Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2020.08–2021.07
RM3700E _58 Vehicle Interior _093087 METER / GAUGE / DISPLAY _0438738 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B150819  Turn Signal/Hazard Flasher Circuit Current Above Threshold  


DESCRIPTION

This DTC is stored when the combination meter assembly detects a short in a turn signal light circuit.

HINT:

If there is a short in a turn signal light circuit, all of the turn signal lights in that circuit will not blink.


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B150819 Turn Signal/Hazard Flasher Circuit Current Above Threshold Diagnosis Condition:

Auxiliary battery voltage is 10 V or more


Malfunction Status:

Short in turn signal light circuit


·

for Front Turn Signal Light:

-

Front turn signal light socket*1

-

Front turn signal light bulb*1

-

Daytime running light assembly LH*2

-

Daytime running light assembly RH*2


·

for Side turn signal light:

-

Side turn signal light assembly LH

-

Side turn signal light assembly RH

-

Outer rear view mirror assembly LH

-

Outer rear view mirror assembly LH


·

for Rear Turn Signal Light:

-

Rear turn signal light socket*3

-

Rear turn signal light bulb*3

-

Rear combination light assembly LH*4

-

Rear combination light assembly RH*4

-

Rear light assembly LH*4

-

Rear light assembly RH*4


·

Wire harness or connector

·

Combination meter assembly


Combination Meter A

*1: for Halogen Headlight

*2: for LED Headlight

*3: for Rear Turn Signal Light Bulb Type

*4: for Rear Turn Signal Light LED Type


WIRING DIAGRAM

E450264E03
0.167,0.167 1.458,0.594 1.292,0.427 12 false for LH Side: 1.104,1.667 3.354,2 2.25,0.333 10 false Front Turn Signal Light Socket 0.458,2.104 0.917,2.302 0.458,0.198 10 false B14 0.417,3.75 0.875,3.948 0.458,0.198 10 false B12 0.417,3.927 3.146,4.292 2.729,0.365 10 false Daytime Running Light Assembly LH*2 0.458,2.292 2.969,2.667 2.51,0.375 10 false Daytime Running Light Assembly LH*1 0.333,6.083 2.75,6.417 2.417,0.333 10 false Outer Rear View Mirror Assembly LH 0.51,5.635 2.823,5.969 2.313,0.333 10 false Side Turn Signal Light Assembly LH 0.167,6.75 2.188,7.083 2.021,0.333 10 false *1: for Halogen Headlight 0.167,7.083 2.188,7.417 2.021,0.333 10 false *2: for LED Headlight 0.167,7.417 2.188,7.75 2.021,0.333 10 false *3: w/o Mirror Heater 2.333,7.083 6.146,7.458 3.813,0.375 10 false *4: w/o Panoramic View Monitor System with Mirror Heater 5.073,6.25 5.385,6.448 0.313,0.198 10 false H7 5.063,6.417 6.979,6.854 1.917,0.438 10 false Combination Meter Assembly 5.938,3.281 6.844,3.677 0.906,0.396 10 false FLASHER IC 3.938,1 4.25,1.198 0.313,0.198 10 false *1 3.938,2.844 4.25,3.042 0.313,0.198 10 false *2 3.302,5.021 3.615,5.219 0.313,0.198 10 false *4 2.906,5.021 3.219,5.219 0.313,0.198 10 false *5 2.906,5.604 3.219,5.802 0.313,0.198 10 false *5 3.719,5.021 4.031,5.219 0.313,0.198 10 false *3 3.719,5.604 4.031,5.802 0.313,0.198 10 false *3 3.323,5.604 3.635,5.802 0.313,0.198 10 false *4 5.042,1 5.354,1.198 0.313,0.198 10 false LL 4.833,1 4.99,1.198 0.156,0.198 10 false 1 2.917,1 3.073,1.198 0.156,0.198 10 false B 2.917,2.844 3.073,3.042 0.156,0.198 10 false B 2.625,4.698 2.781,4.896 0.156,0.198 10 false B 2.625,5.271 2.781,5.469 0.156,0.198 10 false - 2.917,3.146 3.073,3.344 0.156,0.198 10 false E 2.917,1.292 3.073,1.49 0.156,0.198 10 false E 3.115,1 3.271,1.198 0.156,0.198 10 false 1 3.115,1.302 3.271,1.5 0.156,0.198 10 false 2 3.115,2.844 3.271,3.042 0.156,0.198 10 false 3 3.115,3.146 3.271,3.344 0.156,0.198 10 false 1 3.677,4.802 4.135,5 0.458,0.198 10 false L10 3.677,5.385 4.135,5.583 0.458,0.198 10 false L10 3.271,4.802 3.729,5 0.458,0.198 10 false L12 3.271,5.396 3.729,5.594 0.458,0.198 10 false L12 2.917,5.396 3.375,5.594 0.458,0.198 10 false L8 2.917,4.813 3.375,5.01 0.458,0.198 10 false L8 3.74,4.615 3.896,4.813 0.156,0.198 10 false 5 3.313,4.615 3.625,4.813 0.313,0.198 10 false 10 2.906,4.615 3.219,4.813 0.313,0.198 10 false 16 2.885,5.198 3.198,5.396 0.313,0.198 10 false 15 3.313,5.198 3.625,5.396 0.313,0.198 10 false 11 3.75,5.198 3.906,5.396 0.156,0.198 10 false 4 2.333,7.417 6.146,7.792 3.813,0.375 10 false *5: w/ Panoramic View Monitor System with Mirror Heater

E450265E07
0.177,0.167 1.479,0.625 1.302,0.458 12 false for LH Side: 1.281,1.917 3.719,2.25 2.438,0.333 10 false Rear Turn Signal Light Socket 5.052,1.25 5.667,1.448 0.615,0.198 10 false TRNL 5.938,1.688 6.844,2.052 0.906,0.365 10 false FLASHER IC 5.99,3.792 6.604,4.135 0.615,0.344 10 false TURN L 4.823,1.25 4.979,1.448 0.156,0.198 10 false 5 0.583,2.51 3.229,2.917 2.646,0.406 10 false Rear Combination Light Assembly LH*1 0.583,2.333 1.198,2.531 0.615,0.198 10 false O101 3.052,1.25 3.208,1.448 0.156,0.198 10 false B 3.063,1.552 3.219,1.75 0.156,0.198 10 false E 3.292,1.25 3.448,1.448 0.156,0.198 10 false 1 3.292,1.552 3.448,1.75 0.156,0.198 10 false 2 3.281,3.427 3.438,3.625 0.156,0.198 10 false 2 0.813,3.427 0.969,3.625 0.156,0.198 10 false 1 0.885,4.458 3.552,4.875 2.667,0.417 10 false Rear Combination Light Assembly LH*2 0.885,4.281 1.5,4.479 0.615,0.198 10 false O107 1.292,6.427 3.771,6.792 2.479,0.365 10 false Rear Light Assembly LH*2 1.292,6.24 1.75,6.438 0.458,0.198 10 false Y12 3.063,3.542 3.219,3.74 0.156,0.198 10 false B 1.021,3.542 1.177,3.74 0.156,0.198 10 false E 1.031,5.927 1.188,6.125 0.156,0.198 10 false E 2.885,5.906 3.344,6.104 0.458,0.198 10 false TRN 1.01,5.49 1.625,5.688 0.615,0.198 10 false TRN4 1.01,3.948 1.625,4.146 0.615,0.198 10 false TRN4 0.802,3.844 0.958,4.042 0.156,0.198 10 false 4 0.802,5.375 0.958,5.573 0.156,0.198 10 false 1 0.802,5.792 0.958,5.99 0.156,0.198 10 false 2 3.271,5.792 3.427,5.99 0.156,0.198 10 false 4 4.031,1.25 4.344,1.448 0.313,0.198 10 false *1 4.458,1.75 4.771,1.948 0.313,0.198 10 false *2 5.073,6.417 5.385,6.615 0.313,0.198 10 false H7 5.063,6.583 6.917,7 1.854,0.417 10 false Combination Meter Assembly 0.167,7.083 3.667,7.417 3.5,0.333 10 false *1: for Rear Turn Signal Light Bulb Type 0.167,7.417 3.5,7.75 3.333,0.333 10 false *2: for Rear Turn Signal Light LED Type

E450264E04
0.167,0.167 1.521,0.542 1.354,0.375 12 false for RH Side: 1.125,1.667 3.375,2 2.25,0.333 10 false Front Turn Signal Light Socket 0.583,2.104 1.042,2.302 0.458,0.198 10 false B15 0.583,3.75 1.042,3.948 0.458,0.198 10 false B13 0.583,3.927 3.25,4.302 2.667,0.375 10 false Daytime Running Light Assembly RH*2 0.583,2.292 3.219,2.646 2.635,0.354 10 false Daytime Running Light Assembly RH*1 0.333,6.083 2.771,6.438 2.438,0.354 10 false Outer Rear View Mirror Assembly RH 0.479,5.646 2.792,5.979 2.313,0.333 10 false Side Turn Signal Light Assembly RH 0.167,6.75 2.188,7.083 2.021,0.333 10 false *1: for Halogen Headlight 0.167,7.083 2.188,7.417 2.021,0.333 10 false *2: for LED Headlight 0.167,7.417 2.188,7.75 2.021,0.333 10 false *3: w/o Mirror Heater 2.333,7.083 6.177,7.417 3.844,0.333 10 false *4: w/o Panoramic View Monitor System with Mirror Heater 5.094,6.25 5.406,6.448 0.313,0.198 10 false H7 5.073,6.417 6.979,6.844 1.906,0.427 10 false Combination Meter Assembly 5.948,3.281 6.854,3.677 0.906,0.396 10 false FLASHER IC 3.938,1 4.25,1.198 0.313,0.198 10 false *1 3.938,2.844 4.25,3.042 0.313,0.198 10 false *2 3.302,5.021 3.615,5.219 0.313,0.198 10 false *4 2.906,5.021 3.219,5.219 0.313,0.198 10 false *5 2.906,5.604 3.219,5.802 0.313,0.198 10 false *5 3.719,5.021 4.031,5.219 0.313,0.198 10 false *3 3.719,5.604 4.031,5.802 0.313,0.198 10 false *3 3.323,5.604 3.635,5.802 0.313,0.198 10 false *4 5.042,1 5.354,1.198 0.313,0.198 10 false LR 4.833,1 4.99,1.198 0.156,0.198 10 false 2 2.917,1 3.073,1.198 0.156,0.198 10 false B 2.917,2.844 3.073,3.042 0.156,0.198 10 false B 2.625,4.698 2.781,4.896 0.156,0.198 10 false B 2.625,5.271 2.781,5.469 0.156,0.198 10 false - 2.917,3.146 3.073,3.344 0.156,0.198 10 false E 2.917,1.292 3.073,1.49 0.156,0.198 10 false E 3.115,1 3.271,1.198 0.156,0.198 10 false 1 3.115,1.302 3.271,1.5 0.156,0.198 10 false 2 3.115,2.844 3.271,3.042 0.156,0.198 10 false 3 3.115,3.146 3.271,3.344 0.156,0.198 10 false 1 3.677,4.802 4.135,5 0.458,0.198 10 false K10 3.677,5.385 4.135,5.583 0.458,0.198 10 false K10 3.271,4.802 3.729,5 0.458,0.198 10 false K13 3.271,5.396 3.729,5.594 0.458,0.198 10 false K13 2.917,5.396 3.375,5.594 0.458,0.198 10 false K8 2.917,4.813 3.375,5.01 0.458,0.198 10 false K8 3.74,4.615 3.896,4.813 0.156,0.198 10 false 5 3.313,4.615 3.625,4.813 0.313,0.198 10 false 10 2.906,4.615 3.219,4.813 0.313,0.198 10 false 16 2.885,5.198 3.198,5.396 0.313,0.198 10 false 15 3.313,5.198 3.625,5.396 0.313,0.198 10 false 11 3.75,5.198 3.906,5.396 0.156,0.198 10 false 4 2.333,7.417 6.177,7.75 3.844,0.333 10 false *5: w/ Panoramic View Monitor System with Mirror Heater

E450265E08
0.177,0.167 1.219,0.5 1.042,0.333 12 false for RH Side: 1.281,1.917 3.719,2.25 2.438,0.333 10 false Rear Turn Signal Light Socket 5.052,1.25 5.667,1.448 0.615,0.198 10 false TRNR 5.938,1.688 6.844,2.052 0.906,0.365 10 false FLASHER IC 5.99,3.792 6.604,4.135 0.615,0.344 10 false TURN R 4.823,1.25 4.979,1.448 0.156,0.198 10 false 6 0.75,2.51 3.417,2.906 2.667,0.396 10 false Rear Combination Light Assembly RH*1 0.75,2.333 1.365,2.531 0.615,0.198 10 false O103 3.052,1.25 3.208,1.448 0.156,0.198 10 false B 3.063,1.552 3.219,1.75 0.156,0.198 10 false E 3.292,1.25 3.448,1.448 0.156,0.198 10 false 1 3.292,1.552 3.448,1.75 0.156,0.198 10 false 2 3.281,3.427 3.438,3.625 0.156,0.198 10 false 2 0.813,3.427 0.969,3.625 0.156,0.198 10 false 1 1.031,4.458 3.594,4.844 2.563,0.385 10 false Rear Combination Light Assembly RH*2 1.031,4.281 1.646,4.479 0.615,0.198 10 false O110 1.25,6.427 3.729,6.792 2.479,0.365 10 false Rear Light Assembly RH*2 1.25,6.24 1.708,6.438 0.458,0.198 10 false Y14 3.063,3.542 3.219,3.74 0.156,0.198 10 false B 1.021,3.542 1.177,3.74 0.156,0.198 10 false E 1.031,5.927 1.188,6.125 0.156,0.198 10 false E 2.885,5.906 3.344,6.104 0.458,0.198 10 false TRN 1.01,5.49 1.625,5.688 0.615,0.198 10 false TRN4 1.01,3.948 1.625,4.146 0.615,0.198 10 false TRN4 0.802,3.844 0.958,4.042 0.156,0.198 10 false 4 0.802,5.375 0.958,5.573 0.156,0.198 10 false 1 0.802,5.792 0.958,5.99 0.156,0.198 10 false 2 3.271,5.792 3.427,5.99 0.156,0.198 10 false 4 4.031,1.25 4.344,1.448 0.313,0.198 10 false *1 4.458,1.75 4.771,1.948 0.313,0.198 10 false *2 5.094,6.417 5.406,6.615 0.313,0.198 10 false H7 5.073,6.583 6.958,7.063 1.885,0.479 10 false Combination Meter Assembly 0.167,7.083 3.667,7.417 3.5,0.333 10 false *1: for Rear Turn Signal Light Bulb Type 0.167,7.417 3.5,7.75 3.333,0.333 10 false *2: for Rear Turn Signal Light LED Type

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

Inspect the turn signal light bulbs before performing the following procedure.



PROCEDURE

1.CHECK SYMPTOMS
a.

Check the problem symptoms.


Result:
Result Proceed to
All LH side turn signal lights do not blink A
All RH side turn signal lights do not blink B



A

2.CHECK VEHICLE TYPE

B

21.CHECK VEHICLE TYPE
2.CHECK VEHICLE TYPE
a.

Check vehicle condition.

Result:
Result Proceed to
for Halogen Headlight and Rear Turn Signal Light Bulb Type A
for LED Headlight and Rear Turn Signal Light LED Type B




A

3.CHECK LH SIDE TURN SIGNAL LIGHTS (FRONT TURN SIGNAL LIGHT CIRCUIT)

B

11.CHECK LH SIDE TURN SIGNAL LIGHTS (FRONT TURN SIGNAL LIGHT CIRCUIT)
3.CHECK LH SIDE TURN SIGNAL LIGHTS (FRONT TURN SIGNAL LIGHT CIRCUIT)

Pre-procedure1

a.

Disconnect the B14 daytime running light assembly LH connector.


Procedure1

a.

Operate the turn signal switch and check that the LH side turn signal lights other than the front turn signal light blink.

HINT:

If the LH side turn signal lights other than the front turn signal light blink, the daytime running light assembly LH is malfunctioning.


Result:
Result Proceed to
LH side turn signal lights other than the front turn signal light blink A
All LH side turn signal lights do not blink B



Post-procedure1

a.

None



A

REPLACE FRONT TURN SIGNAL LIGHT SOCKET

B

4.CHECK LH SIDE TURN SIGNAL LIGHTS (SIDE TURN SIGNAL LIGHT CIRCUIT)
4.CHECK LH SIDE TURN SIGNAL LIGHTS (SIDE TURN SIGNAL LIGHT CIRCUIT)

Pre-procedure1

a.

Connect the daytime running light assembly LH connector.


b.

Disconnect the L10*1, L12*2 or L8*3 outer rear view mirror assembly LH connector.

*1: w/o Mirror Heater

*2: w/o Panoramic View Monitor System with Mirror Heater

*3: w/ Panoramic View Monitor System with Mirror Heater



Procedure1

a.

Operate the turn signal switch and check that the LH side turn signal lights other than the side turn signal light blink.

HINT:

If the LH side turn signal lights other than the side turn signal light blink, a component of the outer rear view mirror assembly LH is malfunctioning.


Result:
Result Proceed to
LH side turn signal lights other than the side turn signal light blink A
All LH side turn signal lights do not blink B



Post-procedure1

a.

None



A

5.CHECK LH SIDE TURN SIGNAL LIGHTS (OUTER REAR VIEW MIRROR ASSEMBLY LH)

B

6.CHECK LH SIDE TURN SIGNAL LIGHTS (REAR TURN SIGNAL LIGHT CIRCUIT)
5.CHECK LH SIDE TURN SIGNAL LIGHTS (OUTER REAR VIEW MIRROR ASSEMBLY LH)

Pre-procedure1

a.

Remove the side turn signal light assembly LH from outer rear view mirror assembly LH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL



b.

Connect the outer rear view mirror assembly LH connector.


Procedure1

a.

Operate the turn signal switch and check that the LH side turn signal lights other than the side turn signal light blink.

HINT:

If all LH side turn signal lights do not blink, the outer rear view mirror assembly LH is malfunctioning.


Result:
Result Proceed to
LH side turn signal lights other than the side turn signal light blink A
All LH side turn signal lights do not blink B



Post-procedure1

a.

None



A

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY LH

B

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

6.CHECK LH SIDE TURN SIGNAL LIGHTS (REAR TURN SIGNAL LIGHT CIRCUIT)

Pre-procedure1

a.

Connect the outer rear view mirror assembly LH connector.


b.

Disconnect the O101 rear combination light assembly LH connector.


Procedure1

a.

Operate the turn signal switch and check that the LH side turn signal lights other than the rear turn signal light blink.

HINT:

If the LH side turn signal lights other than the rear turn signal light blink, the rear combination light assembly LH is malfunctioning.


Result:
Result Proceed to
LH side turn signal lights other than the rear turn signal light blink A
All LH side turn signal lights do not blink B



Post-procedure1

a.

None



A

REPLACE REAR TURN SIGNAL LIGHT SOCKET

B

7.CHECK VEHICLE TYPE
7.CHECK VEHICLE TYPE
a.

Check vehicle condition.

Result:
Result Proceed to
w/o Mirror Heater A
w/o Panoramic View Monitor System with Mirror Heater B
w/ Panoramic View Monitor System with Mirror Heater C




A

8.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

B

9.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

C

10.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)
8.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the B14 daytime running light assembly LH connector.


b.

Disconnect the L10 outer rear view mirror assembly LH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B14,L10,O101,H7)Location & Routing

Click Connector(B14)Engine Compartment>No. 3 Engine Room Wire>Daytime Running Light Assembly LH

Click Connector(L10)Body>Front Door Wire LH / Television Camera Wire>Outer Rear View Mirror Assembly LH

Click Connector(O101)Body>Floor Wire>Rear Combination Light Assembly LH

Click Connector(H7)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

B14-1 (B) - Body ground Always 10 kΩ or higher
L10-4 (B) - Body ground Always 10 kΩ or higher
O101-1 (B) - Body ground Always 10 kΩ or higher
H7-1 (LL) - Body ground Always 10 kΩ or higher
H7-5 (TRNL) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the B14 daytime running light assembly LH connector.


b.

Disconnect the L12 outer rear view mirror assembly LH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B14,L12,O101,H7)Location & Routing

Click Connector(B14)Engine Compartment>No. 3 Engine Room Wire>Daytime Running Light Assembly LH

Click Connector(L12)Body>Front Door Wire LH / Television Camera Wire>Outer Rear View Mirror Assembly LH

Click Connector(O101)Body>Floor Wire>Rear Combination Light Assembly LH

Click Connector(H7)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

B14-1 (B) - Body ground Always 10 kΩ or higher
L12-10 (B) - Body ground Always 10 kΩ or higher
O101-1 (B) - Body ground Always 10 kΩ or higher
H7-1 (LL) - Body ground Always 10 kΩ or higher
H7-5 (TRNL) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the B14 daytime running light assembly LH connector.


b.

Disconnect the L8 outer rear view mirror assembly LH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B14,L8,O101,H7)Location & Routing

Click Connector(B14)Engine Compartment>No. 3 Engine Room Wire>Daytime Running Light Assembly LH

Click Connector(L8)Body>Front Door Wire LH / Television Camera Wire>Outer Rear View Mirror Assembly LH

Click Connector(O101)Body>Floor Wire>Rear Combination Light Assembly LH

Click Connector(H7)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

B14-1 (B) - Body ground Always 10 kΩ or higher
L8-16 (B) - Body ground Always 10 kΩ or higher
O101-1 (B) - Body ground Always 10 kΩ or higher
H7-1 (LL) - Body ground Always 10 kΩ or higher
H7-5 (TRNL) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK LH SIDE TURN SIGNAL LIGHTS (FRONT TURN SIGNAL LIGHT CIRCUIT)

Pre-procedure1

a.

Disconnect the B14 daytime running light assembly LH connector.


Procedure1

a.

Operate the turn signal switch and check that the LH side turn signal lights other than the front turn signal light blink.

HINT:

If the LH side turn signal lights other than the front turn signal light blink, the daytime running light assembly LH is malfunctioning.


Result:
Result Proceed to
LH side turn signal lights other than the front turn signal light blink A
All LH side turn signal lights do not blink B



Post-procedure1

a.

None



A

REPLACE DAYTIME RUNNING LIGHT ASSEMBLY LH

B

12.CHECK LH SIDE TURN SIGNAL LIGHTS (SIDE TURN SIGNAL LIGHT CIRCUIT)
12.CHECK LH SIDE TURN SIGNAL LIGHTS (SIDE TURN SIGNAL LIGHT CIRCUIT)

Pre-procedure1

a.

Connect the daytime running light assembly LH connector.


b.

Disconnect the L10*1, L12*2 or L8*3 outer rear view mirror assembly LH connector.

*1: w/o Mirror Heater

*2: w/o Panoramic View Monitor System with Mirror Heater

*3: w/ Panoramic View Monitor System with Mirror Heater



Procedure1

a.

Operate the turn signal switch and check that the LH side turn signal lights other than the side turn signal light blink.

HINT:

If the LH side turn signal lights other than the side turn signal light blink, a component of the outer rear view mirror assembly LH is malfunctioning.


Result:
Result Proceed to
LH side turn signal lights other than the side turn signal light blink A
All LH side turn signal lights do not blink B



Post-procedure1

a.

None



A

13.CHECK LH SIDE TURN SIGNAL LIGHTS (OUTER REAR VIEW MIRROR ASSEMBLY LH)

B

14.CHECK LH SIDE TURN SIGNAL LIGHTS (REAR TURN SIGNAL LIGHT CIRCUIT)
13.CHECK LH SIDE TURN SIGNAL LIGHTS (OUTER REAR VIEW MIRROR ASSEMBLY LH)

Pre-procedure1

a.

Remove the side turn signal light assembly LH from outer rear view mirror assembly LH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL



b.

Connect the outer rear view mirror assembly LH connector.


Procedure1

a.

Operate the turn signal switch and check that the LH side turn signal lights other than the side turn signal light blink.

HINT:

If all LH side turn signal lights do not blink, the outer rear view mirror assembly LH is malfunctioning.


Result:
Result Proceed to
LH side turn signal lights other than the side turn signal light blink A
All LH side turn signal lights do not blink B



Post-procedure1

a.

None



A

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY LH

B

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

14.CHECK LH SIDE TURN SIGNAL LIGHTS (REAR TURN SIGNAL LIGHT CIRCUIT)

Pre-procedure1

a.

Connect the outer rear view mirror assembly LH connector.


b.

Disconnect the O107 rear combination light assembly LH connector.


c.

Disconnect the Y12 rear light assembly LH connector.


Procedure1

a.

Operate the turn signal switch and check that the LH side turn signal lights other than the rear turn signal light blink.

HINT:

If the LH side turn signal lights other than the rear turn signal light blink, the rear combination light assembly LH or rear light assembly LH is malfunctioning.


Result:
Result Proceed to
LH side turn signal lights other than the rear turn signal light blink A
All LH side turn signal lights do not blink B



Post-procedure1

a.

None



A

15.INSPECT REAR COMBINATION LIGHT ASSEMBLY LH

B

17.CHECK VEHICLE TYPE
15.INSPECT REAR COMBINATION LIGHT ASSEMBLY LH

OK

16.INSPECT REAR LIGHT ASSEMBLY LH

NG

16.INSPECT REAR LIGHT ASSEMBLY LH

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

17.CHECK VEHICLE TYPE
a.

Check vehicle condition.

Result:
Result Proceed to
w/o Mirror Heater A
w/o Panoramic View Monitor System with Mirror Heater B
w/ Panoramic View Monitor System with Mirror Heater C




A

18.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

B

19.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

C

20.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)
18.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the B12 daytime running light assembly LH connector.


b.

Disconnect the L10 outer rear view mirror assembly LH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B12,L10,O107,Y12,H7)Location & Routing

Click Connector(B12)Engine Compartment>No. 3 Engine Room Wire>Daytime Running Light Assembly LH

Click Connector(L10)Body>Front Door Wire LH / Television Camera Wire>Outer Rear View Mirror Assembly LH

Click Connector(O107)Body>Floor Wire>Rear Combination Light Assembly LH

Click Connector(Y12)Body>No. 2 Back Door Wire>Rear Light Assembly LH

Click Connector(H7)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

B12-3 (B) - Body ground Always 10 kΩ or higher
L10-4 (B) - Body ground Always 10 kΩ or higher
O107-2 (B) - Body ground Always 10 kΩ or higher
Y12-4 (TRN) - Body ground Always 10 kΩ or higher
H7-1 (LL) - Body ground Always 10 kΩ or higher
H7-5 (TRNL) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the B12 daytime running light assembly LH connector.


b.

