| *A | for Type A | *B | for Type B |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
Toyota Genuine CVT Fluid FE | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part |
|
MP grease |
|
Clutch spline grease |
|
Adhesive 1324 |
| ★ | Precoated part | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 19 | MANIFOLD STAY | 17118 | ( )
|
- | - |
| 20 | RESET MEMORY | - | ( )
|
- | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
The engine assembly with continuously variable transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.
1.INSTALL BREATHER PLUG SUB-ASSEMBLY
|
|
35150B
2.INSTALL TRANSMISSION CASE PLUG ASSEMBLY
for Type A:
Install the transmission case plug assembly to the continuously variable transaxle assembly.
Be careful not to damage the O-ring.
for Type B:
Coat a new O-ring with Toyota Genuine CVTfluid FE and install it to the transmission caseplug assembly.
Ensure that the O-ring is not twisted.
Install the transmission case plug assembly to the continuously variable transaxle assembly.
Be careful not to damage the O-ring.
33823
3.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET
4.INSTALL WIRE HARNESS CLAMP BRACKET
12364B
5.INSTALL NO. 2 ENGINE MOVING CONTROL ROD
| *a | Temporarily Tighten | - | - |
Install the No. 2 engine moving control rod to the continuously variable transaxle assembly with the 3 bolts in the order shown in the illustration.
51201
6.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
7.INSTALL CVT TYPE T OIL SEAL
| *a | Clean | *b | Depth |
|
MP grease | - | - |
Ensure that there is no dirt or foreign matter on your hands and then apply MP grease to the entire periphery of the lip of a new CVT type T oil seal.
Temporarily install the CVT type T oil seal by pressing it to the installation surface of the oil pump housing by hand.
Be sure to install the CVT type T oil seal in the correct direction.
Clean the CVT type T oil seal contact surface of SST and the area around it.
Using SST and a hammer, drive the CVT type T oil seal in evenly, until it is even with the side surface of the transaxle housing.
-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)
Drive the CVT type T oil seal in gradually, while visually checking that it is even.
After installation, confirm that the CVT type T oil seal has been driven in until it is even with the side surface of the transaxle housing.
Wipe any extra grease off with your hand.
32000A
8.INSTALL TORQUE CONVERTER ASSEMBLY
| *1 | CVT Type T Oil Seal | - | - |
| *a | Matchmark | *b | Key |
| *c | Groove | - | - |
Set the key at the top of the drive sprocket and put a matchmark on the transaxle housing.
Place a matchmark on the torque converter assembly so that the position of its groove is clearly indicated.
The relative positions of the groove (*c) in the sleeve and the setblock will not necessarily be the same as in the illustration.
Align the matchmark on the housing with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.
Install the torque converter assembly to the input shaft while keeping it horizontal.
Do not damage the CVT Type T Oil Seal.
Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.
Install the torque converter assembly to the input shaft while keeping it horizontal.
Do not damage the CVT Type T Oil Seal.
Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the housing and insert the groove of the torque converter assembly into the key of the drive sprocket.
Install the torque converter assembly to the input shaft while keeping it horizontal.
Do not push the torque converter assembly excessively when rotating it.
Do not damage the CVT type T oil seal.
Clean the drive plate and torque converter assembly setting bolt holes.
| *a | Engine Assembly Surface | *b | Drive Plate Surface |
Using a vernier caliper and straightedge, measure the dimension (A) between the set block and the end face of the continuously variable transaxle assembly.
Make sure to deduct the thickness of the straightedge.
Using a vernier caliper and straightedge, measure the dimension (B) between the continuously variable transaxle assembly contact surface of the engine*a and the torque converter assembly contact surfaces of the drive plate*b, and check that dimension (B) is larger than dimension (A).
B = A + 1 mm (0.0394 in.) or more
Make sure to deduct the thickness of the straightedge.
If the continuously variable transaxle assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.
9.INSTALL ENGINE ASSEMBLY
| *A | for Type A | *B | for Type B |
| *1 | Crankshaft | *2 | Torque Converter Assembly Centerpiece |
|
Clutch Spline Grease | - | - |
Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.
Toyota Genuine Clutch Spline Grease or equivalent
Approximately 1 g (0.0353 oz.)
| *1 | Knock Pin | - | - |
Confirm that the 2 knock pins are installed to the engine assembly and are not damaged.
Install the continuously variable transaxle assembly to the engine assembly with the 7 bolts.
Make sure that the wire harness or similar items are not pinched between the contact surfaces.
Do not use excess force when installing the continuously variable transaxle assembly.
When mounting the continuously variable transaxle assembly to the engine assembly, make sure to securely fit the knock pins into the knock holes.
Check that the torque converter assembly rotates.
When tightening the bolts, be sure that the mating surfaces of the engine assembly and the continuously variable transaxle assembly are in close contact with one another.
Bolt (A), (B): Install from continuously variable transaxle assembly side
Bolt (C): Install from engine assembly side
32101G
10.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT
| *a | Adhesive | - | - |
Clean the threads of the 6 drive plate and torque converter assembly setting bolts.
Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 6 drive plate and torque converter assembly setting bolts.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
In order to ensure proper installation of the 6 drive plate and torque converter assembly setting bolts, apply adhesive to the 6 drive plate and torque converter assembly setting bolts and install them within 10 minutes of adhesive application.
Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.
First install the black colored drive plate and torque converter assembly setting bolt, and then the remaining 5 silver colored drive plate and torque converter assembly setting bolts.
11361J
11.INSTALL FLYWHEEL HOUSING UNDER COVER
|
Install in this Direction | - | - |
28100
12.INSTALL STARTER ASSEMBLY
89535B
15.INSTALL TCM
|
|
82121
16.CONNECT ENGINE WIRE
Engage the 3 clamps to connect the engine wire to the front suspension crossmember sub-assembly.
Engage the 3 clamps to connect the engine wire to the continuously variable transaxle assembly.
Connect the engine wire to the continuously variable transaxle assembly with the bolt.
Connect the No. 3 water by-pass hose assembly.
| *1 | Transmission Wire Connector | *2 | Shift Stroke Sensor Connector |
| *3 | Park/Neutral Position Switch Connector | *4 | Transmission Revolution Sensor (NOUT) Connector |
| *5 | TCM Connector | *6 | Transmission Revolution Sensor (NSS) Connector |
| *7 | Oil Pressure Sensor Connector | *8 | Transmission Revolution Sensor (NT) Connector |
|
Install in this Direction | - | - |
Engage the 4 clamps, install the bolt to connect the engine wire to the continuously variable transaxle assembly.
Rotate the lever until the claw of the TCM connector makes a click sound.
Rotate the lever until the claw of the transmission wire connector makes a click sound.
17.REMOVE ENGINE HANGER
18.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE
20.RESET MEMORY