Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2020.08–2021.07
RM3700E _58 Vehicle Interior _093087 METER / GAUGE / DISPLAY _0438738 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B150718  Turn Signal Light Circuit Current Below Threshold  


DESCRIPTION

This DTC is stored when the combination meter assembly detects an open in a front turn signal light circuit or rear turn signal light circuit.

HINT:
·

If there is an open in a front turn signal light circuit or rear turn signal light circuit, the turn signal lights on the side with the open circuit will blink faster than usual.

·

If there is an open in a side turn signal light circuit, DTC B150718 will not be stored.



DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B150718 Turn Signal Light Circuit Current Below Threshold Diagnosis Condition:

Auxiliary battery voltage is 10 V or more


Malfunction Status:
·

Open in front turn signal light circuit

·

Open in rear turn signal light circuit


·

for Front Turn Signal Light:

-

Front turn signal light socket*1

-

Front turn signal light bulb*1

-

Daytime running light assembly LH*2

-

Daytime running light assembly RH*2


·

for Rear Turn Signal Light:

-

Rear turn signal light socket*3

-

Rear turn signal light bulb*3

-

Rear combination light assembly LH*4

-

Rear combination light assembly RH*4

-

Rear light assembly LH*4

-

Rear light assembly RH*4


·

Wire harness or connector

·

Combination meter assembly


Combination Meter A

*1: for Halogen Headlight

*2: for LED Headlight

*3: for Rear Turn Signal Light Bulb Type

*4: for Rear Turn Signal Light LED Type


WIRING DIAGRAM

E450263E03
0.167,0.167 1.563,0.625 1.396,0.458 12 false for LH Side: 0.5,2.406 2.917,2.74 2.417,0.333 10 false Daytime Running Light Assembly LH*1 0.5,2.219 1.01,2.396 0.51,0.177 10 false B14 1.146,1.792 3.896,2.125 2.75,0.333 10 false Front Turn Signal Light Socket 0.5,4.188 2.917,4.521 2.417,0.333 10 false Daytime Running Light Assembly LH*2 0.5,4.01 1.01,4.188 0.51,0.177 10 false B12 3.844,1.115 4.156,1.313 0.313,0.198 10 false *1 3.844,3.115 4.156,3.313 0.313,0.198 10 false *2 0.146,5.083 2.5,5.417 2.354,0.333 10 false *1: for Halogen Headlight 0.146,5.417 2.5,5.75 2.354,0.333 10 false *2: for LED Headlight 5.115,4.833 5.427,5.031 0.313,0.198 10 false H7 5.104,5 6.948,5.333 1.844,0.333 10 false Combination Meter Assembly 5.979,2.75 6.969,3.125 0.99,0.375 10 false FLASHER IC 5.063,1.125 5.375,1.323 0.313,0.198 10 false LL 4.844,1.125 5,1.323 0.156,0.198 10 false 1 2.938,1.125 3.094,1.323 0.156,0.198 10 false B 2.938,1.427 3.094,1.625 0.156,0.198 10 false E 2.948,3.083 3.104,3.281 0.156,0.198 10 false B 2.948,3.427 3.104,3.625 0.156,0.198 10 false E 3.146,1.125 3.302,1.323 0.156,0.198 10 false 1 3.156,1.417 3.313,1.615 0.156,0.198 10 false 2 3.156,3.406 3.313,3.604 0.156,0.198 10 false 1 3.156,3.104 3.313,3.302 0.156,0.198 10 false 3

E450265E07
0.177,0.167 1.479,0.625 1.302,0.458 12 false for LH Side: 1.281,1.917 3.719,2.25 2.438,0.333 10 false Rear Turn Signal Light Socket 5.052,1.25 5.667,1.448 0.615,0.198 10 false TRNL 5.938,1.688 6.844,2.052 0.906,0.365 10 false FLASHER IC 5.99,3.792 6.604,4.135 0.615,0.344 10 false TURN L 4.823,1.25 4.979,1.448 0.156,0.198 10 false 5 0.583,2.51 3.229,2.917 2.646,0.406 10 false Rear Combination Light Assembly LH*1 0.583,2.333 1.198,2.531 0.615,0.198 10 false O101 3.052,1.25 3.208,1.448 0.156,0.198 10 false B 3.063,1.552 3.219,1.75 0.156,0.198 10 false E 3.292,1.25 3.448,1.448 0.156,0.198 10 false 1 3.292,1.552 3.448,1.75 0.156,0.198 10 false 2 3.281,3.427 3.438,3.625 0.156,0.198 10 false 2 0.813,3.427 0.969,3.625 0.156,0.198 10 false 1 0.885,4.458 3.552,4.875 2.667,0.417 10 false Rear Combination Light Assembly LH*2 0.885,4.281 1.5,4.479 0.615,0.198 10 false O107 1.292,6.427 3.771,6.792 2.479,0.365 10 false Rear Light Assembly LH*2 1.292,6.24 1.75,6.438 0.458,0.198 10 false Y12 3.063,3.542 3.219,3.74 0.156,0.198 10 false B 1.021,3.542 1.177,3.74 0.156,0.198 10 false E 1.031,5.927 1.188,6.125 0.156,0.198 10 false E 2.885,5.906 3.344,6.104 0.458,0.198 10 false TRN 1.01,5.49 1.625,5.688 0.615,0.198 10 false TRN4 1.01,3.948 1.625,4.146 0.615,0.198 10 false TRN4 0.802,3.844 0.958,4.042 0.156,0.198 10 false 4 0.802,5.375 0.958,5.573 0.156,0.198 10 false 1 0.802,5.792 0.958,5.99 0.156,0.198 10 false 2 3.271,5.792 3.427,5.99 0.156,0.198 10 false 4 4.031,1.25 4.344,1.448 0.313,0.198 10 false *1 4.458,1.75 4.771,1.948 0.313,0.198 10 false *2 5.073,6.417 5.385,6.615 0.313,0.198 10 false H7 5.063,6.583 6.917,7 1.854,0.417 10 false Combination Meter Assembly 0.167,7.083 3.667,7.417 3.5,0.333 10 false *1: for Rear Turn Signal Light Bulb Type 0.167,7.417 3.5,7.75 3.333,0.333 10 false *2: for Rear Turn Signal Light LED Type

E450263E04
0.167,0.167 1.583,0.656 1.417,0.49 12 false for RH Side: 0.5,2.406 3.083,2.771 2.583,0.365 10 false Daytime Running Light Assembly RH*1 0.5,2.219 1.01,2.396 0.51,0.177 10 false B15 1.146,1.792 3.896,2.125 2.75,0.333 10 false Front Turn Signal Light Socket 0.5,4.188 2.99,4.552 2.49,0.365 10 false Daytime Running Light Assembly RH*2 0.5,4.01 1.01,4.188 0.51,0.177 10 false B13 3.844,1.115 4.156,1.313 0.313,0.198 10 false *1 3.844,3.115 4.156,3.313 0.313,0.198 10 false *2 0.146,5.083 2.5,5.417 2.354,0.333 10 false *1: for Halogen Headlight 0.146,5.417 2.5,5.75 2.354,0.333 10 false *2: for LED Headlight 5.094,4.823 5.406,5.021 0.313,0.198 10 false H7 5.094,5 7.031,5.344 1.938,0.344 10 false Combination Meter Assembly 5.969,2.75 6.958,3.125 0.99,0.375 10 false FLASHER IC 5.063,1.125 5.375,1.323 0.313,0.198 10 false LR 4.844,1.125 5,1.323 0.156,0.198 10 false 2 2.938,1.125 3.094,1.323 0.156,0.198 10 false B 2.938,1.427 3.094,1.625 0.156,0.198 10 false E 2.948,3.083 3.104,3.281 0.156,0.198 10 false B 2.948,3.427 3.104,3.625 0.156,0.198 10 false E 3.156,1.125 3.313,1.323 0.156,0.198 10 false 1 3.156,1.417 3.313,1.615 0.156,0.198 10 false 2 3.156,3.406 3.313,3.604 0.156,0.198 10 false 1 3.156,3.104 3.313,3.302 0.156,0.198 10 false 3

E450265E08
0.177,0.167 1.219,0.5 1.042,0.333 12 false for RH Side: 1.281,1.917 3.719,2.25 2.438,0.333 10 false Rear Turn Signal Light Socket 5.052,1.25 5.667,1.448 0.615,0.198 10 false TRNR 5.938,1.688 6.844,2.052 0.906,0.365 10 false FLASHER IC 5.99,3.792 6.604,4.135 0.615,0.344 10 false TURN R 4.823,1.25 4.979,1.448 0.156,0.198 10 false 6 0.75,2.51 3.417,2.906 2.667,0.396 10 false Rear Combination Light Assembly RH*1 0.75,2.333 1.365,2.531 0.615,0.198 10 false O103 3.052,1.25 3.208,1.448 0.156,0.198 10 false B 3.063,1.552 3.219,1.75 0.156,0.198 10 false E 3.292,1.25 3.448,1.448 0.156,0.198 10 false 1 3.292,1.552 3.448,1.75 0.156,0.198 10 false 2 3.281,3.427 3.438,3.625 0.156,0.198 10 false 2 0.813,3.427 0.969,3.625 0.156,0.198 10 false 1 1.031,4.458 3.594,4.844 2.563,0.385 10 false Rear Combination Light Assembly RH*2 1.031,4.281 1.646,4.479 0.615,0.198 10 false O110 1.25,6.427 3.729,6.792 2.479,0.365 10 false Rear Light Assembly RH*2 1.25,6.24 1.708,6.438 0.458,0.198 10 false Y14 3.063,3.542 3.219,3.74 0.156,0.198 10 false B 1.021,3.542 1.177,3.74 0.156,0.198 10 false E 1.031,5.927 1.188,6.125 0.156,0.198 10 false E 2.885,5.906 3.344,6.104 0.458,0.198 10 false TRN 1.01,5.49 1.625,5.688 0.615,0.198 10 false TRN4 1.01,3.948 1.625,4.146 0.615,0.198 10 false TRN4 0.802,3.844 0.958,4.042 0.156,0.198 10 false 4 0.802,5.375 0.958,5.573 0.156,0.198 10 false 1 0.802,5.792 0.958,5.99 0.156,0.198 10 false 2 3.271,5.792 3.427,5.99 0.156,0.198 10 false 4 4.031,1.25 4.344,1.448 0.313,0.198 10 false *1 4.458,1.75 4.771,1.948 0.313,0.198 10 false *2 5.094,6.417 5.406,6.615 0.313,0.198 10 false H7 5.073,6.583 6.958,7.063 1.885,0.479 10 false Combination Meter Assembly 0.167,7.083 3.667,7.417 3.5,0.333 10 false *1: for Rear Turn Signal Light Bulb Type 0.167,7.417 3.5,7.75 3.333,0.333 10 false *2: for Rear Turn Signal Light LED Type

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

Inspect the turn signal light bulbs before performing the following procedure.



PROCEDURE

1.CHECK SYMPTOMS
a.

Check the problem symptoms.


Result:
Result Proceed to
LH side front turn signal light does not blink A
LH side rear turn signal light does not blink B
RH side front turn signal light does not blink C
RH side rear turn signal light does not blink D



A

2.CHECK VEHICLE TYPE

B

7.CHECK VEHICLE TYPE

C

19.CHECK VEHICLE TYPE

D

24.CHECK VEHICLE TYPE
2.CHECK VEHICLE TYPE
a.

Check vehicle condition.

Result:
Result Proceed to
for Halogen Headlight A
for LED Headlight B




A

3.CHECK LH SIDE FRONT TURN SIGNAL LIGHT (FRONT TURN SIGNAL LIGHT SOCKET)

B

5.CHECK LH SIDE FRONT TURN SIGNAL LIGHT (DAYTIME RUNNING LIGHT ASSEMBLY LH)
3.CHECK LH SIDE FRONT TURN SIGNAL LIGHT (FRONT TURN SIGNAL LIGHT SOCKET)

Pre-procedure1

a.

Interchange the front turn signal light socket LH with RH and connect the connectors.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>FRONT TURN SIGNAL LIGHT BULB>REMOVAL



Procedure1

a.

Operate the turn signal switch and check that the LH side front turn signal light operates normally.

HINT:

If the LH side front turn signal light operates normally, the front turn signal light socket is malfunctioning.


Result:
Result Proceed to
LH side front turn signal light operates normally A
LH side front turn signal light does not blink B



Post-procedure1

a.

None



A

REPLACE FRONT TURN SIGNAL LIGHT SOCKET

B

4.CHECK HARNESS AND CONNECTOR (DAYTIME RUNNING LIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (DAYTIME RUNNING LIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the B14 daytime running light assembly LH connector.


b.

Disconnect the H7 combination meter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B14,H7)Location & Routing

Click Connector(B14)Engine Compartment>No. 3 Engine Room Wire>Daytime Running Light Assembly LH

Click Connector(H7)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

B14-1 (B) - H7-1 (LL) Always Below 1 Ω
B14-2 (E) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK LH SIDE FRONT TURN SIGNAL LIGHT (DAYTIME RUNNING LIGHT ASSEMBLY LH)

Pre-procedure1

a.

Interchange the daytime running light assembly LH with RH and connect the connectors.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>DAYTIME RUNNING LIGHT ASSEMBLY>REMOVAL



Procedure1

a.

Operate the turn signal switch and check that the LH side front turn signal light operates normally.

HINT:

If the RH side front turn signal light operates normally, the daytime running light assembly LH is malfunctioning.


Result:
Result Proceed to
LH side front turn signal light operates normally A
LH side front turn signal light does not blink B



Post-procedure1

a.

None



A

REPLACE DAYTIME RUNNING LIGHT ASSEMBLY LH

B

6.CHECK HARNESS AND CONNECTOR (DAYTIME RUNNING LIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
6.CHECK HARNESS AND CONNECTOR (DAYTIME RUNNING LIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the B12 daytime running light assembly LH connector.


b.

Disconnect the H7 combination meter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B12,H7)Location & Routing

Click Connector(B12)Engine Compartment>No. 3 Engine Room Wire>Daytime Running Light Assembly LH

Click Connector(H7)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

B12-3 (B) - H7-1 (LL) Always Below 1 Ω
B12-2 (E) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK VEHICLE TYPE
a.

Check vehicle condition.

Result:
Result Proceed to
for Rear Turn Signal Light Bulb Type A
for Rear Turn Signal Light LED Type B




A

8.CHECK LH SIDE REAR TURN SIGNAL LIGHT (REAR TURN SIGNAL LIGHT SOCKET)

B

10.INSPECT LIGHTS
8.CHECK LH SIDE REAR TURN SIGNAL LIGHT (REAR TURN SIGNAL LIGHT SOCKET)

Pre-procedure1

a.

Interchange the rear turn signal light socket LH with RH and connect the connectors.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>REAR TURN SIGNAL LIGHT BULB>REMOVAL



Procedure1

a.

Operate the turn signal switch and check that the LH side rear turn signal light operates normally.

HINT:

If the LH side rear turn signal lights operates normally, the rear turn signal light socket is malfunctioning.


Result:
Result Proceed to
LH side rear turn signal lights operates normally A
LH side rear turn signal light does not blink B



Post-procedure1

a.

None



A

REPLACE REAR TURN SIGNAL LIGHT SOCKET

B

9.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
9.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the O101 rear combination light assembly LH connector.


b.

