Home › Engine / Hybrid System › M15A-FXE (EMISSION CONTROL) › EGR COOLER › 2020.08–2021.07
RM3700E _51 Engine / Hybrid System _093307 M15A-FXE EMISSION CONTROL _0440394 EGR COOLER A

M15A-FXE EMISSION CONTROL  EGR COOLER  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A459916N01
1.615,0.76 5.885,2.906 4.271,2.146 3.75,1.25 4,1 4,1 4.167,1 false 0.781,0.75 1.115,0.75 false 2,1.75 2,2.083 false 3.479,3.25 3.813,3.25 false 4.604,2 4.938,2 false 5.885,2.417 6.219,2.417 false 1.927,2.125 2.24,2.323 0.313,0.198 10 false *1 0.406,0.708 0.719,0.906 0.313,0.198 10 false ● 4.219,0.948 4.531,1.146 0.313,0.198 10 false ● 6.458,1.719 6.771,1.917 0.313,0.198 10 false x2 6.281,2.271 6.563,2.625 0.281,0.354 18 false 1 0.604,0.625 0.885,0.979 0.281,0.354 18 false 2 4.385,0.875 4.667,1.229 0.281,0.354 18 false 5 3.281,3.125 3.563,3.479 0.281,0.354 18 false 4 4.406,1.865 4.688,2.219 0.281,0.354 18 false 3 3.052,3.208 3.365,3.406 0.313,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 EGR VALVE WITH EGR COOLER ASSEMBLY - - - -
2 EGR PIPE GASKET 25634 - - -
3 EGR COOLER ASSEMBLY 25680 - - -
4 NO. 1 EGR COOLER GASKET 25685 - - -
5 EGR VALVE GASKET 25627 - - -

*1 EGR VALVE ASSEMBLY - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during EGR cooler assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Gas leaks from exhaust system is repaired Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1.REMOVE EGR VALVE WITH EGR COOLER ASSEMBLY

Hide 25680 3.REMOVE EGR COOLER ASSEMBLY

a.
A458665


Hide 25685 4.REMOVE NO. 1 EGR COOLER GASKET

a.
A458666