Home › Engine / Hybrid System › M15A-FXE (ENGINE MECHANICAL) › REAR CRANKSHAFT OIL SEAL
RM3700E _51 Engine / Hybrid System _093331 M15A-FXE ENGINE MECHANICAL _0440547 REAR CRANKSHAFT OIL SEAL A

M15A-FXE ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
A462232N03
4.833,2.479 5.698,2.646 0.865,0.167 5.438,3.115 6.188,3.281 0.75,0.167 4.792,2.438 5.74,2.688 0.948,0.25 6,2.75 6,2.5 false 2.25,1.792 2.448,1.479 2.448,1.479 2.625,1.479 false 2.927,2.094 3.063,1.771 3.063,1.771 3.229,1.771 false 3.656,2.292 3.917,2.052 3.917,2.052 4.094,2.052 false 4.156,3.542 4.417,3.542 false 4.104,2.781 4.302,2.542 4.302,2.542 4.427,2.542 false 5.427,3.198 5.229,3.198 false 5.938,2.781 6.219,3.135 0.281,0.354 18 false 5 3.927,3.427 4.208,3.781 0.281,0.354 18 false 4 4.458,1.958 4.74,2.313 0.281,0.354 18 false 3 3.615,1.625 3.896,1.979 0.281,0.354 18 false 2 3.24,1.292 3.521,1.646 0.281,0.354 18 false 1 5.104,3.271 5.385,3.625 0.281,0.354 10 false x6 4.125,2.792 4.406,3.146 0.281,0.354 10 false x8 3.031,1.333 3.313,1.688 0.281,0.354 10 false ● 4.479,2.448 4.979,2.688 0.5,0.24 10 false ● ★ 5.521,3.125 6.635,3.385 1.115,0.26 8 false 30 (306, 22) 4.844,2.479 6.083,2.729 1.24,0.25 8 false 150 (1530, 111)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR ENGINE OIL SEAL 11401L (Click here) - -
2 NO. 1 CRANKSHAFT POSITION SENSOR PLATE 19315 (Click here) - -
3 FLYWHEEL SUB-ASSEMBLY 13405 (Click here) - -
4 TRANSMISSION INPUT DAMPER ASSEMBLY 31270 (Click here) - -
5 HYBRID VEHICLE TRANSAXLE ASSEMBLY 30900 - - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf)
V100146

N*m (kgf*cm, ft.*lbf): Specified torque
V100135

MP grease ● Non-reusable part
★ Precoated part - -

CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 11401L 1.INSTALL REAR ENGINE OIL SEAL

a.
A461538C01
2.167,0.833 3.083,0.646 true 2.167,0.833 2.698,1.208 true 2.26,0.052 2.542,0.406 0.281,0.354 18 false ii 0.479,0.042 0.76,0.396 0.281,0.354 18 false i 6.01,0.219 6.323,0.417 0.313,0.198 10 false *a 1.885,0.771 2.198,0.969 0.313,0.198 10 false SST
*a -0.9 to 1.1 mm - -


i.

Apply MP grease to the lip of a new rear engine oil seal.

NOTICE:
·

Keep the lip free from foreign matter.

·

Do not allow MP grease to contact the dust seal.




ii.

Using SST and a hammer, tap in the rear engine oil seal.

SST
09223-15030  
09950-70010  (09951-07150)

Standard Depth:

-0.9 to 1.1 mm (-0.0354 to 0.0433 in.) (From the edge of the cylinder block sub-assembly and stiffening crankcase assembly)


NOTICE:

Do not tap in the rear engine oil seal at an angle.




Hide 19315 2.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Z101186

HINT:

Align the pin hole of the No. 1 crankshaft position sensor plate with the pin of the crankshaft.



a.
A460241


Hide 13405 3.INSTALL FLYWHEEL SUB-ASSEMBLY

a.
A462234N01
1.313,0.854 0.76,0.896 0.76,0.896 1.083,0.5 true 0.365,0.021 0.646,0.375 0.281,0.354 18 false i 4.156,0.052 4.344,0.344 0.188,0.292 18 true ii 0.427,0.833 0.844,1.104 0.417,0.271 10 false SST 5.813,0.313 5.938,0.49 0.125,0.177 10 true 1 4.979,1.229 5.104,1.406 0.125,0.177 10 true 2 5.979,0.771 6.104,0.948 0.125,0.177 10 true 3 4.844,0.802 4.969,0.979 0.125,0.177 10 true 4 5.844,1.219 5.969,1.396 0.125,0.177 10 true 5 5.031,0.302 5.156,0.479 0.125,0.177 10 true 6 5.438,1.385 5.563,1.563 0.125,0.177 10 true 7 5.417,0.167 5.542,0.344 0.125,0.177 10 true 8 6.49,0.25 6.74,0.542 0.25,0.292 18 true iii

i.

Using SST, hold the crankshaft pulley assembly.

SST
09213-54015  
09330-00021  


ii.

Clean the bolt holes.


iii.

Install the flywheel sub-assembly with the 8 new bolts. Uniformly tighten the 8 bolts in the order shown in the illustration.

Torque:
150 N*m (1530 kgf*cm, 111 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installing the flywheel sub-assembly.




Hide 31270 4.INSTALL TRANSMISSION INPUT DAMPER ASSEMBLY

a.
A479914N01
1.552,0.917 1.052,0.948 1.052,0.948 1.25,0.469 false 0.438,0.042 0.719,0.396 0.281,0.354 18 false i 4.115,0.073 4.344,0.354 0.229,0.281 18 true ii 0.729,0.896 1.146,1.219 0.417,0.323 10 false SST

i.

Using SST, hold the crankshaft pulley assembly.

SST
09213-54015  
09330-00021  


ii.

Install the transmission input damper assembly to the flywheel sub-assembly with the 6 bolts. Uniformly tighten the 6 bolts in the order shown in the illustration.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)

NOTICE:
·

Make sure that there are no oil on the transmission input damper assembly and flywheel sub-assembly.

·

Make sure to install the transmission input damper assembly in the correct direction.

·

Do not allow grease to contact the splines of the transmission input damper assembly and the input shaft.





Hide 30900 5.INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY