Home › Engine / Hybrid System › M15A-FXE (ENGINE MECHANICAL) › FRONT CRANKSHAFT OIL SEAL
RM3700E _51 Engine / Hybrid System _093331 M15A-FXE ENGINE MECHANICAL _0440546 FRONT CRANKSHAFT OIL SEAL A

M15A-FXE ENGINE MECHANICAL  FRONT CRANKSHAFT OIL SEAL  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
A475435N02
2.802,0.271 3.719,0.438 0.917,0.167 1.969,4.5 2.969,4.667 1,0.167 2.76,0.229 3.76,0.479 1,0.25 1.375,1.573 1.375,1.375 false 2.792,0.76 3.104,0.677 3.104,0.677 3.292,0.677 false 2.917,1.573 3.042,1.573 3.042,1.573 3.146,1.25 false 1.688,2.729 1.958,2.729 false 4.083,3.698 4.354,3.698 false 6.531,0.219 6.802,0.219 false 2.281,0.635 2.635,0.354 2.635,0.354 2.802,0.354 false 2.969,4.594 3.146,4.594 3.146,4.594 3.469,4.385 false 1.438,1.542 1.719,1.896 0.281,0.354 18 false 6 4.427,3.563 4.708,3.917 0.281,0.354 18 false 5 1.458,2.573 1.74,2.927 0.281,0.354 18 false 4 3.646,0.573 3.927,0.927 0.281,0.354 18 false 2 2.76,1.417 3.042,1.771 0.281,0.354 18 false 1 2.073,2.042 2.354,2.396 0.281,0.354 10 false x2 2.865,4.292 3.146,4.646 0.281,0.354 10 false x4 3.49,4.406 3.771,4.76 0.281,0.354 10 false x4 4.073,4.229 4.354,4.583 0.281,0.354 10 false x9 2.594,1.448 2.875,1.802 0.281,0.354 10 false ● 6.333,0.073 6.615,0.427 0.281,0.354 18 false 3 2.854,0.281 3.979,0.51 1.125,0.229 8 false 260 (2651, 192) 2,4.5 3.448,4.729 1.448,0.229 8 false 5.0 (51, 44 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 TIMING CHAIN COVER OIL SEAL 11301C (Click here) - -
2 CRANKSHAFT PULLEY ASSEMBLY 13470 (Click here) - -
3 INSPECT FOR OIL LEAK - (Click here) - -
4 ENGINE UNDER COVER RH 51441C - - -
5 NO. 1 ENGINE UNDER COVER ASSEMBLY 51410 - - -
6 FRONT WHEEL RH - (Click here) - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf)
V100146

N*m (kgf*cm, ft.*lbf): Specified torque
V100135

MP grease ● Non-reusable part

PROCEDURE

Hide 11301C 1.INSTALL TIMING CHAIN COVER OIL SEAL

a.
A462205C01
2.302,0.854 2.698,0.854 true 6.156,0.229 6.417,0.417 0.26,0.188 10 false *a 1.979,0.771 2.323,1.01 0.344,0.24 10 false SST 2.021,0.083 2.323,0.427 0.302,0.344 18 false ii 0.427,0.073 0.729,0.417 0.302,0.344 18 false i
*a 0 to 2 mm - -


i.

Apply MP grease to the lip of a new timing chain cover oil seal.

NOTICE:
·

Keep the lip free from foreign matter.

·

Do not allow MP grease to contact the dust seal.




ii.

Using SST and a hammer, tap in the timing chain cover oil seal.

SST
09223-00010  

Standard Depth:

0 to 2 mm (0 to 0.0787 in.) (From the edge of the No. 2 timing chain cover assembly)


NOTICE:

Do not tap in the timing chain cover oil seal at an angle.




Hide 13470 2.INSTALL CRANKSHAFT PULLEY ASSEMBLY

Z101186

Click here(Click here)

Hide 3.INSPECT FOR OIL LEAK

Z101186

Click here(Click here)

Hide 51441C 4.INSTALL ENGINE UNDER COVER RH

Hide 51410 5.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 6.INSTALL FRONT WHEEL RH

Z101186

Click here(Click here)