|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| * | For use with a union nut wrench | ● | Non-reusable part |
This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
23470
1.INSTALL FUEL PUMP LIFTER ASSEMBLY
|
|
| *1 | Fuel Pump Assembly | *2 | Fuel Pump Lifter Assembly |
| *3 | No. 2 Camshaft | *4 | Cylinder Head Cover Sub-assembly |
| *5 | Fuel Pump Spacer Gasket | - | - |
| *a | Correct | *b | Incorrect |
| *c | Pump Drive Cam (Engine Oil Application Area) | *d | Fuel Pump Lifter Assembly (Engine Oil Application Area) |
| *e | Fuel Pump Lifter Assembly (Engine Oil Application Area) | *f | Fuel Pump Lifter Guide (Engine Oil Application Area) |
| *g | Stopper Key | *h | Key Groove |
Turn the crankshaft pulley until the flat of the No. 2 camshaft faces the fuel pump lifter assembly.
This prevents the No. 2 camshaft nose from pushing up the fuel pump lifter assembly when installing the fuel pump assembly.
Apply 30 cc (1.8 cu. in.) of engine oil to the pump drive cam.
Apply engine oil to the fuel pump lifter assembly.
Install a new fuel pump spacer gasket to the cylinder head cover sub-assembly.
Apply engine oil to the inside of the fuel pump lifter guide and the outside of the fuel pump lifter assembly.
Set the fuel pump lifter assembly on the fuel pump lifter guide as shown in the illustration.
Align the stopper key of the fuel pump lifter assembly with the key groove of the fuel pump lifter guide.
23191
2.INSTALL FUEL PUMP FLANGE
3.TEMPORARILY INSTALL FUEL PUMP ASSEMBLY
Apply engine oil to a new O-ring and install it to the fuel pump assembly.
Do not damage the O-ring.
Set the fuel pump flange and fuel pump assembly on the cylinder head cover sub-assembly as shown in the illustration.
Temporarily install the fuel pump assembly with the 2 bolts, leaving some allowance for left and right movement.
23801P
4.TEMPORARILY INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY
|
|
Temporarily install the bolt.
Temporarily install the No. 1 fuel pipe sub-assembly to the fuel delivery pipe and tighten the union nut by hand.
Temporarily install the No. 1 fuel pipe sub-assembly to the fuel pump assembly and tighten the union nut by hand.
5.INSTALL FUEL PUMP ASSEMBLY
Tighten the 2 bolts.
Connect the fuel pump assembly connector.
23801P
6.INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY
| *a | 17 mm Union Nut Wrench | *b | Torque Wrench Fulcrum Length |
Using a 17 mm union nut wrench, tighten the union nut on the fuel delivery pipe side of the No. 1 fuel pipe sub-assembly.
Do not adjust the torque in the loosening direction.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)
Using a 17 mm union nut wrench, tighten the union nut on the fuel pump assembly side of the No. 1 fuel pipe sub-assembly.
Do not adjust the torque in the loosening direction.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)
Using an 8 mm socket wrench, tighten the bolt.
Connect the ignition coil assembly connector.
23902
7.CONNECT FUEL TUBE SUB-ASSEMBLY
Connect the fuel tube sub-assembly to the fuel pump assembly.
Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION
44771
8.INSTALL VACUUM TUBE CONNECTOR HOSE
17881
9.INSTALL NO. 1 AIR CLEANER HOSE
12262
10.CONNECT NO. 2 VENTILATION HOSE
11.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
12.INSPECT FOR FUEL LEAK
13. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
14.PERFORM INITIALIZATION
Perform "Inspection After Repair" after replacing the fuel pump assembly.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION