, ii 4.219,0.094 4.771,0.448 0.552,0.354 18 false iii

i.

Remove the vinyl tape from the No. 1 cooler refrigerant discharge hose.


ii.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor with motor assembly.

Compressor Oil:

ND-OIL 11 or equivalent



iii.

Install the O-ring to the No. 1 cooler refrigerant discharge hose.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



iv.

Connect the No. 1 cooler refrigerant discharge hose to the compressor with motor assembly with the bolt.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)



Hide 88704 4.CONNECT SUCTION HOSE SUB-ASSEMBLY

a.
I116882N01
1.906,2 2.458,2.354 0.552,0.354 18 false iii 0.896,0.083 1.448,0.438 0.552,0.354 18 false i 4.229,0.094 4.781,0.448 0.552,0.354 18 false ii

i.

Remove the vinyl tape from the suction hose sub-assembly.


ii.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor with motor assembly.

Compressor Oil:

ND-OIL 11 or equivalent



iii.

Install the O-ring to the suction hose sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



iv.

Connect the suction hose sub-assembly to the compressor with motor assembly with the bolt.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)



Hide 51410 5.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 7.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT