Home › Engine / Hybrid System › M15A-FXE (EMISSION CONTROL) › EGR VALVE › 2020.08–2021.07
RM3700E _51 Engine / Hybrid System _093307 M15A-FXE EMISSION CONTROL _0440393 EGR VALVE A

M15A-FXE EMISSION CONTROL  EGR VALVE  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A472056N02
1.01,0.927 1.344,0.927 false 2.719,3.729 3.052,3.729 false 6.51,0.25 6.844,0.25 false 4.083,4.635 4.271,4.813 0.188,0.177 10 false x4 4.531,4.604 4.719,4.781 0.188,0.177 10 false x5 4.813,4.531 5,4.708 0.188,0.177 10 false x9 2.542,3.594 2.823,3.948 0.281,0.354 18 false 1 0.854,0.802 1.135,1.156 0.281,0.354 18 false 3 6.281,0.115 6.479,0.448 0.198,0.333 18 true 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 NO. 1 ENGINE UNDER COVER ASSEMBLY 51410 - - -
2 ENGINE COOLANT - - (Click here) -
3 HYBRID MOTOR CONTROL INVERTER ASSEMBLY G92A0 - - -

A477269N02
2,0.583 2.333,0.583 false 1.167,2.5 1.5,2.5 false 2.625,3 2.625,3.333 false 4.031,1.333 4.365,1.333 false 5.875,1.25 6.208,1.25 false 4.885,3.083 5.219,3.083 false 3.792,0.396 4.104,0.594 0.313,0.198 10 false *a 5.073,1.948 5.385,2.146 0.313,0.198 10 false *b 2.417,3.417 2.729,3.615 0.313,0.198 10 false ● 1.615,0.531 1.927,0.729 0.313,0.198 10 false ● 1.802,0.458 2.083,0.813 0.281,0.354 18 false 9 0.979,2.375 1.26,2.729 0.281,0.354 18 false 4 2.583,3.344 2.865,3.698 0.281,0.354 18 false 8 5.281,2.938 5.563,3.292 0.281,0.354 18 false 5 6.292,1.104 6.573,1.458 0.281,0.354 18 false 6 4.448,1.177 4.729,1.531 0.281,0.354 18 false 7

Procedure Part Name Code
Z101186

Z101188

Z101187

4 NO. 5 WATER BY-PASS HOSE 16282 - - -
5 NO. 3 WATER BY-PASS HOSE ASSEMBLY 16290F - - -
6 NO. 4 WATER BY-PASS HOSE 16281N - - -
7 EGR VALVE WITH EGR COOLER ASSEMBLY - - - -
8 NO. 1 EGR COOLER GASKET 25685 - - -
9 EGR PIPE GASKET 25634 - - -

*a x1 or x2 *b x4 or x3
● Non-reusable part - -

A459920N04
3.615,1.26 3.615,1.594 false 1.354,1.167 1.354,1.5 false 5.417,1.833 5.75,1.833 false 5.885,1.229 6.198,1.427 0.313,0.198 10 false x2 5.813,1.76 6.125,1.958 0.313,0.198 10 false *1 3.333,1.719 3.615,1.958 0.281,0.24 10 false ● 3.5,1.646 4.052,2 0.552,0.354 18 false 11 1.208,1.552 1.76,1.906 0.552,0.354 18 false 10

Procedure Part Name Code
Z101186

Z101188

Z101187

10 EGR VALVE ASSEMBLY 25620 - - -
11 EGR VALVE GASKET 25627 - - -

*1 EGR COOLER ASSEMBLY - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during EGR valve assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
·

Replacement of EGR valve assembly

·

Gas leaks from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 51410 1.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide G92A0 3.REMOVE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

Hide 16282 4.DISCONNECT NO. 5 WATER BY-PASS HOSE

a.
A458669


Hide 16290F 5.DISCONNECT NO. 3 WATER BY-PASS HOSE ASSEMBLY

a.
A458670


Hide 16281N 6.DISCONNECT NO. 4 WATER BY-PASS HOSE

a.
A458671


Hide 7.REMOVE EGR VALVE WITH EGR COOLER ASSEMBLY

a.
A458713

The illustrations are representative examples, and details may differ.



Hide 25685 8.REMOVE NO. 1 EGR COOLER GASKET

Hide 25634 9.REMOVE EGR PIPE GASKET

a.
A458668


Hide 25620 10.REMOVE EGR VALVE ASSEMBLY

a.
A458664


Hide 25627 11.REMOVE EGR VALVE GASKET

a.
A458667