| *A | w/ Headup Display | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 7 | INSTRUMENT PANEL CENTER TRAY | 55624A | - | - | - |
| 8 | INSTRUMENT CLUSTER FINISH CENTER PANEL ASSEMBLY | 55420A | - | - | - |
| 9 | RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET | - | - | - | - |
| 10 | INSTRUMENT PANEL CENTER REGISTER ASSEMBLY | 55670A | - | - | - |
| 11 | INSTRUMENT CLUSTER FINISH CENTER PANEL SUB-ASSEMBLY | 55405B | - | - | - |
| 12 | INSTRUMENT CLUSTER FINISH LOWER CENTER PANEL SUB-ASSEMBLY | 55406B | - | - | - |
| 13 | AIR CONDITIONING CONTROL ASSEMBLY | 55900 | - | - | - |
| 14 | COMBINATION METER ASSEMBLY | 83100 | - | - | - |
| 15 | INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY | 55410C | - | - | - |
| *A | for Automatic Air Conditioning System | *B | for Manual Air Conditioning System |
| ● | Non-reusable part | - | - |
| *A | w/ Cover | - | - |
55328
1.INSTALL NO. 1 INSTRUMENT PANEL PIN
89120A
2.INSTALL AUTOMATIC LIGHT CONTROL SENSOR
55950G
3.INSTALL DEFROSTER NOZZLE ASSEMBLY
55302C
4.INSTALL INSTRUMENT PANEL SUB-ASSEMBLY
When installing a new instrument panel sub-assembly:
| *a | Runner Portion | *b | Cut Off |
Using a nipper, cut off both ends of the runner portion.
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the guides to install the instrument panel sub-assembly.
Install the 5 bolts <F>, screw <E> and nut <I>.
Engage the hooks.
Install the 3 clips.
| *a | Airbag Connector | *b | Airbag Bolt |
Install the 2 bolts <G>.
Connect the airbag connector.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Refer to How to Connect or Disconnect Airbag Connector:
Engage the guide and install the ground bracket with the bolt <H>.
Connect the connector.
55313A
5.INSTALL INSTRUMENT MAIN PANEL
55414A
6.INSTALL INSTRUMENT CLUSTER FINISH END PANEL (w/ Headup Display)
55624A
7.INSTALL INSTRUMENT PANEL CENTER TRAY
55420A
8.INSTALL INSTRUMENT CLUSTER FINISH CENTER PANEL ASSEMBLY
86140A
9.INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (w/ Audio)
55670A
10.INSTALL INSTRUMENT PANEL CENTER REGISTER ASSEMBLY
55405B
11.INSTALL INSTRUMENT CLUSTER FINISH CENTER PANEL SUB-ASSEMBLY
55406B
12.INSTALL INSTRUMENT CLUSTER FINISH LOWER CENTER PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)
55900
13.INSTALL AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)
83100
14.INSTALL COMBINATION METER ASSEMBLY
55410C
15.INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
55548A
16.INSTALL INSTRUMENT PANEL HOLE COVER
55480D
17.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
53601
18.CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
86160P
19.INSTALL FRONT NO. 2 SPEAKER ASSEMBLY
62211
20.INSTALL FRONT PILLAR GARNISH RH
Protect the curtain shield airbag assembly:
| *a | Protective Cover | - | - |
|
Adhesive Tape | - | - |
Remove the adhesive tape and protective cover.
Install a new front pillar garnish clips to the front pillar garnish RH.
When installing the front pillar garnish clip, make sure to install it in the correct position and facing in the correct direction.
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the claws to connect the front No.2 speaker assembly.
Engage the guides.
Engage the front pillar garnish clip and clip to install the front pillar garnish LH.
62212
21.INSTALL FRONT PILLAR GARNISH LH
Use the same procedure as for the RH side.
55557A
22.INSTALL GLOVE COMPARTMENT DOOR CHECK CUSHION
55433B
23.INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL
55550
24.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
|
Push |
|
Install in this Direction |
Engage the hinges in the horizontal direction to install the glove compartment door assembly.
Engaging the hinges from the top will deform the hinges.
Be sure to install the glove compartment door assembly horizontally.
While pushing in the sides of the glove compartment door assembly as indicated by the arrows in the illustration, close the door to engage it to the 2 stoppers.
55317E
25.INSTALL NO. 1 INSTRUMENT SIDE PANEL
55318F
26.INSTALL NO. 2 INSTRUMENT SIDE PANEL
62311B
27.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH
62312B
28.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
55607
29.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
55606
30.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
62111C
31.INSTALL COWL SIDE TRIM BOARD RH
62112
32.INSTALL COWL SIDE TRIM BOARD LH
Use the same procedure as for the RH side.
67913B
33.INSTALL FRONT DOOR SCUFF PLATE RH
67914B
34.INSTALL FRONT DOOR SCUFF PLATE LH
Use the same procedure as for the RH side.
84329
35.INSTALL TURN SIGNAL SWITCH
58910C
36.INSTALL REAR CONSOLE BOX ASSEMBLY
37.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for M15A-FKS:
Click hereGeneral>MAINTENANCE>M15A-FKS AUXILIARY BATTERY>INSTALLATION
for M15A-FXE:
Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>INSTALLATION
38. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART