| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 10 | FRONT FENDER LINER LH | 53876A | - | - | - |
| 11 | FRONT FENDER LINER RH | 53875A | - | - | - |
| *A | for AWD | - | - |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 20 | ENGINE MOVING CONTROL ROD | 12363A | ( )
|
- | - |
| 21 | FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY | 51201 | ( )
|
- | - |
| ● | Non-reusable part | - | - |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front suspension crossmember sub-assembly removal/installation are shown below.
45259A
3.REMOVE COLUMN HOLE COVER SILENCER SHEET
45260
4.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
5.REMOVE FRONT WHEELS
51410
6.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY
51442C
7.REMOVE ENGINE UNDER COVER LH
51441C
8.REMOVE ENGINE UNDER COVER RH
Perform the same procedure as for the LH side.
51447D
9.REMOVE CENTER NO. 4 ENGINE UNDER COVER
53876A
10.SEPARATE FRONT FENDER LINER LH
53875A
11.SEPARATE FRONT FENDER LINER RH
Perform the same procedure as for the LH side.
48810
12.SEPARATE FRONT STABILIZER LINK ASSEMBLY LH
|
|
Remove the nut and separate the front stabilizer link assembly LH from the front stabilizer bar.
Do not damage the boot of the ball joint.
48820B
13.SEPARATE FRONT STABILIZER LINK ASSEMBLY RH
Perform the same procedure as for the LH side.
45047
14.SEPARATE TIE ROD END SUB-ASSEMBLY LH
| *a | String | *b | Center Nut |
| *c | Place wrench here | *d | Molybdenum Grease Application Area |
|
Turn | - | - |
Remove the cotter pin and nut.
Install SST to the tie rod end sub-assembly LH.
Make sure that the lower ends of the tie rod end sub-assembly LH and SST are aligned.
Secure SST using a string.
Be sure to tighten the string firmly to secure SST to the steering knuckle LH to prevent SST from falling off.
Using SST, separate the tie rod end sub-assembly LH from the steering knuckle LH.
Apply molybdenum grease to the bolt threads and the tip of SST.
Be sure to tighten the string firmly to secure SST to the steering knuckle LH to prevent SST from falling off.
Install SST with the center nut so that (A) and (B) shown in the illustration are parallel. Otherwise, the ball joint dust cover may be damaged.
Be sure to place the wrench on the part shown in the illustration.
Do not damage the front disc brake dust cover.
Do not damage the ball joint dust cover.
Do not damage the steering knuckle LH.
45046
15.SEPARATE TIE ROD END SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
48069
16.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
48068
17.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
82715W
18.REMOVE WIRING HARNESS CLAMP BRACKET
8946A
19.REMOVE EXHAUST SENSOR CLAMP BRACKET (for AWD)
12363A
20.REMOVE ENGINE MOVING CONTROL ROD
| *a | Transmission Jack | *b | Wooden Block |
|
Front of the Vehicle |
|
Wooden block placement location |
Using a transmission jack and a wooden block, support the engine assembly with transaxle.
Support the engine assembly with transaxle until the front suspension crossmember sub-assembly is installed.
If the support is removed before the front suspension crossmember sub-assembly is installed, the engine assembly with transaxle may drop.
Remove the bolt and separate the engine moving control rod.
51201
21.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
| *a | Engine Lifter | *b | Attachment |
|
Attachment placement location | - | - |
Support the front suspension crossmember sub-assembly with an engine lifter using 4 attachments or equivalent tools as shown in the illustration.
The front suspension crossmember sub-assembly is a very heavy component. Make sure that it is supported securely.
If the front suspension crossmember sub-assembly is not securely supported, it may drop, resulting in serious injury.
Use attachments to keep the front suspension crossmember sub-assembly level.
Remove the 10 bolts and front suspension crossmember sub-assembly.
Slowly lower the front suspension crossmember sub-assembly.
When lowering the front suspension crossmember sub-assembly, be careful not to damage the vehicle body or other components installed to the vehicle.
Make sure that the front suspension crossmember sub-assembly not hit the protrusion of the reinforcement.
12363A
22.REMOVE ENGINE MOVING CONTROL ROD
48069
23.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
Remove the 2 bolts, nut and front lower No. 1 suspension arm sub-assembly LH from the front suspension crossmember sub-assembly.
Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.
48068
24.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
48811
26.REMOVE FRONT STABILIZER BAR