Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › ULTRASONIC SENSOR (for Rear) › 2020.08–2021.07
RM3700E _56 Audio / Visual / Telematics _093031 PARK ASSIST / MONITORING _0438555 ULTRASONIC SENSOR(for Rear) A

PARK ASSIST / MONITORING  ULTRASONIC SENSOR(for Rear)  REMOVAL  


CAUTION / NOTICE / HINT

CONPONENTS (REMOVAL)
E449720N01
0.708,3.208 1.042,3.208 false 1.688,2.052 2,2.052 false 1.76,1.01 2.094,1.01 false 0.365,2.74 0.698,2.74 false 1.281,1.542 1.615,1.542 false 2.615,0.521 2.865,0.521 false 1.448,3.667 1.802,3.667 false 5.417,4.927 5.417,5.26 false 3.333,1.896 3.583,1.896 false 3.625,0.99 3.625,1.24 false 4.438,1.479 4.438,1.729 false 5.365,5.292 5.646,5.583 0.281,0.292 18 false 1 1.656,1.396 1.938,1.75 0.281,0.354 18 false 4 1.594,0.844 1.875,1.198 0.281,0.354 18 false 4 3.573,1.26 3.854,1.615 0.281,0.354 18 false 3 0.531,3.073 0.813,3.427 0.281,0.354 18 false 3 1.271,3.5 1.552,3.854 0.281,0.354 18 false 5 4.615,1.771 4.896,2.125 0.281,0.354 18 false 5 1.5,1.906 1.781,2.26 0.281,0.354 18 false 6 3.146,1.76 3.427,2.115 0.281,0.354 18 false 6 3.01,1.813 3.292,2.167 0.281,0.354 10 false ● 1.156,3.552 1.354,3.865 0.198,0.313 10 false ● 1.365,1.948 1.646,2.302 0.281,0.354 10 false ● 4.479,1.813 4.76,2.167 0.281,0.354 10 false ● 2.427,0.333 2.708,0.688 0.281,0.354 18 false 2 0.76,2.552 1.042,2.906 0.281,0.354 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR BUMPER ASSEMBLY - - - -
2 ULTRASONIC SENSOR CLIP 89348D - - -
3 REAR CORNER ULTRASONIC SENSOR 89342 - - -
4 REAR CENTER ULTRASONIC SENSOR 89342A - - -
5 REAR CORNER ULTRASONIC SENSOR RETAINER 89348R (Click here) - -
6 REAR CENTER ULTRASONIC SENSOR RETAINER 89348S (Click here) - -

● Non-reusable part - -

E463470N05
1.521,1.958 1.979,1.958 false 1.302,1.833 1.583,2.188 0.281,0.354 18 false 7

Procedure Part Name Code
Z101186

Z101188

Z101187

7 ULTRASONIC SENSOR CUSHION SET - (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during ultrasonic sensor removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link
Ultrasonic sensor (Including removal and installation)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

TOYOTA parking assist-sensor system

·

Parking support brake system


(Click here)

PROCEDURE

Hide 1.REMOVE REAR BUMPER ASSEMBLY

Hide 89348D 2.REMOVE ULTRASONIC SENSOR CLIP

a.
E449662


b.

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


Hide 89342 3.REMOVE REAR CORNER ULTRASONIC SENSOR

a.
E449664


b.

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


Hide 89342A 4.REMOVE REAR CENTER ULTRASONIC SENSOR

a.
E449663


b.

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


Hide 89348R 5.REMOVE REAR CORNER ULTRASONIC SENSOR RETAINER

Z101186

NOTICE:
·

Perform this procedure only when replacement of the rear corner ultrasonic sensor retainer is necessary.

·

When removing the rear corner ultrasonic sensor retainer, if the double-sided tape is difficult to remove, heat the rear bumper assembly and rear corner ultrasonic sensor retainer using a heat light.




a.
E449656C02
0.396,0.073 0.625,0.375 0.229,0.302 18 false i 3.688,0.052 3.99,0.344 0.302,0.292 18 false ii
V100145

Heated Area - -


i.

Heat the rear bumper assembly and rear corner ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.

Heating Temperature:
Item Temperature
Rear Bumper Assembly 40 to 60°C (104 to 140°F)
Rear Corner Ultrasonic Sensor Retainer


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear bumper assembly and rear corner ultrasonic sensor retainer excessively.



ii.

Remove the rear corner ultrasonic sensor retainer.



b.

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


Hide 89348S 6.REMOVE REAR CENTER ULTRASONIC SENSOR RETAINER

Z101186

NOTICE:
·

Perform this procedure only when replacement of the rear center ultrasonic sensor retainer is necessary.

·

When removing the rear center ultrasonic sensor retainer, if the double-sided tape is difficult to remove, heat the rear bumper assembly and rear center ultrasonic sensor retainer using a heat light.




a.
E449656C02
0.396,0.073 0.625,0.375 0.229,0.302 18 false i 3.688,0.052 3.99,0.344 0.302,0.292 18 false ii
V100145

Heated Area - -


i.

Heat the rear bumper assembly and rear center ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.

Heating Temperature:
Item Temperature
Rear Bumper Assembly 40 to 60°C (104 to 140°F)
Rear Center Ultrasonic Sensor Retainer


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear bumper assembly and rear center ultrasonic sensor retainer excessively.



ii.

Remove the rear center ultrasonic sensor retainer.



b.

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


Hide 7.REMOVE ULTRASONIC SENSOR CUSHION SET

Z101186

NOTICE:

Perform this procedure only when replacement of the ultrasonic sensor cushion set is necessary.



a.
E463471