Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY › 2020.08–2021.07
RM3700E _55 Steering _093030 STEERING COLUMN _0438540 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (REASSEMBLY)
C441789N02
5.292,0.51 5.531,0.51 false 4.208,0.823 4.208,1.167 false 3.656,1.802 3.656,2.063 false 1.823,1.5 1.823,1.844 false 2.99,1.24 2.99,1.583 false 5.604,0.385 5.885,0.74 0.281,0.354 18 false 4 3.583,2.104 3.865,2.458 0.281,0.354 18 false 3 4.25,1.208 4.531,1.563 0.281,0.354 18 false 2 1.76,1.875 2.042,2.229 0.281,0.354 18 false 1 0.073,0.063 0.448,0.302 0.375,0.24 12 false *A 2.927,1.604 3.24,1.802 0.313,0.198 10 false *1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 IGNITION OR STARTER SWITCH ASSEMBLY 84450 - - -
2 IGNITION SWITCH LOCK CYLINDER ASSEMBLY - (Click here) - -
3 UN-LOCK WARNING SWITCH ASSEMBLY 84052 - - -
4 TRANSPONDER KEY COIL 89782 - - -

*A w/o Entry and Start System - -
*1 UPPER STEERING COLUMN BRACKET ASSEMBLY - -

C441790N02
3.615,0.083 6.979,2.344 3.365,2.26 5.469,0.156 6.771,1.771 1.302,1.615 3.948,0.177 5.083,1.802 1.135,1.625 0.677,0.25 1.646,0.417 0.969,0.167 0.313,3.073 1.104,3.24 0.792,0.167 5.177,2.344 5.177,0.083 false 4.49,1.802 4.49,1.969 false 6.125,1.771 6.125,2.021 false 1.854,2.865 1.854,3.146 false 1.427,1.313 1.896,1.313 false 4.271,0.375 4.49,0.375 false 5.76,0.354 5.979,0.354 false 1.646,0.333 1.979,0.333 false 1.104,3.156 1.271,3.156 1.271,3.156 1.354,2.74 false 2.188,1.917 2.344,1.917 2.344,1.917 2.49,1.719 false 2.208,2.281 2.208,2.531 false 5.198,2.875 5.531,2.875 false 3.667,0.125 4.042,0.365 0.375,0.24 12 false *A 5.229,0.125 5.604,0.365 0.375,0.24 12 false *B 4.448,1.99 4.729,2.344 0.281,0.354 18 false 7 6.063,2.042 6.344,2.396 0.281,0.354 18 false 8 1.813,3.156 2.094,3.51 0.281,0.354 18 false 6 1.25,1.188 1.531,1.542 0.281,0.354 18 false 5 2.125,0.302 2.438,0.5 0.313,0.198 10 false x3 4.615,0.354 4.927,0.552 0.313,0.198 10 false x2 6.094,0.354 6.406,0.552 0.313,0.198 10 false x2 4.115,0.292 4.271,0.49 0.156,0.198 10 false ● 5.583,0.26 5.74,0.458 0.156,0.198 10 false ● 0.719,0.25 3.167,0.406 2.448,0.156 8 false 6.5 (66, 58 in.*lbf) 0.354,3.083 2.073,3.24 1.719,0.156 8 false 16.5 (168, 12) 2.052,1.833 2.208,2.031 0.156,0.198 10 false ● 2.083,2.583 2.438,2.844 0.354,0.26 10 false ● *2 5.583,2.792 5.865,3.052 0.281,0.26 10 false *1

Procedure Part Name Code
Z101186

Z101188

Z101187

5 POWER STEERING ECU ASSEMBLY 89650 (Click here) - -
6 BRACKET - (Click here) - -
7 STEERING LOCK ACTUATOR ASSEMBLY 45020B (Click here) - -
8 UPPER STEERING COLUMN BRACKET WITH SWITCH ASSEMBLY 45020B - - -

*A w/ Entry and Start System *B w/o Entry and Start System
*1 ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY *2 CLIP BAND
V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part
V100135

Grease - -

CAUTION / NOTICE / HINT

NOTICE:
·

Do not drop the power steering ECU with motor assembly, strike it with tools or subject it to impacts.

·

If the power steering ECU with motor assembly is subjected to an impact, replace it with a new one.

·

Do not pull the wire harness.

·

Do not allow any moisture to come into contact with the power steering ECU with motor assembly.

·

Do not loosen any bolts not mentioned in the procedure.

·

Do not allow any foreign matter to contaminate the power steering ECU with motor assembly.



PROCEDURE

Hide 84450 1.INSTALL IGNITION OR STARTER SWITCH ASSEMBLY (w/o Entry and Start System)

Hide 2.INSTALL IGNITION SWITCH LOCK CYLINDER ASSEMBLY (w/o Entry and Start System)

a.
C441791C01
2.021,0.292 2.302,0.646 0.281,0.354 18 false i 2.979,2.438 3.531,2.792 0.552,0.354 18 false ii
V113147

Install in this direction - -


i.

Turn the ignition switch to ACC.


ii.

Install the ignition switch lock cylinder assembly to the upper steering column bracket assembly as shown in the illustration.



Hide 84052 3.INSTALL UN-LOCK WARNING SWITCH ASSEMBLY (w/o Entry and Start System)

Hide 89782 4.INSTALL TRANSPONDER KEY COIL (w/o Entry and Start System)

Hide 89650 5.INSTALL POWER STEERING ECU ASSEMBLY

Hide 45020B 7.INSTALL STEERING LOCK ACTUATOR ASSEMBLY (w/ Entry and Start System)

Z101186

HINT:

When replacing the steering lock actuator assembly, refer to Service Bulletin.



a.
C441768C01
1.135,0.865 1.604,0.979 true 2.406,1.115 2.917,1.115 true 2.427,1.406 2.688,1.406 2.688,1.406 2.688,1.125 false 2.427,1.24 2.677,1.24 true 0.792,0.125 1.073,0.479 0.281,0.354 18 false i 4.24,0.104 4.802,0.49 0.563,0.385 18 false ii, iii 0.948,0.76 1.26,0.958 0.313,0.198 10 false *a 2.969,1.031 3.281,1.229 0.313,0.198 10 false *b
*a Cloth *b Wooden Block


i.

Secure the steering column assembly in a vise between aluminum plates, cloths and wooden blocks.

NOTICE:
·

Do not overtighten the vise, as the steering column assembly may become deformed.

·

Support the steering column assembly with wooden blocks or similar items to ensure that it does not fall.




ii.

Temporarily install the steering lock actuator assembly and upper steering column clamp with 2 new steering lock set bolts.


iii.

Tighten the 2 steering lock set bolts until the bolt head breaks off.



Hide 45020B 8.INSTALL UPPER STEERING COLUMN BRACKET WITH SWITCH ASSEMBLY (w/o Entry and Start System)

a.

Use the same procedure for the steering lock actuator assembly.