Home › Engine / Hybrid System › M15A-FXE (FUEL) › FUEL PUMP › 2020.08–2021.07
RM3700E _51 Engine / Hybrid System _093309 M15A-FXE FUEL _0440432 FUEL PUMP A

M15A-FXE FUEL  FUEL PUMP  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
A462019N03
2.927,2.031 3.26,2.031 false 4.01,2.573 4.344,2.573 false 3.969,2.969 4.302,2.969 false 6.365,0.271 6.698,0.271 false 6.469,0.75 6.802,0.75 false 6.417,1.292 6.75,1.292 false 5.052,3.563 5.385,3.563 false 3.865,3.76 4.198,3.76 false 3.073,4.688 3.406,4.688 false 2.542,2.635 2.708,2.635 2.708,2.635 2.854,2.833 false 1.667,1.833 1.833,1.833 1.833,1.833 2.042,2.302 false 1.073,0.677 1.406,0.677 false 4.427,2.49 4.583,2.688 0.156,0.198 10 false ● 2.885,4.625 3.125,4.813 0.24,0.188 10 false ● 4.604,3.646 4.885,4 0.281,0.354 18 false 1 5.438,3.427 5.719,3.781 0.281,0.354 18 false 4 4.688,2.844 4.969,3.198 0.281,0.354 18 false 2 2.74,1.885 3.021,2.24 0.281,0.354 18 false 6 6.271,0.604 6.552,0.958 0.281,0.354 18 false 8 6.208,1.156 6.49,1.51 0.281,0.354 18 false 7 5.667,0.135 6.479,0.479 0.813,0.344 18 false 10, 11 2.323,2.5 2.604,2.854 0.281,0.354 18 false 5 1.479,1.719 1.76,2.073 0.281,0.354 18 false 3 0.865,0.531 1.146,0.885 0.281,0.354 18 false 9

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY 77020A (Click here) - -
2 FUEL PUMP GAUGE RETAINER 77144 (Click here) - -
3 FUEL TANK MAIN TUBE SUB-ASSEMBLY 77209F (Click here) - -
4 NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY 77701W - - -
5 NO. 1 FUEL EMISSION TUBE SUB-ASSEMBLY 77027B - - -
6 REAR FLOOR SERVICE HOLE COVER 58325E (Click here) - -
7 CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
8 INSPECT FOR FUEL LEAK - (Click here) - -
9 REAR SEAT ASSEMBLY - - - -
10 INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL - - - (Click here)
11 PERFORM INITIALIZATION - - - (Click here)

● Non-reusable part - -

PROCEDURE

Hide 77020A 1.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

a.
A456992C02
1.521,3.375 1.323,3.521 true 4.177,3.24 4.344,3.969 4.344,3.969 3.146,3.719 true 4.385,3.896 4.583,4.073 0.198,0.177 10 true *a 1.135,3.448 1.313,3.625 0.177,0.177 10 true *b 0.135,0.073 0.417,0.427 0.281,0.354 18 false i 3.958,0.094 4.156,0.385 0.198,0.292 18 true ii 0.552,2.604 0.833,2.958 0.281,0.354 18 false iii
*1 Protrusion *2 Notch


i.

Install a new fuel suction tube set gasket to the fuel tank assembly.


ii.

Set the fuel suction tube with pump and gauge assembly to the fuel tank assembly.

NOTICE:
·

Be careful not to bend the arm of the fuel sender gauge assembly.

·

To avoid applying excessive force to the tip of the fuel sender gauge assembly, tilt the fuel sub-tank sub-assembly diagonally and insert it into the fuel tank assembly as shown in the illustration.


A461402C01
1.823,0.469 2.104,0.469 false 1.906,1.167 2.115,1.167 false 1.844,1.563 2.125,1.563 false 5.344,1.646 5.521,1.531 false 5.125,1.333 5.573,0.865 true 5.042,0.844 5.396,0.573 false 2.167,1.49 2.479,1.646 0.313,0.156 10 false *1 2.156,1.104 2.469,1.26 0.313,0.156 10 false *2 2.135,0.406 2.448,0.563 0.313,0.156 10 false *3 5.552,1.438 5.865,1.594 0.313,0.156 10 false *1 5.635,0.781 5.948,0.938 0.313,0.156 10 false *2 5.438,0.49 5.75,0.646 0.313,0.156 10 false *3
*1 Fuel Sender Gauge Assembly *2 Fuel Sub-tank Sub-assembly
*3 Fuel Suction Plate Sub-assembly - -




iii.

Align the protrusions of the fuel suction tube with pump and gauge assembly with the notches in the fuel tank assembly.



Hide 77144 2.INSTALL FUEL PUMP GAUGE RETAINER

a.

Install the fuel pump gauge retainer.

A456994C02
1.167,0.406 1.635,0.406 true 1.208,0.719 1.552,0.719 true 2.5,0.823 2.813,0.698 true 2.708,1.01 2.927,1.01 true 2.396,1.25 2.594,1.396 true 1.375,2.438 2.24,2.125 true 4.969,0.667 5.333,0.75 false 5.229,1.333 5.615,1.083 false 5.438,1.469 5.75,1.344 true 5.51,1.927 5.823,1.802 true 5.177,2.469 5.406,2.219 true 4.635,2.385 4.844,2.188 true 6.594,2.729 6.188,2.417 true 2.563,4.094 2.781,4.094 true 3.198,4.094 3.448,4 true 2.281,2.052 2.594,2.208 0.313,0.156 10 false *a 2.948,0.938 3.146,1.094 0.198,0.156 10 true *b 0.979,0.625 1.177,0.802 0.198,0.177 10 true *c 0.896,0.302 1.115,0.469 0.219,0.167 10 true *d 4.771,0.594 5.083,0.75 0.313,0.156 10 false *e 5.667,0.979 5.979,1.135 0.313,0.156 10 false *f 3.49,3.906 3.667,4.063 0.177,0.156 10 true *g 2.333,4.01 2.531,4.208 0.198,0.198 10 true *h 2.833,0.615 3.052,0.781 0.219,0.167 10 true *d 2.625,1.313 2.823,1.49 0.198,0.177 10 true *c 5.792,1.271 5.99,1.427 0.198,0.156 10 true *b 5.854,1.708 6.031,1.885 0.177,0.177 10 true *d 6.635,2.656 6.948,2.813 0.313,0.156 10 false *a 5.073,2.49 5.271,2.667 0.198,0.177 10 true *c 4.406,2.292 4.604,2.448 0.198,0.156 10 true *b 0.427,0.073 0.781,0.365 0.354,0.292 18 true i, ii 2.26,2.406 2.615,2.698 0.354,0.292 18 false iii 1.875,3.031 2.229,3.323 0.354,0.292 18 false v 4.333,0.115 4.688,0.406 0.354,0.292 18 false iv
*a Insertion Point *b SST (Plate)
*c SST (Claw) *c SST (Bolt)
*e SST (Handle) *f Extension Bar
*g Triangle Mark (Fuel Pump Gauge Retainer) *h Triangle Mark (Fuel Tank Assembly)
V100136

Front Side of Vehicle -


i.

While pressing down on the fuel suction tube with pump and gauge assembly, temporarily install the fuel pump gauge retainer.


ii.

Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.

SST
09808-01071  
09808-14031  (09808-01030, 09808-01090)

HINT:

Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.



iii.

While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).


iv.

Install SST (handle) and an extension bar to SST (plate).

SST
09808-01071  
09808-14031  (09808-01010)


v.

Using SST, rotate the fuel pump gauge retainer so that the triangle mark on the fuel pump gauge retainer is aligned with the triangle mark on the fuel tank assembly to install the fuel suction tube with pump and gauge assembly to the fuel tank assembly.

NOTICE:
·

Do not use any tools other than specified as this may result in damage to the fuel pump gauge retainer or fuel tank assembly.

·

Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.

·

Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.

·

Do not spin SST too fast or use an impact wrench as this may result in damage to components.

·

If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.

·

Make sure that the fuel suction tube set gasket does not come off.





Hide 77209F 3.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A461430C02
4.333,0.917 5.417,1.708 1.083,0.792 5.5,0.917 6.583,1.708 1.083,0.792 1.833,1.042 2.125,1.042 true 1.052,1.354 1.344,1.354 true 5.021,0.469 4.802,0.698 false 5.677,0.365 6.021,0.365 false 5.563,0.531 6.042,0.531 true 5.563,0.458 5.865,0.458 5.865,0.458 5.865,0.531 true 4.979,1.198 5.135,1.198 false 6.063,1.24 6.219,1.24 false 5.917,1.219 6.177,1.052 true 4.813,1.281 5.073,1.5 true 4.604,0.646 4.917,0.802 0.313,0.156 10 false *1 0.802,1.271 1.042,1.427 0.24,0.156 10 true *2 2.146,0.969 2.365,1.135 0.219,0.167 10 true *3 6.063,0.458 6.375,0.615 0.313,0.156 10 false *a 4.375,0.938 4.688,1.094 0.313,0.156 10 false *b 5.552,0.938 5.865,1.094 0.313,0.156 10 false *c 6.208,0.979 6.521,1.135 0.313,0.156 10 false *d 6.052,0.292 6.292,0.448 0.24,0.156 10 true *2 5.177,1.135 5.385,1.313 0.208,0.177 10 true *2 6.25,1.177 6.49,1.333 0.24,0.156 10 true *2 5.115,1.438 5.427,1.594 0.313,0.156 10 false *d 0.458,0.083 0.74,0.438 0.281,0.354 18 false i
*1 Fuel Suction Plate Sub-assembly *2 Tube Joint Clip
*3 Fuel Tank Main Tube Sub-assembly - -
*a Fuel Tube Joint *b O-ring
*c Correct *d Incorrect
V100135

Insert
V100136

Insert


i.

Push the fuel tube joint of fuel tank main tube sub-assembly onto the plug of the fuel suction plate sub-assembly, then install the tube joint clip.

NOTICE:
·

Check that there are no scratches or foreign matter around the connecting parts of the fuel tube joint and plug before performing this work.

·

Check that the fuel tube joint is securely inserted to the end.

·

Check that the tube joint clip is on the collar of the fuel tube joint.

·

After installing the tube joint clip, check that the fuel tank main tube sub-assembly is securely connected by pulling on it.





Hide 77701W 4.CONNECT NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY

Hide 77027B 5.CONNECT NO. 1 FUEL EMISSION TUBE SUB-ASSEMBLY

Hide 58325E 6.INSTALL REAR FLOOR SERVICE HOLE COVER

a.
A458639N01
6.021,3.26 6.385,3.135 true 6.417,3.042 6.729,3.198 0.313,0.156 10 false *a 0.479,0.115 0.917,0.427 0.438,0.313 18 false i, ii 3.927,0.135 4.208,0.49 0.281,0.354 18 false i 0.229,2.969 0.51,3.323 0.281,0.354 18 false iii 4.135,2.958 4.417,3.313 0.281,0.354 18 false iv

i.

Remove any remaining butyl tape from the rear floor service hole cover and vehicle body.


ii.

Clean the installation surfaces of the rear floor service hole cover and vehicle body.


iii.

Connect the 2 fuel suction tube with pump and gauge assembly connectors.


iv.

Install the rear floor service hole cover with new butyl tape.

NOTICE:

Securely install the rear floor service hole cover.




Hide 7.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 9.INSTALL REAR SEAT ASSEMBLY

Hide 10. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 11.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION