Home › Engine / Hybrid System › M15A-FXE (ENGINE MECHANICAL) › REAR CRANKSHAFT OIL SEAL › 2020.08–2021.07
RM3700E _51 Engine / Hybrid System _093331 M15A-FXE ENGINE MECHANICAL _0440547 REAR CRANKSHAFT OIL SEAL A

M15A-FXE ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A462231N01
6,2.75 6,2.5 false 2.25,1.792 2.448,1.479 2.448,1.479 2.625,1.479 false 2.927,2.094 3.156,1.802 3.156,1.802 3.333,1.802 false 3.656,2.292 3.917,2.052 3.917,2.052 4.094,2.052 false 4.156,3.542 4.417,3.542 false 4.104,2.781 4.365,2.542 4.365,2.542 4.542,2.542 false 5.938,2.781 6.219,3.135 0.281,0.354 18 false 1 3.927,3.427 4.208,3.781 0.281,0.354 18 false 2 4.458,1.958 4.74,2.313 0.281,0.354 18 false 3 3.427,1.656 3.708,2.01 0.281,0.354 18 false 4 3.24,1.344 3.521,1.698 0.281,0.354 18 false 5 5.24,3.229 5.521,3.583 0.281,0.354 10 false x6 4.125,2.792 4.406,3.146 0.281,0.354 10 false x8 3.031,1.417 3.313,1.771 0.281,0.354 10 false ● 4.646,2.479 5.146,2.719 0.5,0.24 10 false ● ★

Procedure Part Name Code
Z101186

Z101188

Z101187

1 HYBRID VEHICLE TRANSAXLE ASSEMBLY 30900 - - -
2 TRANSMISSION INPUT DAMPER ASSEMBLY 31270 (Click here) - -
3 FLYWHEEL SUB-ASSEMBLY 13405 (Click here) - -
4 NO. 1 CRANKSHAFT POSITION SENSOR PLATE 19315 - - -
5 REAR ENGINE OIL SEAL 11401L (Click here) - -

● Non-reusable part ★ Precoated part

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear engine oil seal removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Reconnected to auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
·

Air leaks from intake system

·

Gas leaks from exhaust system


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 30900 1.REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY

Hide 31270 2.REMOVE TRANSMISSION INPUT DAMPER ASSEMBLY

a.
A479914N02
1.552,0.885 0.635,0.771 0.635,0.771 1.323,0.521 false 0.302,0.719 0.76,0.917 0.458,0.198 10 false SST 0.448,0.052 0.729,0.406 0.281,0.354 18 false i 4.083,0.052 4.333,0.323 0.25,0.271 18 true ii

i.

Using SST, hold the crankshaft pulley assembly.

SST
09213-54015  
09330-00021  


ii.

Remove the 6 bolts and transmission input damper assembly from the flywheel sub-assembly.



Hide 13405 3.REMOVE FLYWHEEL SUB-ASSEMBLY

a.
A461536N02
0.427,0.01 0.708,0.365 0.281,0.354 18 false i 4.104,0.021 4.385,0.375 0.281,0.354 18 false ii

i.

Using SST, hold the crankshaft pulley assembly.

SST
09213-54015  
09330-00021  


ii.

Remove the 8 bolts, rear drive plate spacer, drive plate and ring gear sub-assembly.



Hide 19315 4.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

a.
A460253


Hide 11401L 5.REMOVE REAR ENGINE OIL SEAL

a.
A460254C01
5.094,0.917 4.771,0.646 true 5.177,0.917 5.49,1.115 0.313,0.198 10 false *a 5.302,0.438 5.656,0.719 0.354,0.281 18 false i 2.031,0.51 2.385,0.792 0.354,0.281 18 false ii
*a Cut Position - -


i.

Using a knife, cut off the lip of the rear engine oil seal.


ii.

Using a screwdriver, pry out the rear engine oil seal.

NOTICE:

Do not damage the surface of the rear engine oil seal press fit hole or the crankshaft.


HINT:

Tape the screwdriver tip before use.