Disconnect the H7 combination meter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O101,H7)Location & Routing

Click Connector(O101)Body>Floor Wire>Rear Combination Light Assembly LH

Click Connector(H7)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

O101-1 (B) - H7-5 (TRNL) Always Below 1 Ω
O101-2 (E) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT LIGHTS
a.

Inspect the illumination of each turn signal light.

Result:
Result Proceed to
All LH side rear turn signal lights do not blink. A
Rear light assembly LH does not illuminate B
Rear combination light assembly LH does not illuminate. C




A

11.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY LH AND REAR COMBINATION LIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

B

15.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

C

17.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
11.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY LH AND REAR COMBINATION LIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the Y12 rear light assembly LH connector.


b.

Disconnect the O107 rear combination light assembly LH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Rear light assembly LH
Tester Connection Condition Specified Condition

Click Location & Routing(Y12,H7)Location & Routing

Click Connector(Y12)Body>No. 2 Back Door Wire>Rear Light Assembly LH

Click Connector(H7)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

Y12-4 (TRN) - H7-5 (TRNL) Always Below 1 Ω
Y12-2 (E) - Body ground Always Below 1 Ω
Y12-4 (TRN) or H7-5 (TRNL) - Body ground Always Below 1 Ω

Rear combination light assembly LH
Tester Connection Condition Specified Condition

Click Location & Routing(O107,H7)Location & Routing

Click Connector(O107)Body>Floor Wire>Rear Combination Light Assembly LH

Click Connector(H7)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

O107-2 (B) - H7-5 (TRNL) Always Below 1 Ω
O107-1 (E) - Body ground Always Below 1 Ω
O107-2 (B) or H7-5 (TRNL) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

12.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY LH AND REAR COMBINATION LIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY LH AND REAR COMBINATION LIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Y12,O107)Location & Routing

Click Connector(Y12)Body>No. 2 Back Door Wire>Rear Light Assembly LH

Click Connector(O107)Body>Floor Wire>Rear Combination Light Assembly LH

Y12-1 (TRN4) - O107-4 (TRN4) Always Below 1 Ω
Y12-1 (TRN4) or O107-4 (TRN4) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

13.INSPECT REAR LIGHT ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT REAR LIGHT ASSEMBLY LH

OK

14.INSPECT REAR COMBINATION LIGHT ASSEMBLY LH

NG

14.INSPECT REAR COMBINATION LIGHT ASSEMBLY LH

OK

REPLACE COMBINATION METER ASSEMBLY

NG

15.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the Y12 rear light assembly LH connector.


b.

Disconnect the O107 rear combination light assembly LH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Y12,H7)Location & Routing

Click Connector(Y12)Body>No. 2 Back Door Wire>Rear Light Assembly LH

Click Connector(H7)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

Y12-4 (TRN) - H7-5 (TRNL) Always Below 1 Ω
Y12-2 (E) - Body ground Always Below 1 Ω
Y12-4 (TRN) or H7-5 (TRNL) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

16.INSPECT REAR LIGHT ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.INSPECT REAR LIGHT ASSEMBLY LH

OK

REPLACE COMBINATION METER ASSEMBLY

NG

17.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the O107 rear combination light assembly LH connector.


b.

Disconnect the H7 combination meter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O107,H7)Location & Routing

Click Connector(O107)Body>Floor Wire>Rear Combination Light Assembly LH

Click Connector(H7)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

O107-2 (B) - H7-5 (TRNL) Always Below 1 Ω
O107-1 (E) - Body ground Always Below 1 Ω
O107-2 (B) or H7-5 (TRNL) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

18.INSPECT REAR COMBINATION LIGHT ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.INSPECT REAR COMBINATION LIGHT ASSEMBLY LH

OK

REPLACE COMBINATION METER ASSEMBLY

NG

19.CHECK VEHICLE TYPE
a.

Check vehicle condition.

Result:
Result Proceed to
for Halogen Headlight A
for LED Headlight B




A

20.CHECK RH SIDE FRONT TURN SIGNAL LIGHT (FRONT TURN SIGNAL LIGHT SOCKET)

B

22.CHECK RH SIDE FRONT TURN SIGNAL LIGHT (DAYTIME RUNNING LIGHT ASSEMBLY RH)
20.CHECK RH SIDE FRONT TURN SIGNAL LIGHT (FRONT TURN SIGNAL LIGHT SOCKET)

Pre-procedure1

a.

Interchange the front turn signal light socket RH with LH and connect the connectors.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>FRONT TURN SIGNAL LIGHT BULB>REMOVAL



Procedure1

a.

Operate the turn signal switch and check that the RH side front turn signal light operates normally.

HINT:

If the RH side front turn signal light operates normally, the front turn signal light socket is malfunctioning.


Result:
Result Proceed to
RH side front turn signal light operates normally A
RH side front turn signal light does not blink B



Post-procedure1

a.

None



A

REPLACE FRONT TURN SIGNAL LIGHT SOCKET

B

21.CHECK HARNESS AND CONNECTOR (DAYTIME RUNNING LIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
21.CHECK HARNESS AND CONNECTOR (DAYTIME RUNNING LIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the B15 daytime running light assembly RH connector.


b.

Disconnect the H7 combination meter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B15,H7)Location & Routing

Click Connector(B15)Engine Compartment>No. 3 Engine Room Wire>Daytime Running Light Assembly RH

Click Connector(H7)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

B15-1 (B) - H7-2 (LR) Always Below 1 Ω
B15-2 (E) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.CHECK RH SIDE FRONT TURN SIGNAL LIGHT (DAYTIME RUNNING LIGHT ASSEMBLY RH)

Pre-procedure1

a.

Interchange the daytime running light assembly RH with LH and connect the connectors.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>DAYTIME RUNNING LIGHT ASSEMBLY>REMOVAL



Procedure1

a.

Operate the turn signal switch and check that the RH side front turn signal light operates normally.

HINT:

If the RH side front turn signal light operates normally, the daytime running light assembly RH is malfunctioning.



Post-procedure1

a.

None


Result:
Result Proceed to
RH side front turn signal light operates normally A
RH side front turn signal light does not blink B



A

REPLACE DAYTIME RUNNING LIGHT ASSEMBLY RH

B

23.CHECK HARNESS AND CONNECTOR (DAYTIME RUNNING LIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
23.CHECK HARNESS AND CONNECTOR (DAYTIME RUNNING LIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the B13 daytime running light assembly RH connector.


b.

Disconnect the H7 combination meter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B13,H7)Location & Routing

Click Connector(B13)Engine Compartment>No. 3 Engine Room Wire>Daytime Running Light Assembly RH

Click Connector(H7)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

B13-3 (B) - H7-2 (LR) Always Below 1 Ω
B13-1 (E) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.CHECK VEHICLE TYPE
a.

Check vehicle condition.

Result:
Result Proceed to
for Rear Turn Signal Light Bulb Type A
for Rear Turn Signal Light LED Type B




A

25.CHECK RH SIDE REAR TURN SIGNAL LIGHT (REAR TURN SIGNAL LIGHT SOCKET)

B

27.INSPECT LIGHTS
25.CHECK RH SIDE REAR TURN SIGNAL LIGHT (REAR TURN SIGNAL LIGHT SOCKET)

Pre-procedure1

a.

Interchange the rear turn signal light socket LH with RH and connect the connectors.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>REAR TURN SIGNAL LIGHT BULB>REMOVAL



Procedure1

a.

Operate the turn signal switch and check that the LH side rear turn signal light operates normally.

HINT:

If the LH side rear turn signal lights operates normally, the rear turn signal light socket is malfunctioning.


Result:
Result Proceed to
LH side rear turn signal lights operates normally A
LH side rear turn signal light does not blink B



Post-procedure1

a.

None



A

REPLACE REAR TURN SIGNAL LIGHT SOCKET

B

26.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
26.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the O103 rear combination light assembly RH connector.


b.

Disconnect the H7 combination meter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O103,H7)Location & Routing

Click Connector(O103)Body>Floor Wire>Rear Combination Light Assembly RH

Click Connector(H7)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

O103-1 (B) - H7-6 (TRNR) Always Below 1 Ω
O103-2 (E) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

27.INSPECT LIGHTS
a.

Inspect the illumination of each turn signal light.

Result:
Result Proceed to
All LH side rear turn signal lights do not blink. A
Rear light assembly RH does not illuminate B
Rear combination light assembly RH does not illuminate. C




A

28.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY RH AND REAR COMBINATION LIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)

B

32.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)

C

34.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
28.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY RH AND REAR COMBINATION LIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the Y14 rear light assembly RH connector.


b.

Disconnect the O110 rear combination light assembly RH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Rear light assembly RH
Tester Connection Condition Specified Condition

Click Location & Routing(Y14,H7)Location & Routing

Click Connector(Y14)Body>No. 2 Back Door Wire>Rear Light Assembly RH

Click Connector(H7)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

Y14-4 (TRN) - H7-6 (TRNR) Always Below 1 Ω
Y14-2 (E) - Body ground Always Below 1 Ω
Y14-4 (TRN) or H7-6 (TRNR) - Body ground Always Below 1 Ω

Rear combination light assembly RH
Tester Connection Condition Specified Condition

Click Location & Routing(O110,H7)Location & Routing

Click Connector(O110)Body>Floor Wire>Rear Combination Light Assembly RH

Click Connector(H7)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

O110-2 (B) - H7-6 (TRNR) Always Below 1 Ω
O110-1 (E) - Body ground Always Below 1 Ω
O110-2 (B) or H7-6 (TRNR) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

29.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY LH - REAR COMBINATION LIGHT ASSEMBLY LH AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

29.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY LH - REAR COMBINATION LIGHT ASSEMBLY LH AND BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Y14,O110)Location & Routing

Click Connector(Y14)Body>No. 2 Back Door Wire>Rear Light Assembly RH

Click Connector(O110)Body>Floor Wire>Rear Combination Light Assembly RH

Y14-1 (TRN4) - O110-4 (TRN4) Always Below 1 Ω
Y14-1 (TRN4) or O110-4 (TRN4) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

30.INSPECT REAR LIGHT ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

30.INSPECT REAR LIGHT ASSEMBLY RH

OK

31.INSPECT REAR COMBINATION LIGHT ASSEMBLY RH

NG

31.INSPECT REAR COMBINATION LIGHT ASSEMBLY RH

OK

REPLACE COMBINATION METER ASSEMBLY

NG

32.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the Y14 rear light assembly RH connector.


b.

Disconnect the H7 combination meter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Y14,H7)Location & Routing

Click Connector(Y14)Body>No. 2 Back Door Wire>Rear Light Assembly RH

Click Connector(H7)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

Y14-4 (TRN) - H7-6 (TRNR) Always Below 1 Ω
Y14-2 (E) - Body ground Always Below 1 Ω
Y14-4 (TRN) or H7-6 (TRNR) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

33.INSPECT REAR LIGHT ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

33.INSPECT REAR LIGHT ASSEMBLY RH

OK

REPLACE COMBINATION METER ASSEMBLY

NG

34.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the O110 rear combination light assembly RH connector.


b.

Disconnect the H7 combination meter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O110,H7)Location & Routing

Click Connector(O110)Body>Floor Wire>Rear Combination Light Assembly RH

Click Connector(H7)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

O110-2 (B) - H7-6 (TRNR) Always Below 1 Ω
O110-1 (E) - Body ground Always Below 1 Ω
O110-2 (B) or H7-6 (TRNR) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

35.INSPECT REAR COMBINATION LIGHT ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

35.INSPECT REAR COMBINATION LIGHT ASSEMBLY RH

OK

REPLACE COMBINATION METER ASSEMBLY

NG