Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM3700E _58 Vehicle Interior _093147 SUPPLEMENTAL RESTRAINT SYSTEMS _0438896 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B009E87  Right Side Restraints Sensor 5 Missing Message  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority Test Mode / Check Mode
B009E87 Right Side Restraints Sensor 5 Missing Message
·

The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 1) for 2 seconds

·

The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 1) for 2 seconds

·

The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 1) for 2 seconds

·

The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 1) for 2 seconds

·

Side airbag pressure sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Harness or connector

·

Side airbag pressure sensor RH

·

Airbag sensor assembly


Comes on SRS Airbag A Does not apply to test/check mode

WIRING DIAGRAM

B473434E97
4.781,2.917 6.5,3.333 1.719,0.417 10 false Airbag Sensor Assembly 4.781,2.74 5.417,2.917 0.635,0.177 10 false O24 4.823,1.01 5.938,1.438 1.115,0.427 10 false BBR+ 5.49,1.458 6.052,1.885 0.563,0.427 10 false Interface 4.552,1.01 4.75,1.25 0.198,0.24 10 false 25 4.823,1.688 5.938,2.115 1.115,0.427 10 false BBR- 4.552,1.688 4.75,2.083 0.198,0.396 10 false 26 2.604,1.01 3.719,1.438 1.115,0.427 10 false BDR+ 2.615,1.698 3.729,2.125 1.115,0.427 10 false BDR- 3.052,1.01 4.167,1.438 1.115,0.427 10 false 2 3.052,1.698 4.167,2.125 1.115,0.427 10 false 1 1.771,1.458 2.354,1.938 0.583,0.479 10 false Interface 0.771,1.458 1.354,1.854 0.583,0.396 10 false Element 0.552,2.344 1.25,2.542 0.698,0.198 10 false K1 0.552,2.521 3.354,2.906 2.802,0.385 10 false Side Airbag Pressure Sensor RH

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the cable to the auxiliary battery terminal, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Procedure1

a.

Check that the connectors are properly connected to the side airbag pressure sensor RH and airbag sensor assembly.

OK:

The connectors are properly connected.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS

Pre-procedure1

a.

Disconnect the connectors from the side airbag pressure sensor RH and airbag sensor assembly.


Procedure1

a.
C422860C02
1.521,0.438 1.521,0.802 false 2.635,1.083 2.938,1.521 0.302,0.438 10 false *2 0.385,0.771 0.667,0.979 0.281,0.208 10 false *1 1.448,0.25 1.75,0.417 0.302,0.167 10 false *3
*1 Side Airbag Pressure Sensor RH
*2 Airbag Sensor Assembly
*3 Wire Harness


Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals of the connectors are not deformed or damaged.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CHECK WIRE HARNESS (SHORT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK WIRE HARNESS (SHORT)
a.
C422854C08
0.896,2.292 1.24,2.521 0.344,0.229 1.49,2.833 1.802,2.448 true 2.344,2.833 1.979,2.448 true 1.646,0.552 1.646,0.302 false 0.563,0.552 0.802,0.833 0.24,0.281 10 false *1 2.698,0.854 3.01,1.188 0.313,0.333 10 false *2 1.583,0.125 1.844,0.292 0.26,0.167 10 false *3 0.708,1.833 1,2.083 0.292,0.25 10 false *a 2.24,0.552 2.385,0.75 0.146,0.198 10 false A 1.885,0.552 2.083,0.833 0.198,0.281 10 false B 1.292,0.552 1.5,0.75 0.208,0.198 10 false C 0.938,0.552 1.125,0.75 0.188,0.198 10 false D 0.979,2.333 1.25,2.51 0.271,0.177 10 false K1 2.229,2.865 2.75,3.083 0.521,0.219 10 false BDR+ 1.281,2.865 1.75,3.083 0.469,0.219 10 false BDR-
*1 Side Airbag Pressure Sensor RH
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Side Airbag Pressure Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(K1)Location & Routing

Click Connector(K1)Body>Front Door Wire RH / Television Camera Wire>Side Airbag Pressure Sensor RH

K1-2 (BDR+) - K1-1 (BDR-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK WIRE HARNESS (SHORT TO GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WIRE HARNESS (SHORT TO GROUND)
a.
C422854C08
0.896,2.292 1.24,2.521 0.344,0.229 1.49,2.833 1.802,2.448 true 2.344,2.833 1.979,2.448 true 1.646,0.552 1.646,0.302 false 0.563,0.552 0.802,0.833 0.24,0.281 10 false *1 2.698,0.854 3.01,1.188 0.313,0.333 10 false *2 1.583,0.125 1.844,0.292 0.26,0.167 10 false *3 0.708,1.833 1,2.083 0.292,0.25 10 false *a 2.24,0.552 2.385,0.75 0.146,0.198 10 false A 1.885,0.552 2.083,0.833 0.198,0.281 10 false B 1.292,0.552 1.5,0.75 0.208,0.198 10 false C 0.938,0.552 1.125,0.75 0.188,0.198 10 false D 0.979,2.333 1.25,2.51 0.271,0.177 10 false K1 2.229,2.865 2.75,3.083 0.521,0.219 10 false BDR+ 1.281,2.865 1.75,3.083 0.469,0.219 10 false BDR-
*1 Side Airbag Pressure Sensor RH
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Side Airbag Pressure Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(K1)Location & Routing

Click Connector(K1)Body>Front Door Wire RH / Television Camera Wire>Side Airbag Pressure Sensor RH

K1-2 (BDR+) - Body ground Always 1 MΩ or higher
K1-1 (BDR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK WIRE HARNESS (OPEN)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK WIRE HARNESS (OPEN)

Pre-procedure1

a.
C422893C01
0.823,0.833 1.167,1.063 0.344,0.229 0.958,3.729 1.302,3.958 0.344,0.229 1.573,1.823 1.573,1.688 false 1.167,1.729 1.51,1.302 true 2.073,1.729 1.656,1.292 true 1.667,2.854 1.667,2.521 false 1.5,4.271 1.802,3.844 true 2.333,4.271 1.99,3.844 true 0.625,2.375 0.854,2.646 0.229,0.271 10 false *1 2.51,2.656 2.833,2.833 0.323,0.177 10 false *2 1.615,2.896 1.948,3.146 0.333,0.25 10 false *3 1.51,1.844 1.938,2.24 0.427,0.396 10 false *4 0.677,0.188 1.177,0.688 0.5,0.5 10 false *b 0.708,3.427 1.156,3.813 0.448,0.385 10 false *a 2.188,2.375 2.333,2.583 0.146,0.208 10 false A 1.885,2.375 2,2.583 0.115,0.208 10 false B 1.292,2.375 1.5,2.583 0.208,0.208 10 false C 0.979,2.375 1.167,2.583 0.188,0.208 10 false D 1.031,3.76 1.479,4.146 0.448,0.385 10 false K1 0.875,0.875 1.323,1.26 0.448,0.385 10 false O24 2.156,1.667 2.594,1.938 0.438,0.271 10 false BBR- 0.896,1.76 1.344,2.146 0.448,0.385 10 false BBR+ 2.219,4.281 2.677,4.573 0.458,0.292 10 false BDR+ 1.365,4.281 1.865,4.583 0.5,0.302 10 false BDR-
*1 Side Airbag Pressure Sensor RH
*2 Airbag Sensor Assembly
*3 Wire Harness
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Pressure Sensor RH)
*b Front view of wire harness connector
(to Airbag Sensor Assembly RH)


Using a service wire, connect terminals 2 (BDR+) and 1 (BDR-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(K1)Location & Routing

Click Connector(K1)Body>Front Door Wire RH / Television Camera Wire>Side Airbag Pressure Sensor RH

K1-2 (BDR+) - K1-1 (BDR-) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Disconnect the service wire from connector C.



OK

6.CHECK WIRE HARNESS (SHORT TO B+)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK WIRE HARNESS (SHORT TO B+)

Pre-procedure1

a.

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the ignition switch to ON.


Procedure1

a.
C422854C08
0.896,2.292 1.24,2.521 0.344,0.229 1.49,2.833 1.802,2.448 true 2.344,2.833 1.979,2.448 true 1.646,0.552 1.646,0.302 false 0.563,0.552 0.802,0.833 0.24,0.281 10 false *1 2.698,0.854 3.01,1.188 0.313,0.333 10 false *2 1.583,0.125 1.844,0.292 0.26,0.167 10 false *3 0.708,1.833 1,2.083 0.292,0.25 10 false *a 2.24,0.552 2.385,0.75 0.146,0.198 10 false A 1.885,0.552 2.083,0.833 0.198,0.281 10 false B 1.292,0.552 1.5,0.75 0.208,0.198 10 false C 0.938,0.552 1.125,0.75 0.188,0.198 10 false D 0.979,2.333 1.25,2.51 0.271,0.177 10 false K1 2.229,2.865 2.75,3.083 0.521,0.219 10 false BDR+ 1.281,2.865 1.75,3.083 0.469,0.219 10 false BDR-
*1 Side Airbag Pressure Sensor RH
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Side Airbag Pressure Sensor RH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(K1)Location & Routing

Click Connector(K1)Body>Front Door Wire RH / Television Camera Wire>Side Airbag Pressure Sensor RH

K1-2 (BDR+) - Body ground Ignition switch ON Below 1 V
K1-1 (BDR-) - Body ground Ignition switch ON Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




OK

7.CHECK SIDE AIRBAG PRESSURE SENSOR RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK SIDE AIRBAG PRESSURE SENSOR RH
a.

Connect the connector to the airbag sensor assembly.


b.
C422835C01
0.719,0.813 1.073,1.24 0.354,0.427 10 false *1 1.104,0.813 1.354,1.25 0.25,0.438 10 false D 1.26,0.813 1.573,1.167 0.313,0.354 10 false C 1.729,0.813 2.031,1.073 0.302,0.26 10 false B 1.885,0.813 2.135,1.073 0.25,0.26 10 false A 2.323,1.135 2.688,1.427 0.365,0.292 10 false *2
*1 Side Airbag Pressure Sensor LH
*2 Airbag Sensor Assembly


Interchange the side airbag pressure sensor RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

f.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

8.CHECK SIDE AIRBAG PRESSURE SENSOR RH
8.CHECK SIDE AIRBAG PRESSURE SENSOR RH

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
HINT:

Codes other than DTCs B009B87 and B009E87 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
B009E87 is output A
B009B87 is output B
B009B87 and B009E87 are not output C


Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Return the side airbag pressure sensor RH and LH to their original positions and connect the connectors.



A

B

C