| *1 | ECU INTEGRATION BOX LH | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
1. PRECAUTION
|
|
89221
2.INSTALL MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
|
|
| *1 | Power Distribution Box Assembly | *2 | Main Body ECU (Multiplex Network Body ECU) |
| *a | 20° or more | *b | Housing Sidewall |
| *c | Side A | *d | Center of Rotation (Contacts Surface A) |
|
Push Area |
|
Set |
|
Slide |
|
Install in this Direction |
|
Rotate in this Direction | - | - |
Set the main body ECU (multiplex network body ECU) to the position where the guide of the main body ECU (multiplex network body ECU) contacts the housing sidewall of the power distribution box assembly as shown in the illustration.
Make sure to keep the angle at 20° or more as shown in the illustration.
Slide the main body ECU (multiplex network body ECU) along the housing sidewall as shown in the illustration and engage the guides.
While keeping the main body ECU (multiplex network body ECU) in contact with side A of the power distribution box assembly (axis of rotation), lower it as shown in the illustration.
Do not strike or apply excessive force to the side surface of the main body ECU (multiplex network body ECU).
While pressing the main body ECU (multiplex network body ECU) against side A (center of rotation) of the power distribution box assembly, rotate it until it enters the lock of the power distribution box assembly.
Press the push area until the claw engages to install the main body ECU (multiplex network body ECU).
Make sure to press only the push area.
Confirm the engagement of the main body ECU (multiplex network body ECU) and power distribution box assembly by listening for the click sound of the lock engaging.
If a click sound cannot be heard, visually check the engagement of the lock. The engagement can also be confirmed if the main body ECU (multiplex network body ECU) and power distribution box assembly are flush.
82730G
3.INSTALL POWER DISTRIBUTION BOX ASSEMBLY
4.INSTALL POWER DISTRIBUTION BOX ASSEMBLY WITH MULTIPLEX NETWORK BODY ECU
| *a | Lock Lever | - | - |
Connect the connector.
Connect the 2 connectors and pull down the lock levers to engage the claws and lock the 2 connectors as shown in the illustration.
Engage the claws.
| *a | Nut (A) | *b | Bolt (A) |
Engage the claws.
Install the power distribution box assembly with multiplex network body ECU with the 2 bolts and 2 nuts.
| *A | for HV Model | - | - |
| *a | Lock Lever | - | - |
Connect the each connector.
Connect the 2 connectors and pull down the lock levers to engage the claws and lock the 2 connectors as shown in the illustration.
for HV Model:
1. Connect the 2 connectors and pull down the lock levers to engage the claws and lock the 2 connectors as shown in the illustration.
Engage the clamps.
55405B
5.INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
55550
6.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
55607
7.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
55318F
8.INSTALL NO. 2 INSTRUMENT SIDE PANEL
62312B
9.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Use the same procedure as for the RH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>INSTALLATION
62112
10.INSTALL COWL SIDE TRIM BOARD LH
Use the same procedure as for the RH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
67914B
11.INSTALL FRONT DOOR SCUFF PLATE LH
Use the same procedure as for the RH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
58810J
12.INSTALL CONSOLE BOX ASSEMBLY
55407B
13.INSTALL SWITCH HOLE BASE SUB-ASSEMBLY
55431A
14.INSTALL INSTRUMENT PANEL FINISH PANEL
55432B
15.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL
55475B
16.INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL GARNISH
17.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for M15A-FKS:
Click hereGeneral>MAINTENANCE>M15A-FKS AUXILIARY BATTERY>INSTALLATION
for M15A-FXE:
Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>INSTALLATION
18. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART