Home › Engine / Hybrid System › M15A-FKS (ENGINE MECHANICAL) › REAR CRANKSHAFT OIL SEAL › 2020.08–2021.07
RM3700E _51 Engine / Hybrid System _093330 M15A-FKS ENGINE MECHANICAL _0440538 REAR CRANKSHAFT OIL SEAL A

M15A-FKS ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
A475108N02
5.219,3.125 6.135,3.292 0.917,0.167 5.177,3.083 6.177,3.333 1,0.25 2.385,1.583 2.563,1.417 2.563,1.417 2.74,1.417 false 3.917,2.927 3.917,3.052 false 5.583,2.073 5.583,1.74 false 4.625,2.969 4.677,3.219 4.677,3.219 4.792,3.219 false 3.135,2.302 3.135,2.427 false 5.521,2.083 5.802,2.438 0.281,0.354 18 false 4 3.979,3.073 4.26,3.427 0.281,0.354 18 false 3 3.229,1.281 3.51,1.635 0.281,0.354 18 false 1 4.844,3.135 5.271,3.333 0.427,0.198 10 false ● ★ 5.26,3.135 6.49,3.292 1.229,0.156 8 false 150 (1530, 111) 3.188,2.51 3.469,2.865 0.281,0.354 18 false 2 3.073,1.344 3.5,1.542 0.427,0.198 10 false ● 4.76,2.833 5.042,3.188 0.281,0.354 10 false x8

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR ENGINE OIL SEAL 11401L (Click here) - -
2 NO. 1 CRANKSHAFT POSITION SENSOR PLATE 19315 (Click here) - -
3 DRIVE PLATE AND RING GEAR SUB-ASSEMBLY 32101B (Click here) - -
4 CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY 30400 - - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf)
V100146

N*m (kgf*cm, ft.*lbf): Specified torque
V100135

MP grease ● Non-reusable part
★ Precoated part - -

CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 11401L 1.INSTALL REAR ENGINE OIL SEAL

a.
A461538C01
2.167,0.833 3.083,0.646 true 2.167,0.833 2.698,1.208 true 2.26,0.052 2.542,0.406 0.281,0.354 18 false ii 0.479,0.042 0.76,0.396 0.281,0.354 18 false i 6.01,0.219 6.323,0.417 0.313,0.198 10 false *a 1.885,0.771 2.198,0.969 0.313,0.198 10 false SST
*a -0.9 to 1.1 mm - -


i.

Apply MP grease to the lip of a new rear engine oil seal.

NOTICE:
·

Keep the lip free from foreign matter.

·

Do not allow MP grease to contact the dust seal.




ii.

Using SST and a hammer, tap in the rear engine oil seal.

SST
09223-15030  
09950-70010  (09951-07150)

Standard Depth:

-0.9 to 1.1 mm (-0.0354 to 0.0433 in.) (From the edge of the cylinder block sub-assembly and stiffening crankcase assembly)


NOTICE:

Do not tap in the rear engine oil seal at an angle.




Hide 19315 2.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Z101186

HINT:

Align the pin hole of the No. 1 crankshaft position sensor plate with the pin of the crankshaft.



a.
A460241


Hide 32101B 3.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.
A461542C01
0.917,0.917 1.594,0.583 false 0.917,0.917 1.74,0.875 false 1.313,4.656 1.677,4.458 false 1.729,5.135 2.094,4.938 false 2.594,4.885 2.448,4.51 false 0.625,0.885 1.083,1.083 0.458,0.198 10 false SST 0.469,0.083 0.75,0.438 0.281,0.354 18 false i 0.49,2 0.771,2.354 0.281,0.354 18 false ii 4.26,0.115 4.542,0.469 0.281,0.354 18 false iii 1.51,5.125 1.823,5.323 0.313,0.198 10 false *1 2.573,4.927 2.885,5.125 0.313,0.198 10 false *2 1.073,4.667 1.385,4.865 0.313,0.198 10 false *3 5.531,0.698 5.688,0.906 0.156,0.208 10 true 1 5.531,1.938 5.688,2.146 0.156,0.208 10 true 2 4.927,1.344 5.083,1.552 0.156,0.208 10 true 3 6.094,1.313 6.25,1.521 0.156,0.208 10 true 4 5.063,0.823 5.219,1.031 0.156,0.208 10 true 5 5.979,1.729 6.135,1.938 0.156,0.208 10 true 6 5.969,0.813 6.125,1.021 0.156,0.208 10 true 7 5.104,1.844 5.26,2.052 0.156,0.208 10 true 8
*1 Drive Plate and Ring Gear Subassembly *2 Rear Drive Plate Spacer
*3 No. 1 Crankshaft Position Sensor Plate - -
V100135

Transaxle Side - -


i.

Using SST, hold the crankshaft pulley assembly.

SST
09213-54015  
09330-00021  


ii.

Install the drive plate and ring gear sub-assembly and rear drive plate spacer to the crankshaft.

NOTICE:
·

Clean the bolt holes.

·

As the rear drive plate spacer, drive plate and ring gear sub-assembly and No. 1 crankshaft position sensor plate are not reversible, be sure to install them so that they are facing in the direction shown in the illustration.




iii.

Install and uniformly tighten the 8 bolts in several steps in the sequence shown in the illustration.

Torque:
150 N*m (1530 kgf*cm, 111 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installing the drive plate and ring gear sub-assembly.