Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR › 2020.08–2021.07
RM3700E _55 Steering _093192 STEERING GEAR / LINKAGE _0439085 STEERING GEAR A

STEERING GEAR / LINKAGE  STEERING GEAR  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B586152N01
6.521,0.208 6.865,0.208 false 3.792,0.188 4.135,0.188 false 2.635,0.813 2.635,0.49 false 3.792,0.896 4.281,0.542 4.281,0.542 4.479,0.542 false 4.479,0.875 4.823,0.875 false 5.104,1.854 5.438,1.646 5.438,1.646 5.635,1.646 false 2.646,2.573 2.646,2.25 false 4.885,0.802 5.042,1 0.156,0.198 10 false ● 4.49,0.917 4.677,1.125 0.188,0.208 10 false x2 4.531,3.604 4.74,3.771 0.208,0.167 10 false x2 6.094,0.083 6.552,0.396 0.458,0.313 18 false 1, 2 4.208,0.021 4.667,0.333 0.458,0.313 18 false 5 4.844,0.427 5.302,0.74 0.458,0.313 18 false 4, 6 2.583,0.813 3.042,1.125 0.458,0.313 18 false 8 2.594,2.583 3.052,2.896 0.458,0.313 18 false 3 5.938,1.521 6.396,1.833 0.458,0.313 18 false 7

Procedure Part Name Code
Z101186

Z101188

Z101187

1 ALIGN FRONT WHEELS FACING STRAIGHT AHEAD - (Click here) - -
2 SECURE STEERING WHEEL - (Click here) - -
3 FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY 51201 - - -
4 REMOVE STEERING LINK ASSEMBLY - (Click here) - -
5 STEERING COLUMN HOLE COVER 45253 - - -
6 SECURE STEERING LINK ASSEMBLY - (Click here) - -
7 TIE ROD END SUB-ASSEMBLY LH 45047 (Click here) - -
8 TIE ROD END SUB-ASSEMBLY RH 45046 (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the steering link assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Wheel alignment adjustment for HV Model:
1.

Perform "Reset Memory"

2.

Perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
for Gasoline Model:
Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (Click here)

PROCEDURE

Hide 1. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

a.
B585933N02
1.104,0.063 1.385,0.417 0.281,0.354 18 false i

i.

Align the front wheels facing straight ahead.



Hide 2. SECURE STEERING WHEEL

a.
B586153N01
0.406,0.042 0.615,0.313 0.208,0.271 18 true i

i.

Secure the steering wheel with the seat belt to prevent damage to the spiral cable by rotation of the steering wheel.



Hide 51201 3.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 4.REMOVE STEERING LINK ASSEMBLY

a.
B586154C01
0.417,0.083 0.698,0.438 0.281,0.354 18 false i
V100136

Front of the Vehicle - -


i.

Remove the 2 bolts, 2 nuts and steering link assembly from the front suspension crossmember sub-assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.




Hide 45253 5.REMOVE STEERING COLUMN HOLE COVER

a.
B586155


Hide 6.SECURE STEERING LINK ASSEMBLY

a.
B586156N01
3.229,0.406 3.573,0.729 true 2.969,0.292 3.281,0.49 0.313,0.198 10 false SST 1.708,0.052 2.083,0.333 0.375,0.281 18 true i

i.

Using SST with wrapped in protective tape, secure the steering link assembly in a vise.

SST
09612-00012  



Hide 45047 7.REMOVE TIE ROD END SUB-ASSEMBLY LH

a.
B586157C01
1.938,1.271 1.938,0.906 true 2.219,1.26 1.802,1.26 1.802,1.26 1.802,0.896 true 0.417,0.063 0.698,0.417 0.281,0.354 18 false i 3.833,0.094 4.115,0.448 0.281,0.354 18 false ii 2.271,1.167 2.583,1.365 0.313,0.198 10 false *a
*a Matchmark - -


i.

Put matchmarks on the tie rod end sub-assembly LH and steering gear assembly.


ii.

Remove the tie rod end sub-assembly LH and lock nut.



Hide 45046 8.REMOVE TIE ROD END SUB-ASSEMBLY RH

a.

Perform the same procedure as for the LH side.