Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING ECU › 2020.08–2021.07
RM3700E _55 Steering _093027 POWER ASSIST SYSTEMS _0438530 POWER STEERING ECU A

POWER ASSIST SYSTEMS  POWER STEERING ECU  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C441748N02
0.823,0.073 6.25,3.719 5.427,3.646 4.667,0.188 5.885,1.813 1.219,1.625 5.281,0.344 5.573,0.344 false 6.25,1.938 6.583,1.938 false 5.188,1.813 5.188,1.99 false 1.479,2.792 1.479,3.052 false 1.49,1.417 1.99,1.417 false 2.198,1.917 2.375,1.917 2.375,1.917 2.51,1.719 false 2.125,2.302 2.125,2.563 false 5.635,0.271 5.792,0.469 0.156,0.198 10 false ● 6.615,1.802 6.896,2.156 0.281,0.354 18 false 1 5.219,1.99 5.5,2.344 0.281,0.354 18 false 2 1.458,3.094 1.74,3.448 0.281,0.354 18 false 3 1.281,1.313 1.563,1.667 0.281,0.354 18 false 4 5.344,0.406 5.656,0.604 0.313,0.198 10 false x2 2.156,0.313 2.469,0.51 0.313,0.198 10 false x3 2.063,1.823 2.219,2.021 0.156,0.198 10 false ● 1.948,2.625 2.563,2.823 0.615,0.198 10 false ● *1 4.729,0.25 5.104,0.49 0.375,0.24 12 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

1 STEERING COLUMN ASSEMBLY - - - -
2 STEERING LOCK ACTUATOR ASSEMBLY 45020B (Click here) - -
3 BRACKET - (Click here) - -
4 POWER STEERING ECU ASSEMBLY 89650 (Click here) - -

*A w/ Entry and Start System - -
*1 CLIP BAND - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the power steering ECU with motor assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Power steering ECU assembly Assist map writing
·

DTCs are stored

·

EPS warning light illuminates

·

Vehicle control history (RoB) are stored


(Click here)
Update ECU security key Vehicle control history (RoB) are stored (Click here)

PROCEDURE

Hide 1.REMOVE STEERING COLUMN ASSEMBLY

Hide 45020B 2.REMOVE STEERING LOCK ACTUATOR ASSEMBLY (w/ Entry and Start System)

Hide 3.REMOVE BRACKET

a.
C441752C01
2.708,0.063 2.99,0.365 0.281,0.302 18 false iii 1.458,0.365 1.667,0.646 0.208,0.281 18 true i 6.417,1.115 6.719,1.427 0.302,0.313 18 false v 6.573,1.469 6.802,1.771 0.229,0.302 18 false iv 2.927,0.448 3.135,0.729 0.208,0.281 18 true ii 1.75,0.813 1.958,1.094 0.208,0.281 18 true iii 2.406,0.885 2.615,1.167 0.208,0.281 18 false iii 2.406,1.458 2.615,1.74 0.208,0.281 18 false iii

i.

Remove the screw.


ii.

Cut the clip band.

NOTICE:

Do not damage the wire harness when cutting the clip band.



iii.

Disconnect the connector and disengage the clamps.


iv.

Using a 5 mm hexagon socket wrench, remove the bolt.


v.

Disengage the guide to remove the bracket.



Hide 89650 4.REMOVE POWER STEERING ECU ASSEMBLY

Z101186

NOTICE:
·

Do not drop the power steering ECU assembly, strike it with tools or subject it to impacts.

·

If the power steering ECU assembly is subjected to an impact, replace it with a new one.

·

Do not pull the wire harness of the power steering column assembly.

·

Do not allow any moisture to come into contact with the power steering ECU assembly.

·

Do not loosen any bolts not mentioned in the procedure.

·

Do not allow any foreign matter to contaminate the power steering ECU assembly.




a.
C441749N01
2.615,0.188 2.896,0.542 0.281,0.354 18 false i

i.

Using a 4 mm hexagon socket wrench, remove the 3 bolts and power steering ECU assembly.