Disconnect the L12 outer rear view mirror assembly LH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B12,L12,O107,Y12,H7)Location & Routing

Click Connector(B12)Engine Compartment>No. 3 Engine Room Wire>Daytime Running Light Assembly LH

Click Connector(L12)Body>Front Door Wire LH / Television Camera Wire>Outer Rear View Mirror Assembly LH

Click Connector(O107)Body>Floor Wire>Rear Combination Light Assembly LH

Click Connector(Y12)Body>No. 2 Back Door Wire>Rear Light Assembly LH

Click Connector(H7)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

B12-3 (B) - Body ground Always 10 kΩ or higher
L12-10 (B) - Body ground Always 10 kΩ or higher
O107-2 (B) - Body ground Always 10 kΩ or higher
Y12-4 (TRN) - Body ground Always 10 kΩ or higher
H7-1 (LL) - Body ground Always 10 kΩ or higher
H7-5 (TRNL) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the B12 daytime running light assembly LH connector.


b.

Disconnect the L8 outer rear view mirror assembly LH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B12,L8,O107,Y12,H7)Location & Routing

Click Connector(B12)Engine Compartment>No. 3 Engine Room Wire>Daytime Running Light Assembly LH

Click Connector(L8)Body>Front Door Wire LH / Television Camera Wire>Outer Rear View Mirror Assembly LH

Click Connector(O107)Body>Floor Wire>Rear Combination Light Assembly LH

Click Connector(Y12)Body>No. 2 Back Door Wire>Rear Light Assembly LH

Click Connector(H7)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

B12-3 (B) - Body ground Always 10 kΩ or higher
L8-16 (B) - Body ground Always 10 kΩ or higher
O107-2 (B) - Body ground Always 10 kΩ or higher
Y12-4 (TRN) - Body ground Always 10 kΩ or higher
H7-1 (LL) - Body ground Always 10 kΩ or higher
H7-5 (TRNL) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK VEHICLE TYPE
a.

Check vehicle condition.

Result:
Result Proceed to
for Halogen Headlight and Rear Turn Signal Light Bulb Type A
for LED Headlight and Rear Turn Signal Light LED Type B




A

22.CHECK RH SIDE TURN SIGNAL LIGHTS (FRONT TURN SIGNAL LIGHT CIRCUIT)

B

30.CHECK RH SIDE TURN SIGNAL LIGHTS (FRONT TURN SIGNAL LIGHT CIRCUIT)
22.CHECK RH SIDE TURN SIGNAL LIGHTS (FRONT TURN SIGNAL LIGHT CIRCUIT)

Pre-procedure1

a.

Disconnect the B15 daytime running light assembly RH connector.


Procedure1

a.

Operate the turn signal switch and check that the RH side turn signal lights other than the front turn signal light blink.

HINT:

If the RH side turn signal lights other than the front turn signal light blink, the daytime running light assembly RH is malfunctioning.


Result:
Result Proceed to
LH side turn signal lights other than the front turn signal light blink A
All LH side turn signal lights do not blink B



Post-procedure1

a.

None



A

REPLACE FRONT TURN SIGNAL LIGHT SOCKET

B

23.CHECK RH SIDE TURN SIGNAL LIGHTS (SIDE TURN SIGNAL LIGHT CIRCUIT)
23.CHECK RH SIDE TURN SIGNAL LIGHTS (SIDE TURN SIGNAL LIGHT CIRCUIT)

Pre-procedure1

a.

Connect the daytime running light assembly RH connector.


b.

Disconnect the K10*1, K13*2 or K8*3 outer rear view mirror assembly RH connector.

*1: w/o Mirror Heater

*2: w/o Panoramic View Monitor System with Mirror Heater

*3: w/ Panoramic View Monitor System with Mirror Heater



Procedure1

a.

Operate the turn signal switch and check that the RH side turn signal lights other than the side turn signal light blink.

HINT:

If the RH side turn signal lights other than the side turn signal light blink, a component of the outer rear view mirror assembly RH is malfunctioning.


Result:
Result Proceed to
RH side turn signal lights other than the side turn signal light blink A
All RH side turn signal lights do not blink B



Post-procedure1

a.

None



A

24.CHECK RH SIDE TURN SIGNAL LIGHTS (OUTER REAR VIEW MIRROR ASSEMBLY RH)

B

25.CHECK RH SIDE TURN SIGNAL LIGHTS (REAR TURN SIGNAL LIGHT CIRCUIT)
24.CHECK RH SIDE TURN SIGNAL LIGHTS (OUTER REAR VIEW MIRROR ASSEMBLY RH)

Pre-procedure1

a.

Remove the side turn signal light assembly RH from outer rear view mirror assembly RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL



b.

Connect the outer rear view mirror assembly RH connector.


Procedure1

a.

Operate the turn signal switch and check that the RH side turn signal lights other than the side turn signal light blink.

HINT:

If all RH side turn signal lights do not blink, the outer rear view mirror assembly RH is malfunctioning.


Result:
Result Proceed to
RH side turn signal lights other than the side turn signal light blink A
All RH side turn signal lights do not blink B



Post-procedure1

a.

None



A

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY RH

B

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

25.CHECK RH SIDE TURN SIGNAL LIGHTS (REAR TURN SIGNAL LIGHT CIRCUIT)

Pre-procedure1

a.

Connect the outer rear view mirror assembly RH connector.


b.

Disconnect the O103 rear combination light assembly RH connector.


Procedure1

a.

Operate the turn signal switch and check that the RH side turn signal lights other than the rear turn signal light blink.

HINT:

If the RH side turn signal lights other than the rear turn signal light blink, the rear combination light cord RH is malfunctioning.


Result:
Result Proceed to
RH side turn signal lights other than the rear turn signal light blink A
All RH side turn signal lights do not blink B



Post-procedure1

a.

None



A

REPLACE REAR TURN SIGNAL LIGHT SOCKET

B

26.CHECK VEHICLE TYPE
26.CHECK VEHICLE TYPE
a.

Check vehicle condition.

Result:
Result Proceed to
w/o Mirror Heater A
w/o Panoramic View Monitor System with Mirror Heater B
w/ Panoramic View Monitor System with Mirror Heater C




A

27.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

B

28.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

C

29.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)
27.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the B15 daytime running light assembly RH connector.


b.

Disconnect the K10 outer rear view mirror assembly RH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B15,K10,O103,H7)Location & Routing

Click Connector(B15)Engine Compartment>No. 3 Engine Room Wire>Daytime Running Light Assembly RH

Click Connector(K10)Body>Front Door Wire RH / Television Camera Wire>Outer Rear View Mirror Assembly RH

Click Connector(O103)Body>Floor Wire>Rear Combination Light Assembly RH

Click Connector(H7)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

B15-1 (B) - Body ground Always 10 kΩ or higher
K10-4 (B) - Body ground Always 10 kΩ or higher
O103-1 (B) - Body ground Always 10 kΩ or higher
H7-2 (LR) - Body ground Always 10 kΩ or higher
H7-6 (TRNR) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

28.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the B15 daytime running light assembly RH connector.


b.

Disconnect the K13 outer rear view mirror assembly RH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B15,K13,O103,H7)Location & Routing

Click Connector(B15)Engine Compartment>No. 3 Engine Room Wire>Daytime Running Light Assembly RH

Click Connector(K13)Body>Front Door Wire RH / Television Camera Wire>Outer Rear View Mirror Assembly RH

Click Connector(O103)Body>Floor Wire>Rear Combination Light Assembly RH

Click Connector(H7)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

B15-1 (B) - Body ground Always 10 kΩ or higher
K13-10 (B) - Body ground Always 10 kΩ or higher
O103-1 (B) - Body ground Always 10 kΩ or higher
H7-2 (LR) - Body ground Always 10 kΩ or higher
H7-6 (TRNR) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

29.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the B15 daytime running light assembly RH connector.


b.

Disconnect the K8 outer rear view mirror assembly RH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B15,K8,O103,H7)Location & Routing

Click Connector(B15)Engine Compartment>No. 3 Engine Room Wire>Daytime Running Light Assembly RH

Click Connector(K8)Body>Front Door Wire RH / Television Camera Wire>Outer Rear View Mirror Assembly RH

Click Connector(O103)Body>Floor Wire>Rear Combination Light Assembly RH

Click Connector(H7)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

B15-1 (B) - Body ground Always 10 kΩ or higher
K8-16 (B) - Body ground Always 10 kΩ or higher
O103-1 (B) - Body ground Always 10 kΩ or higher
H7-2 (LR) - Body ground Always 10 kΩ or higher
H7-6 (TRNR) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

30.CHECK RH SIDE TURN SIGNAL LIGHTS (FRONT TURN SIGNAL LIGHT CIRCUIT)

Pre-procedure1

a.

Disconnect the B15 daytime running light assembly RH connector.


Procedure1

a.

Operate the turn signal switch and check that the RH side turn signal lights other than the front turn signal light blink.

HINT:

If the RH side turn signal lights other than the front turn signal light blink, the daytime running light assembly RH is malfunctioning.


Result:
Result Proceed to
LH side turn signal lights other than the front turn signal light blink A
All LH side turn signal lights do not blink B



Post-procedure1

a.

None



A

REPLACE DAYTIME RUNNING LIGHT ASSEMBLY RH

B

31.CHECK RH SIDE TURN SIGNAL LIGHTS (SIDE TURN SIGNAL LIGHT CIRCUIT)
31.CHECK RH SIDE TURN SIGNAL LIGHTS (SIDE TURN SIGNAL LIGHT CIRCUIT)

Pre-procedure1

a.

Connect the headlight assembly RH connector.


b.

Disconnect the K10*1, K13*2 or K8*3 outer rear view mirror assembly RH connector.

*1: w/o Mirror Heater

*2: w/o Panoramic View Monitor System with Mirror Heater

*3: w/ Panoramic View Monitor System with Mirror Heater



Procedure1

a.

Operate the turn signal switch and check that the RH side turn signal lights other than the side turn signal light blink.

HINT:

If the RH side turn signal lights other than the side turn signal light blink, a component of the outer rear view mirror assembly RH is malfunctioning.


Result:
Result Proceed to
RH side turn signal lights other than the side turn signal light blink A
All RH side turn signal lights do not blink B



Post-procedure1

a.

None



A

32.CHECK RH SIDE TURN SIGNAL LIGHTS (OUTER REAR VIEW MIRROR ASSEMBLY RH)

B

33.CHECK RH SIDE TURN SIGNAL LIGHTS (REAR TURN SIGNAL LIGHT CIRCUIT)
32.CHECK RH SIDE TURN SIGNAL LIGHTS (OUTER REAR VIEW MIRROR ASSEMBLY RH)

Pre-procedure1

a.

Remove the side turn signal light assembly RH from outer rear view mirror assembly RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL



b.

Connect the outer rear view mirror assembly RH connector.


Procedure1

a.

Operate the turn signal switch and check that the RH side turn signal lights other than the side turn signal light blink.

HINT:

If all RH side turn signal lights do not blink, the outer rear view mirror assembly RH is malfunctioning.


Result:
Result Proceed to
RH side turn signal lights other than the side turn signal light blink A
All RH side turn signal lights do not blink B



Post-procedure1

a.

None



A

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY RH

B

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

33.CHECK RH SIDE TURN SIGNAL LIGHTS (REAR TURN SIGNAL LIGHT CIRCUIT)

Pre-procedure1

a.

Connect the outer rear view mirror assembly RH connector.


b.

Disconnect the O110 rear combination light assembly RH connector.


c.

Disconnect the Y14 rear light assembly RH connector.


Procedure1

a.

Operate the turn signal switch and check that the RH side turn signal lights other than the rear turn signal light blink.

HINT:

If the RH side turn signal lights other than the rear turn signal light blink, the rear combination light cord RH is malfunctioning.


Result:
Result Proceed to
RH side turn signal lights other than the rear turn signal light blink A
All RH side turn signal lights do not blink B



Post-procedure1

a.

None



A

34.INSPECT REAR COMBINATION LIGHT ASSEMBLY RH

B

36.CHECK VEHICLE TYPE
34.INSPECT REAR COMBINATION LIGHT ASSEMBLY RH

OK

35.INSPECT REAR LIGHT ASSEMBLY RH

NG

35.INSPECT REAR LIGHT ASSEMBLY RH

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

36.CHECK VEHICLE TYPE
a.

Check vehicle condition.

Result:
Result Proceed to
w/o Mirror Heater A
w/o Panoramic View Monitor System with Mirror Heater B
w/ Panoramic View Monitor System with Mirror Heater C




A

37.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

B

38.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

C

39.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)
37.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the B13 daytime running light assembly RH connector.


b.

Disconnect the K10 outer rear view mirror assembly RH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B13,K10,O110,Y14,H7)Location & Routing

Click Connector(B13)Engine Compartment>No. 3 Engine Room Wire>Daytime Running Light Assembly RH

Click Connector(K10)Body>Front Door Wire RH / Television Camera Wire>Outer Rear View Mirror Assembly RH

Click Connector(O110)Body>Floor Wire>Rear Combination Light Assembly RH

Click Connector(Y14)Body>No. 2 Back Door Wire>Rear Light Assembly RH

Click Connector(H7)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

B13-3 (B) - Body ground Always 10 kΩ or higher
K10-4 (B) - Body ground Always 10 kΩ or higher
O110-2 (B) - Body ground Always 10 kΩ or higher
Y14-4 (TRN) - Body ground Always 10 kΩ or higher
H7-2 (LR) - Body ground Always 10 kΩ or higher
H7-6 (TRNR) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

38.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the B13 daytime running light assembly RH connector.


b.

Disconnect the K13 outer rear view mirror assembly RH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B13,K13,O110,Y14,H7)Location & Routing

Click Connector(B13)Engine Compartment>No. 3 Engine Room Wire>Daytime Running Light Assembly RH

Click Connector(K13)Body>Front Door Wire RH / Television Camera Wire>Outer Rear View Mirror Assembly RH

Click Connector(O110)Body>Floor Wire>Rear Combination Light Assembly RH

Click Connector(Y14)Body>No. 2 Back Door Wire>Rear Light Assembly RH

Click Connector(H7)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

B13-3 (B) - Body ground Always 10 kΩ or higher
K13-10 (B) - Body ground Always 10 kΩ or higher
O110-2 (B) - Body ground Always 10 kΩ or higher
Y14-4 (TRN) - Body ground Always 10 kΩ or higher
H7-2 (LR) - Body ground Always 10 kΩ or higher
H7-6 (TRNR) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

39.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the B13 daytime running light assembly RH connector.


b.

Disconnect the K8 outer rear view mirror assembly RH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B13,K8,O110,Y14,H7)Location & Routing

Click Connector(B13)Engine Compartment>No. 3 Engine Room Wire>Daytime Running Light Assembly RH

Click Connector(K8)Body>Front Door Wire RH / Television Camera Wire>Outer Rear View Mirror Assembly RH

Click Connector(O110)Body>Floor Wire>Rear Combination Light Assembly RH

Click Connector(Y14)Body>No. 2 Back Door Wire>Rear Light Assembly RH

Click Connector(H7)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

B13-3 (B) - Body ground Always 10 kΩ or higher
K8-16 (B) - Body ground Always 10 kΩ or higher
O110-2 (B) - Body ground Always 10 kΩ or higher
Y14-4 (TRN) - Body ground Always 10 kΩ or higher
H7-2 (LR) - Body ground Always 10 kΩ or higher
H7-6 (TRNR) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR