Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441183 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P314779  Transmission (Shaft) Mechanical Linkage Failure  


DTC SUMMARY

Refer to the DTC summary for DTC P1C7779.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1C7779

DESCRIPTION

Refer to the description for DTC P1C7779.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1C7779

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
P314779 Transmission (Shaft) Mechanical Linkage Failure Drive force from motor (MG2) or the engine cannot be transmitted to the wheels.
The engine, generator (MG1), motor (MG2) or hybrid vehicle transaxle assembly does not run smoothly due to a mechanical malfunction.
(1 trip detection logic)
·

Engine

·

Hybrid vehicle transaxle assembly

·

Transmission input damper assembly


Does not come on Master Warning: Comes on Hybrid Control A

Related Data List
DTC No. Data List
P314779
·

Generator Revolution

·

Motor Revolution

·

Engine Speed



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON (READY).

4.

Drive the vehicle at approximately 30 km/h (19 mph) or more for approximately 5 seconds or more using the engine.

5.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

6.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




CAUTION / NOTICE / HINT

HINT:
·

A seized engine, mechanical malfunction of the hybrid vehicle transaxle can be suspected.

·

If this DTC is output, the engine or gears in the transaxle may have seized or foreign matter have been caught in either of them. Therefore, check the engine oil, hybrid transaxle fluid, coolant (for Engine) and coolant (for Inverter) levels.



PROCEDURE

1.CHECK DTC OUTPUT (ENGINE)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
No DTCs in the table below are output A
Any of the DTCs in the table below are output B


Relevant DTC
P03352A Crankshaft Position Sensor "A" Signal Stuck in Range
P033531 Crankshaft Position Sensor "A" No Signal
P033562 Crankshaft Position Sensor "A" Signal Compare Failure


Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK CRANKSHAFT PULLEY REVOLUTION (P POSITION)

B

2.CHECK CRANKSHAFT PULLEY REVOLUTION (P POSITION)

OK

3.CLEAR DTC

NG

7.CHECK CRANKSHAFT PULLEY REVOLUTION (N POSITION)
3.CLEAR DTC

NEXT

4.CHECK ENGINE RACING
4.CHECK ENGINE RACING

OK

5.CHECK CREEP MOVEMENT

NG

5.CHECK CREEP MOVEMENT

OK

6.INSPECT ENGINE SPEED

NG

6.INSPECT ENGINE SPEED

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1C7779

Result:
Result Proceed to
The absolute value of the difference is less than 500 rpm A
The absolute value of the difference is 500 rpm or more continuously for 1 second B



A

B

7.CHECK CRANKSHAFT PULLEY REVOLUTION (N POSITION)

OK

NG

REPAIR OR REPLACE ENGINE