| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | STRAIGHT PIN | - | ( )
|
- | - |
| 2 | RING PIN | - | ( )
|
- | - |
| 3 | STUD BOLT | - | ( )
|
- | - |
| *A | w/ Stud Bolt | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part |
|
MP grease |
|
Adhesive 1344 | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
| *T1 | 1st: 50 (510, 37)
2nd: Turn 90° 3rd: Turn 90° |
- | - |
| *A | w/ Stud Bolt | *B | w/o Stud Bolt |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | ★ | Precoated part |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part |
|
Adhesive 1344 |
| ★ | Precoated part | - | - |
This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
1.INSTALL STRAIGHT PIN
|
|
| *a | Protrusion Height | - | - |
Using a plastic hammer, tap in 2 new straight pins to the No. 2 timing chain cover assembly.
5.0 to 7.0 mm (0.197 to 0.276 in.)
2.INSTALL RING PIN
|
|
| *a | Protrusion Height | - | - |
Using a plastic hammer, tap in 6 new ring pins to the stiffening crankcase assembly.
3.5 to 4.5 mm (0.138 to 0.177 in.)
Using a plastic hammer, tap in 8 new ring pins to the camshaft housing sub-assembly.
3.2 to 4.3 mm (0.126 to 0.169 in.)
3.INSTALL STUD BOLT
|
|
| *A | w/ Stud Bolt | - | - |
| *a | 14 mm (0.551 in.) | *b | 13 mm (0.512 in.) |
| *c | 29 mm (1.142 in.) | *d | 21 mm (0.827 in.) |
| *e | 9 mm (0.354 in.) | *f | 34 mm (1.339 in.) |
| *g | 19 mm (0.748 in.) | - | - |
Using an E8 "TORX" socket wrench, install the stud bolt to the cylinder head sub-assembly.
Using an E6 "TORX" socket wrench, install the stud bolt to the timing chain cover assembly.
Using an E6 "TORX" socket wrench, install the 2 stud bolts to the stiffening crankcase assembly
4.INSTALL STRAIGHT SCREW PLUG
Using a 10 mm hexagon socket wrench, install the straight screw plug to the stiffening crankcase assembly.
11420
5.INSTALL STIFFENING CRANKCASE ASSEMBLY
|
|
| *a | Seal Packing | *b | Bolt Type |
| *c | Tightening Order | - | - |
Apply seal packing in a continuous line as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
2.5 to 3.5 mm (0.0984 to 0.138 in.)
Install the stiffening crankcase assembly within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.
Do not add engine oil for at least 2 hours after the installation.
Make sure that the diameter at the start and end of each line of seal packing is 5 +/- 2 mm (0.197 +/- 0.0787 in.).
After installation, if the seal packing has seeped out, wipe it off.
Do not start the engine for at least 2 hours after installation.
Temporarily install the stiffening crankcase assembly with the 8 bolts.
| Item | Length |
|---|---|
| Bolt (A) | 170 mm (6.69 in.) |
| Bolt (B) | 120 mm (4.72 in.) |
| Bolt (C) | 40 mm (1.57 in.) |
Tighten the 8 bolts in the order shown in the illustration to install the stiffening crankcase assembly.
15104
7.INSTALL OIL STRAINER SUB-ASSEMBLY
Apply a light coat of engine oil to a new oil strainer gasket.
Install the oil strainer gasket to the oil strainer sub-assembly.
Using an 8 mm socket wrench, install the oil strainer sub-assembly to the stiffening crankcase assembly with the bolt.
12101
8.INSTALL OIL PAN SUB-ASSEMBLY
|
|
| *a | Seal Packing | *b | 4.5 mm (0.177 in.) |
| *c | 2.5 to 3.5 mm (0.0984 to 0.138 in.) | *d | Nut |
Apply seal packing in a continuous line as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
2.5 to 3.5 mm (0.0984 to 0.138 in.)
Install the oil pan sub-assembly within 3 minutes and tighten the bolts and nuts within 10 minutes of applying seal packing.
Do not add engine oil for at least 2 hours after the installation.
Do not start the engine for at least 2 hours after installation.
Make sure that the diameter at the start and end of each line of seal packing is 5 +/- 2 mm (0.197 +/0.0787 in.).
Install the oil pan sub-assembly with the 9 bolts and 2 nuts in several steps in the order shown in the illustration.
12101A
9.INSTALL OIL PAN DRAIN PLUG
15600A
10.INSTALL OIL FILTER UNION
Using a 12 mm hexagon socket wrench, install the oil filter union to the stiffening crankcase assembly.
11445
13.INSTALL CYLINDER BLOCK WATER JACKET SPACER
11101
15.INSTALL CYLINDER HEAD SUB-ASSEMBLY
The cylinder head set bolts are tightened in 3 progressive steps.
Perform inspection after repair after replacing the cylinder head sub-assembly.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| *a | Paint Mark | - | - |
|
Front of Engine | - | - |
Place the cylinder head sub-assembly on the cylinder block sub-assembly.
Ensure that the contact surface of the cylinder head sub-assembly is free of oil.
Place the cylinder head sub-assembly on the cylinder block sub-assembly gently in order not to damage the cylinder head gasket with the bottom of the cylinder head sub-assembly.
Apply a light coat of engine oil to the threads and under the heads of the cylinder head set bolts.
Install the 8 plate washers to the 8 cylinder head set bolts.
Be careful not to drop the plate washers into the cylinder head sub-assembly.
| Item | Length |
|---|---|
| Bolt (A) | 129.1 to 130.9 mm (5.08 to 5.15 in.) |
| Bolt (B) | 139.1 to 140.9 mm (5.48 to 5.55 in.) |
Step 1:
1. Using a 12 mm socket wrench, install and uniformly tighten the 8 cylinder head set bolts in several steps in the order shown in the illustration.
Mark each cylinder head set bolt head with paint as shown in the illustration.
Step 2:
1. Tighten the cylinder head set bolts 90° in the order shown in step 1.
Step 3:
1. Tighten the cylinder head set bolts another 90° in the order shown in step 1.
2. Check that the paint marks are now facing rearward.
13716
16.INSTALL VALVE STEM CAP
Apply a light coat of engine oil to the valve stem cap ends.
Install the 12 valve stem caps to the cylinder head sub-assembly.
Install the same parts in the same combination to their original locations.
Do not drop the valve stem caps into the cylinder head sub-assembly.
13750
17.INSTALL VALVE LASH ADJUSTER ASSEMBLY
Inspect the 12 valve lash adjuster assemblies before installing them.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION
Install the 12 valve lash adjuster assemblies to the cylinder head sub-assembly.
Install the same parts in the same combination to their original locations.
13801
18.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
| *1 | No. 1 Valve Rocker Arm Sub-assembly | *2 | Valve Lash Adjuster Assembly |
| *3 | Valve Stem Cap | - | - |
Install the 12 No. 1 valve rocker arm sub-assemblies as shown in the illustration.
Apply engine oil to the valve lash adjuster assembly tips and valve stem caps.
Install the same parts in the same combination to their original locations.
13502B
19.INSTALL EXHAUST CAMSHAFT SUB-ASSEMBLY
|
|
Clean the camshaft journals and camshaft housing sub-assembly.
Install the exhaust camshaft sub-assembly to the camshaft housing sub-assembly.
Apply a light coat of engine oil to the camshaft journals and camshaft housing sub-assembly.
13501A
20.INSTALL INTAKE CAMSHAFT SUB-ASSEMBLY
|
|
Clean the camshaft journals and camshaft housing sub-assembly.
Install the intake camshaft sub-assembly to the camshaft housing sub-assembly.
Apply a light coat of engine oil to the camshaft journals and camshaft housing sub-assembly.
21.INSTALL CAMSHAFT BEARING CAP
| *a | 2 | *b | 3 to 4 |
Place the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap and No. 3 camshaft bearing caps and No. 4 camshaft bearing cap in their correct locations.
Uniformly tighten the 7 bolts in the order shown in the illustration.
11103
22.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY
|
|
| *1 | No. 1 Valve Rocker Arm Sub-assembly | *2 | Valve Stem Cap |
| *3 | Valve Lash Adjuster Assembly | - | - |
| *a | Incorrect | *b | Correct |
| *c | Seal Packing | *d | 15° to 45° |
| *e | 102° to 132° | - | - |
Check that the No. 1 valve rocker arm sub-assemblies are installed as shown in the illustration.
Apply seal packing in a continuous line as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
3.0 to 4.0 mm (0.118 to 0.157 in.)
Remove any oil from the contact surfaces.
Install the camshaft housing sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.
Do not start the engine for at least 2 hours after installation.
Make sure that the diameter at the start and end of each line of seal packing is 5 +/- 2 mm (0.197 +/- 0.0787 in.).
Position the knock pins of the intake camshaft sub-assembly and exhaust camshaft sub-assembly as shown in the illustration.
Temporarily install the camshaft housing sub-assembly with the 14 bolts.
| Item | Length |
|---|---|
| Bolt (A) | 40 mm (1.57 in.) |
| Bolt (B) | 65 mm (2.56 in.) |
Install the camshaft housing sub-assembly, and then tighten the 14 bolts in several steps in the order shown in the illustration.
Do not add engine oil for at least 2 hours after installation.
Do not start the engine for at least 2 hours after installation.
After installation, if the seal packing has seeped out, wipe it off.
13471A
23.INSTALL CRANKSHAFT TIMING GEAR KEY
Using a plastic hammer, tap in the 2 crankshaft timing gear keys.
Tap in the crankshaft timing gear keys until they contact the crankshaft as shown in the illustration.
13478
24.INSTALL CRANKSHAFT PULLEY SPACER
11310
25.INSTALL TIMING CHAIN COVER ASSEMBLY
| *a | Timing Chain Cover Assembly Side | *b | Engine Assembly Side |
Clean the contact surfaces of the timing chain cover assembly, cylinder head sub-assembly, camshaft housing sub-assembly, cylinder block sub-assembly and stiffening crankcase assembly, and confirm that no oil, moisture, or other foreign matter is on the surfaces.
| *a | 2.5 to 3.5 mm (0.0984 to 0.138 in.) | *b | 2.0 to 6.0 mm (0.0787 to 0.236 in.) |
| *c | 10 mm (0.394 in.) | *d | 30 mm (1.181 in.) |
| *e | 20 mm (0.787 in.) | *f | 344.2 mm (1.13 ft.) |
| *g | 4.0 to 6.0 mm (0.157 to 0.236 in.) | *h | 3.0 to 4.0 mm (0.118 to 0.157 in.) |
|
Seal Packing | - | - |
Apply seal packing in a continuous line to the timing chain cover assembly as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
Clean the surfaces with non-residue solvent before applying seal packing.
Install the timing chain cover assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.
Do not add oil for at least 2 hours after installation.
Do not start the engine for at least 2 hours after installation.
Make sure that the diameter at the start and end of each line of seal packing is 5 +/- 2 mm (0.197 +/- 0.0787 in.).
Temporarily install the timing chain cover assembly with the 20 bolts.
Make sure there is no oil on the bolts. If oil is found on any bolt, clean it before installation.
| Bolt | Length |
|---|---|
| Bolt (A) | 30 mm (1.18 in.) |
| Bolt (B) | 45 mm (1.77 in.) |
Tighten the 20 bolts in the order shown in the illustration.
13070A
26.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
Perform inspection after repair after replacing the camshaft timing exhaust gear assembly.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| *a | Knock Pin Hole | *b | Knock Pin |
Align and fit the knock pin of the exhaust camshaft sub-assembly to the knock pin hole of the camshaft timing exhaust gear assembly.
Using a wrench, hold the hexagonal portion of the exhaust camshaft sub-assembly.
Be careful not to damage the cylinder head sub-assembly or spark plug tube with the wrench.
Do not disassemble the camshaft timing exhaust gear assembly.
Using a 5 mm hexagon socket wrench, install the camshaft timing exhaust gear assembly with the 3 bolts and install the camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly).
27.SET NO. 1 CYLINDER TO TDC (COMPRESSION)
| *a | 95° | *b | Timing Mark |
Temporarily install the crankshaft pulley bolt.
Rotate the crankshaft 95° counterclockwise to position the crankshaft timing gear key as shown in the illustration.
Check that the timing marks of the camshaft timing exhaust gear assembly and camshaft timing gear assembly are as shown in the illustration.
13561
28.INSTALL NO. 1 CHAIN VIBRATION DAMPER
13559
29.INSTALL CHAIN TENSIONER SLIPPER
13540
30.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY
|
|
13521
31.INSTALL CRANKSHAFT TIMING GEAR OR SPROCKET
13506
32.INSTALL CHAIN SUB-ASSEMBLY
| *a | Paint Mark (Yellow) | *b | Timing Mark |
| *c | Paint Mark (Orange) | - | - |
|
Turn | - | - |
Remove the crankshaft pulley bolt.
Install the crankshaft timing sprocket and chain sub-assembly.
Align the paint mark (yellow) of the chain sub-assembly with the timing mark of the crankshaft timing sprocket and install the chain sub-assembly to the crankshaft timing sprocket.
Using the hexagonal portion of the exhaust camshaft sub-assembly, rotate the exhaust camshaft sub-assembly counterclockwise with a wrench, align the timing mark of the camshaft timing exhaust gear assembly with the paint mark (orange) of the chain sub-assembly, and install the chain sub-assembly to the camshaft timing exhaust gear assembly.
13050
33.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY
Perform inspection after repair after replacing the camshaft timing gear assembly.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| *a | Loosen | *b | Paint Mark (Orange) |
| *c | Timing Mark | *d | Knock Pin Hole |
| *e | Knock Pin | *f | Hold |
|
Turn | - | - |
Hold the hexagonal portion of the exhaust camshaft sub-assembly with a wrench and turn the camshaft timing exhaust gear assembly clockwise to loosen the chain sub-assembly between the camshaft timing exhaust gear assembly and crankshaft timing sprocket as shown in the illustration.
Align the paint mark (orange) of the chain sub-assembly with the timing mark of the camshaft timing gear assembly and install the chain sub-assembly to the camshaft timing gear assembly.
Align and fit the knock pin of the intake camshaft sub-assembly to the knock pin hole of the camshaft timing gear assembly.
Using a wrench, hold the hexagonal portion of the intake camshaft sub-assembly.
Be careful not to damage the camshaft housing sub-assembly, cylinder head sub-assembly or spark plug tube with the wrench.
Using a 10 mm bi-hexagonal wrench, install the camshaft timing gear assembly with the bolt.
Remove the hexagon wrench with the No. 1 chain tensioner assembly.
13519
35.INSTALL OIL PUMP DRIVE GEAR
11193
39.INSTALL SPARK PLUG TUBE GASKET
Install 3 new spark plug tube gaskets to the cylinder head cover sub-assembly.
11102A
40.INSTALL CAMSHAFT POSITION SENSOR
11201
41.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
| *a | Seal Packing Diameter: 3.0 to 6.0 mm (0.118 to 0.236 in.) | *b | Mark |
|
Seal Packing | - | - |
Apply a light coat of engine oil to the new camshaft bearing cap oil hole gasket.
Install a new camshaft bearing cap oil hole gasket to the No. 1 camshaft bearing cap.
Install 5 new cylinder head cover gaskets to the cylinder head cover sub-assembly.
Apply seal packing as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
3.0 to 6.0 mm (0.118 to 0.236 in.)
Remove any oil from the contact surfaces.
Install the cylinder head cover subassembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.
Install the cylinder head cover sub-assembly to the camshaft housing sub-assembly.
Temporarily install the cylinder head cover sub-assembly and camshaft position sensor with the 15 bolts.
| Bolt | Length | Thread Diameter |
|---|---|---|
| Bolt (A) | 23.5 mm (0.925 in.) | 6 mm (0.24 in.) |
| Bolt (B) | 30 mm (1.18 in.) | 6 mm (0.24 in.) |
Using an 8 mm socket wrench, install the 2 camshaft position sensors (for Exhaust Side and for Intake Side) and cylinder head cover sub-assembly with 4 new bolts (B) and the 11 bolts (A) in the order shown in the illustration.
Do not add oil for at least 2 hours after installation.
Do not start the engine for at least 2 hours after installation.
16305E
42.INSTALL OUTLET WATER BY-PASS SUB-ASSEMBLY
Using an 8 mm socket wrench, install the outlet water by-pass sub-assembly and a new outlet water pipe gasket to the cylinder head sub-assembly with the 2 bolts.
16304
43.INSTALL OUTLET WATER SUB-ASSEMBLY
Using an 8 mm socket wrench, install the outlet water sub-assembly and a new outlet water gasket to the cylinder head sub-assembly with the 2 bolts.
13470
44.INSTALL CRANKSHAFT PULLEY ASSEMBLY
| *a | Hold | *b | Turn |
Align the crankshaft timing gear key with the key groove of the crankshaft pulley assembly.
Using SST, hold the crankshaft pulley assembly and install the crankshaft pulley set bolt.
12204C
45.INSTALL PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)
12108A
47.INSTALL OIL FILLER CAP GASKET
12180E
48.INSTALL OIL FILLER CAP ASSEMBLY