| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | POWER STEERING ECU ASSEMBLY | 89650 | ( )
|
- | - |
| 2 | BRACKET | - | ( )
|
- | - |
| 3 | STEERING LOCK ACTUATOR ASSEMBLY | 45020 | ( )
|
- | - |
| *A | w/ Entry and Start System | - | - |
| *1 | CLIP BAND | *2 | ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
Grease | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 19 | TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY | - | ( )
|
- | - |
| 20 | UPPER STEERING COLUMN COVER | 45286B | - | - | - |
| 21 | LOWER STEERING COLUMN COVER | 45287 | - | - | - |
After performing the update ECU security key procedure, make sure to perform the initialization procedure for when the cable has been disconnected and reconnected to the negative (-) auxiliary battery terminal.
89650
1.INSTALL POWER STEERING ECU ASSEMBLY
|
|
| *1 | O-ring | - | - |
| *a | Cloth | *b | Wooden Block |
Install the O-ring to the power steering ECU assembly.
Apply grease the power steering ECU assembly.
Apply the grease supplied with the power steering ECU assembly.
Using a 4 mm hexagon socket wrench, temporarily install the power steering ECU assembly to the electric power steering column sub-assembly with the 3 bolts.
When temporarily installing the 3 bolts to the power steering ECU assembly, do not tighten them all the way down.
Using a 10 mm hexagon socket wrench, install the steering wheel assembly set bolt to the steering main shaft.
Do not apply excessive torque to the steering wheel assembly set bolt by using a tool such as an impact wrench.
The steering wheel assembly set bolt is used for turning the steering main shaft during inspection of the steering main shaft rotating torque.
Remove the steering wheel assembly set bolt after performing this inspection.
Secure the steering column assembly in a vise using aluminum plates, cloths and wooden blocks.
Do not overtighten the vise, as the steering column assembly may become deformed.
Secure the power steering ECU assembly so that it is upright.
Support the steering column assembly with wooden blocks or similar items to ensure that it does not fall.
Rotate the steering main shaft 180 degrees counterclockwise and then 180 degrees clockwise at a speed of 60 rpm, and repeat 2 to 3 times to center the axis of the power steering ECU assembly. [*1]
Using a 4 mm hexagon socket wrench, tighten the 3 bolts. [*2]
Using a torque wrench, measure the turning torque of the steering main shaft.
0.9 to 3.0 N*m (10 to 30 kgf*cm, 8 to 26 in.*lbf)
Ensure that there is no abnormal resistance during rotation.
If the turning torque is not as specified, loosen the 2 bolts and repeat steps [*1] and [*2] to recenter the axis of the power steering ECU assembly.
Remove the steering wheel assembly set bolt.
2.INSTALL BRACKET
Engage the guide to install the bracket.
Using a 5 mm hexagon socket wrench, install the bolt.
Install the screw.
Connect the connector and engage the clamps.
Using a new clip band to bundle the 2 wire harness together and connect them to the bracket.
4. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
45259A
8.INSTALL COLUMN HOLE COVER SILENCER SHEET
87211
9.INSTALL NO. 1 AIR DUCT
84340
10.INSTALL STOP LIGHT SWITCH ASSEMBLY
55480D
11.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
53601
12.CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
55317E
13.INSTALL NO. 1 INSTRUMENT SIDE PANEL
62311B
14.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
55606
15.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
62111C
16.INSTALL COWL SIDE TRIM BOARD RH
67913B
17.INSTALL FRONT DOOR SCUFF PLATE RH
58810J
18.INSTALL FRONT CONSOLE BOX SUB-ASSEMBLY
45286B
20.INSTALL UPPER STEERING COLUMN COVER
45287
21.INSTALL LOWER STEERING COLUMN COVER
25.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for M15A-FKS:
Click hereGeneral>MAINTENANCE>M15A-FKS AUXILIARY BATTERY>INSTALLATION
for M15A-FXE:
Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>INSTALLATION
26. UPDATE ECU SECURITY KEY
45130
27.INSPECT HORN BUTTON ASSEMBLY
Make sure that the horn sounds.
If the horn does not sound, inspect the horn system.
Click hereVehicle Exterior>HORN>HORN SYSTEM>PROBLEM SYMPTOMS TABLE
28. PERFORM DIAGNOSTIC SYSTEM CHECK
29. PERFORM POWER STEERING ECU INITIAL SETTING
31. PERFORM CALIBRATION
32. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
33.ADJUST STEERING CENTER