Home › Engine / Hybrid System › M15A-FKS (FUEL) › FUEL INJECTOR › 2020.08–2021.07
RM3700E _51 Engine / Hybrid System _093308 M15A-FKS FUEL _0440419 FUEL INJECTOR A

M15A-FKS FUEL  FUEL INJECTOR  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A459878N03
3.208,3.51 2.875,4.333 2.875,4.333 2.708,4.333 false 3.063,3.469 2.75,3.969 2.75,3.969 2.583,3.969 false 2.865,3.417 2.74,3.604 2.74,3.604 2.573,3.604 false 2.563,3.208 2.729,2.844 2.729,2.844 2.896,2.844 false 2.469,2.5 2.635,2.135 2.635,2.135 2.802,2.135 false 2.198,3.156 2,3.833 2,3.833 1.833,3.833 false 1.958,3.042 1.667,3.448 1.667,3.448 1.5,3.448 false 1.073,2.823 0.885,3.094 0.885,3.094 0.719,3.094 false 1.375,2.24 1.708,2.24 false 5.177,1.552 5.344,1.938 5.344,1.938 5.51,1.938 false 6.813,0.25 6.479,0.25 false 1.573,1.115 1.906,1.115 false 0.833,4.052 1.167,4.052 false 6.771,0.771 6.438,0.771 false 2.052,3.104 1.885,3.583 1.885,3.583 1.719,3.583 false 0.479,2.229 0.792,2.427 0.313,0.198 10 false x3 1.969,2.875 2.281,3.073 0.313,0.198 10 false x3 2.125,2.958 2.438,3.156 0.313,0.198 10 false x3 2.271,3.01 2.583,3.208 0.313,0.198 10 false x3 2.552,2.615 2.865,2.813 0.313,0.198 10 false x3 2.594,3.333 2.906,3.531 0.313,0.198 10 false x3 2.969,3.24 3.281,3.438 0.313,0.198 10 false x3 3.135,3.313 3.448,3.51 0.313,0.198 10 false x3 3.271,3.396 3.583,3.594 0.313,0.198 10 false x3 2.25,4.302 2.563,4.5 0.313,0.198 10 false ● 6.01,0.115 6.49,0.396 0.479,0.281 18 false 1, 2 1.385,0.99 1.667,1.344 0.281,0.354 18 false 4 5.896,1.813 6.177,2.167 0.281,0.354 18 false 5 0.656,3.927 0.938,4.281 0.281,0.354 18 false 6 1.771,2.094 2.052,2.448 0.281,0.354 18 false 7 0.521,2.969 0.802,3.323 0.281,0.354 18 false 8 3.271,2.719 3.552,3.073 0.281,0.354 18 false 9 2.885,2 3.26,2.302 0.375,0.302 18 false 10 1.167,3.313 1.521,3.604 0.354,0.292 18 false 11 1.563,3.698 1.917,4.01 0.354,0.313 18 false 12 2.25,3.823 2.573,4.146 0.323,0.323 18 false 13 2.271,3.479 2.646,3.75 0.375,0.271 18 false 14 2.406,4.219 2.729,4.521 0.323,0.302 18 false 15 2.073,3.906 2.396,4.104 0.323,0.198 10 false ● 2.115,3.563 2.438,3.76 0.323,0.198 10 false ● 1.438,3.781 1.76,3.979 0.323,0.198 10 false ● 0.99,3.385 1.313,3.583 0.323,0.198 10 false ● 6.229,0.625 6.51,0.979 0.281,0.354 18 false 3 1.51,3.531 1.833,3.729 0.323,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 DISCHARGE FUEL SYSTEM PRESSURE - (Click here) - -
2 PRECAUTION - (Click here) - -
3 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
4 INTAKE MANIFOLD 17111 - - -
5 NO. 1 FUEL PIPE SUB-ASSEMBLY 23801P (Click here) - -
6 ENGINE WIRE - - - -
7 FUEL DELIVERY INSULATOR 23845G - - -
8 FUEL DELIVERY PIPE 23814B (Click here) - -
9 FUEL INJECTOR ASSEMBLY 23250 (Click here) - -
10 NOZZLE HOLDER CLAMP 23695A - - -
11 NO. 3 FUEL INJECTOR BACK-UP RING 23258 (Click here) - -
12 NO. 1 FUEL INJECTOR BACK-UP RING 23256 - - -
13 C-RING - - - -
14 INJECTOR VIBRATION INSULATOR 23291A - - -
15 FUEL INJECTOR SEAL 23255A (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel injector assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Replacement of fuel injector assembly Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



NOTICE:
·

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. DISCHARGE FUEL SYSTEM PRESSURE

Hide 2. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 23801P 5.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide 6.SEPARATE ENGINE WIRE

a.
A459799


Hide 23845G 7.REMOVE FUEL DELIVERY INSULATOR

a.
A459648


Hide 23814B 8.REMOVE FUEL DELIVERY PIPE

a.
Z101186

NOTICE:
·

Make sure not to touch or strike the tips of the fuel injector assemblies.

·

Pull and remove the fuel delivery pipe in a straight line without tilting it.

·

When replacing the fuel delivery pipe, it is necessary to replace the No. 1 fuel pipe sub-assembly with a new one.




A459649


Hide 23250 9.REMOVE FUEL INJECTOR ASSEMBLY

a.
A474484N02
0.448,0.063 0.729,0.417 0.281,0.354 18 false i

i.

Secure the fuel delivery pipe in a vise between aluminum plates and pull out the 3 fuel injector assemblies.

NOTICE:
·

Pull and remove each fuel injector assembly in a straight line to avoid damaging the seal surface of the fuel delivery pipe O-ring.

·

After removing the fuel injector assemblies, remove any O-rings, No. 1 fuel injector back-up rings and No. 3 fuel injector back-up rings remaining on the fuel delivery pipe side.

·

Attach a tag or label with the corresponding cylinder number to each fuel injector assembly so that they can be installed to their original locations.

·

Cover the tip of each fuel injector assembly to prevent it from being damaged.





Hide 23695A 10.REMOVE NOZZLE HOLDER CLAMP

a.
A458891


Hide 23258 11.REMOVE NO. 3 FUEL INJECTOR BACK-UP RING

Z101186

NOTICE:

Do not damage the area that contacts the O-ring.



a.
A458892


Hide 23256 12.REMOVE NO. 1 FUEL INJECTOR BACK-UP RING

a.
A458893


Hide 13.REMOVE C-RING

a.
A458894


Hide 23291A 14.REMOVE INJECTOR VIBRATION INSULATOR

a.
A458895


Hide 23255A 15.REMOVE FUEL INJECTOR SEAL

a.
A459650N01
5.406,0.135 5.688,0.49 0.281,0.354 18 false i 2.146,0.104 2.427,0.458 0.281,0.354 18 false ii

i.

Using the tip of needle nose pliers, pinch and pull the fuel injector seal at several points to stretch it.

NOTICE:
·

Excessively pinching the fuel injector seal may damage the groove of the fuel injector assembly.

·

If a fuel injector assembly is dropped or the tip of the fuel injector assembly is struck, replace it with a new one.




ii.

Remove the fuel injector seal from each fuel injector assembly.