Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441183 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P314A31  Motor Electronics Coolant Pump "A" No Signal  


DESCRIPTION

Refer to the description for DTC P0C7396.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0C7396

The inverter water pump assembly sends the inverter water pump speed (measured value) signal to the hybrid vehicle control ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
P314A31 Motor Electronics Coolant Pump "A" No Signal The inverter water pump speed signal is not sent to the hybrid vehicle control ECU when the ignition switch is turned to ON (READY).*
(1 trip detection logic)
·

Wire harness or connector

·

Hybrid vehicle control ECU

·

Inverter water pump assembly

·

INV W/P fuse

·

IGCT-MAIN fuse

·

IGCT relay


Comes on Master Warning: Comes on Hybrid Control A

*: Either of the following conditions is met.
·

A malfunction (open, short to +B or short to ground) in the speed signal line from the inverter water pump assembly to the hybrid vehicle control ECU is detected.

·

A malfunction in the inverter water pump assembly power source circuit is detected.

·

A malfunction in the +B line is detected.

·

A malfunction in hybrid vehicle control ECU power source circuit is detected.


Related Data List
DTC No. Data List
P314A31
·

Inverter Water Pump Revolution

·

Inverter Water Pump Duty Ratio

·

Ready Signal



Related Active Test
DTC No. Active Test
P314A31 Activate the Inverter Water Pump

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON (READY) and wait for 2 minutes or more.

4.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for DTC P0C7396.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0C7396

PROCEDURE

1.CLEAR DTC

NEXT

2.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE INVERTER WATER PUMP)
2.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE INVERTER WATER PUMP)
NOTICE:
·

Make sure that the HV coolant level is above the low line of the inverter reserve tank.

·

Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.

·

When the inverter water pump assembly signal line (SWP - IWP) is open or its connection is faulty, the inverter water pump assembly is operated forcibly.



HINT:

When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.


Pre-procedure1

a.

None.


Procedure1

a.

Perform the "Activate the Inverter Water Pump" Active Test.

Powertrain > Hybrid Control > Active Test
Tester Display
Activate the Inverter Water Pump
50004 397 1

b.

Touch the inverter water pump assembly and check that it is operating (vibrating).

OK:

The inverter water pump is operating (vibrating).


HINT:

Perform the Active Test with the inverter coolant temperature between -15 and 65°C (5 to 149°F).


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.



OK

3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

NG

9.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)
3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

4.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

4.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

OK

5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)

NG

CONNECT SECURELY

5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)
HINT:

Check the condition (looseness, deterioration, etc.) of the wire to body ground for the inverter water pump assembly.


Pre-procedure1

a.

Disconnect the A68 hybrid vehicle control ECU connector.


b.

Disconnect the A59 inverter water pump assembly connector.


Procedure1

a.
A458567C02
1.51,0.26 1.927,0.531 0.417,0.271 1.49,2.615 1.906,2.865 0.417,0.25 1.844,1.969 2.125,1.521 true 1.417,3.99 1.573,3.604 true 0.25,0.177 0.563,0.333 0.313,0.156 10 false *a 0.271,2.833 0.583,2.99 0.313,0.156 10 false *b 1.198,4.021 1.656,4.219 0.458,0.198 10 false NWP 1.531,1.99 1.99,2.188 0.458,0.198 10 false NIWP 1.604,0.323 1.917,0.479 0.313,0.156 10 false A68 1.583,2.667 1.896,2.823 0.313,0.156 10 false A59
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Inverter Water Pump Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition

Click Location & Routing(A68,A59)Location & Routing

Click Connector(A68)Instrument Panel>Engine Room Main Wire>Hybrid Vehicle Control ECU

Click Connector(A59)Engine Compartment>Engine Room Main Wire>Inverter Water Pump Assembly (with Motor)

A68-32 (NIWP) - A59-2 (NWP) Ignition switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(A68,A59)Location & Routing

Click Connector(A68)Instrument Panel>Engine Room Main Wire>Hybrid Vehicle Control ECU

Click Connector(A59)Engine Compartment>Engine Room Main Wire>Inverter Water Pump Assembly (with Motor)

A68-32 (NIWP) or A59-2 (NWP) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A59 inverter water pump assembly connector.


b.

Reconnect the A68 hybrid vehicle control ECU connector.



OK

6.CHECK HYBRID VEHICLE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HYBRID VEHICLE CONTROL ECU

Pre-procedure1

a.

Disconnect the A59 inverter water pump assembly connector.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

A458550C14
2.479,0.229 2.969,0.531 0.49,0.302 4.615,0.219 5.104,0.521 0.49,0.302 2.115,2.271 2.396,1.521 true 5.813,2.281 5.563,1.385 true 0.271,0.167 0.583,0.323 0.313,0.156 10 false *a 1.875,2.302 2.26,2.49 0.385,0.188 10 false NIWP 5.823,2.302 6.135,2.458 0.313,0.156 10 false E1 4.75,0.313 5.063,0.469 0.313,0.156 10 false H44 2.625,0.313 2.938,0.469 0.313,0.156 10 false A68
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A68,H44)Location & Routing

Click Connector(A68)Instrument Panel>Engine Room Main Wire>Hybrid Vehicle Control ECU

Click Connector(H44)Instrument Panel>Instrument Panel Wire / Speaker Wire>Hybrid Vehicle Control ECU

A68-32 (NIWP) - H44-15 (E1) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the A59 inverter water pump assembly connector.



OK

7.CLEAR DTC

NG

7.CLEAR DTC

NEXT

8.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE INVERTER WATER PUMP)
8.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE INVERTER WATER PUMP)
NOTICE:

Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.


HINT:

When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.


Pre-procedure1

a.

Perform the "Activate the Inverter Water Pump" Active Test.

Powertrain > Hybrid Control > Active Test
Tester Display
Activate the Inverter Water Pump
50004 397 1

Procedure1

a.

Connect an oscilloscope between the hybrid vehicle control ECU terminals specified in the table below, and measure the waveform.

A459997C01
2.51,0.302 2.969,0.604 0.458,0.302 4.635,0.302 5.094,0.604 0.458,0.302 1.865,2.563 2.313,1.604 true 5.948,2.563 5.479,1.49 true 4.552,3.698 5.01,3.896 0.458,0.198 10 false GND 1.573,2.604 2.031,2.802 0.458,0.198 10 false NIWP 5.958,2.604 6.417,2.802 0.458,0.198 10 false E1 4.76,0.385 5.219,0.583 0.458,0.198 10 false H44 2.635,0.385 3.094,0.583 0.458,0.198 10 false A68 0.573,0.25 1.031,0.448 0.458,0.198 10 false *a
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


Item Content
Terminal A68-32 (NIWP) - H44-15 (E1)
Equipment Setting 5 V/DIV., 5 ms./DIV.
Condition Ignition switch ON, during Active Test

OK:

The period of the wavelength is 13 msec. or less.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.



OK

NG

12.REPLACE INVERTER WATER PUMP ASSEMBLY
9.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

OK

10.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - IGCT RELAY)

NG

14.CHECK FUSE (INV W/P)
10.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - IGCT RELAY)

Pre-procedure1

a.

Remove the IGCT relay from the No. 5 relay block assembly.


b.

Disconnect the A59 inverter water pump assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A459998C01
1.604,0.771 2.031,1.042 0.427,0.271 2.25,2.083 2.104,1.635 true 3.604,0.167 3.917,0.323 0.313,0.156 10 false *1 3.719,1.938 4.031,2.094 0.313,0.156 10 false *2 0.354,0.177 0.667,0.333 0.313,0.156 10 false *a 2.094,2.125 2.708,2.323 0.615,0.198 10 false +BWP 1.719,0.833 2.333,1.031 0.615,0.198 10 false A59
*1 No. 5 Relay Block Assembly *2 IGCT Relay Holder
*a Front view of wire harness connector
(to Inverter Water Pump Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A59)Location & Routing

Click Connector(A59)Engine Compartment>Engine Room Main Wire>Inverter Water Pump Assembly (with Motor)

A59-4 (+BWP) - 5 (IGCT relay holder) Ignition switch off Below 1 Ω


NOTICE:

Do not apply excessive force when using the probes of the tester to perform the inspection. If excessive force is used, the terminals will be damaged.


HINT:
A288054C07
0.177,0.177 0.49,0.375 0.313,0.198 10 *a 0.99,1.385 1.302,1.583 0.313,0.198 10 *b 2.021,2.979 2.333,3.177 0.313,0.198 10 *c
*a Example
*b Shake Slightly
*c Vibrate Slightly


·

Connectors

Slightly shake the connector vertically and horizontally.

·

Wire Harness

Slightly shake the wire harness vertically and horizontally.

The connector joint and fulcrum of the vibration are the major areas that should be checked thoroughly.

·

No. 5 Relay Block Assembly

Apply slight vibration with a finger to the No. 5 relay block assembly and check whether a malfunction occurs.

·

INV W/P fuse

Apply slight vibration with a finger to the INV W/P fuse and check whether a malfunction occurs.

·

IGCT relay

Apply slight vibration with a finger to the IGCT relay and check whether a malfunction occurs.



Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A59 inverter water pump assembly connector.


b.

Install the IGCT relay.



OK

11.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - BODY GROUND)

NG

15.CHECK INSTALLATION CONDITION (INV W/P FUSE)
11.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - BODY GROUND)

Pre-procedure1

a.

Disconnect the A59 inverter water pump assembly connector.


Procedure1

a.
A425328C06
1.49,0.802 1.917,1.083 0.427,0.281 1.083,2.333 1.333,1.823 true 0.25,0.177 0.563,0.333 0.313,0.156 10 false *a 0.948,2.385 1.406,2.583 0.458,0.198 10 false GND 1.594,0.844 2.052,1.042 0.458,0.198 10 false A59
*a Front view of wire harness connector
(to Inverter Water Pump Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A59)Location & Routing

Click Connector(A59)Engine Compartment>Engine Room Main Wire>Inverter Water Pump Assembly (with Motor)

A59-1 (GND) - Body ground Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A59 inverter water pump assembly connector.



OK

12.REPLACE INVERTER WATER PUMP ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.REPLACE INVERTER WATER PUMP ASSEMBLY

NEXT

13.ADD HV COOLANT AND PERFORM AIR BLEEDING
13.ADD HV COOLANT AND PERFORM AIR BLEEDING
a.

After replacing the inverter water pump assembly, add HV coolant and perform air bleeding.

HINT:

Click hereGeneral>MAINTENANCE>COOLANT (for Inverter)>REPLACEMENT



Result:
Proceed to
NEXT



NEXT

END

14.CHECK FUSE (INV W/P)

Pre-procedure1

a.
A458558C01
0.885,1 1.333,0.438 true 0.219,0.156 0.531,0.313 0.313,0.156 10 false *1 0.719,0.979 1.031,1.135 0.313,0.156 10 false *2
*1 No. 5 Relay Block Assembly
*2 INV W/P Fuse


Remove the INV W/P fuse from the No. 5 relay block assembly.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
INV W/P fuse Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the INV W/P fuse.



OK

CONNECT SECURELY (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

NG

18.CONNECT SECURELY
15.CHECK INSTALLATION CONDITION (INV W/P FUSE)
a.

Check installation condition of the INV W/P fuse.

OK:

INV W/P fuse is installed correctly.



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY CIRCUIT)

NG

19.CHECK FUSE HOLDER TERMINAL (INV W/P FUSE)
16.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY CIRCUIT)

Pre-procedure1

a.

Remove the INV W/P fuse from the No. 5 relay block assembly.


b.

Remove the IGCT relay from the No. 5 relay block assembly.


c.

Disconnect the A59 inverter water pump assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A459999C01
1.76,0.771 2.229,1.052 0.469,0.281 2.521,2.083 2.313,1.583 true 3.583,0.177 3.896,0.333 0.313,0.156 10 false *1 4.563,0.677 4.875,0.833 0.313,0.156 10 false *2 3.906,2 4.219,2.156 0.313,0.156 10 false *3 0.521,0.167 0.833,0.323 0.313,0.156 10 false *a 1.896,0.844 2.375,1.083 0.479,0.24 10 false A59 2.406,2.125 2.885,2.365 0.479,0.24 10 false +BWP
*1 No. 5 Relay Block Assembly *2 INV W/P Fuse Holder
*3 IGCT Relay Holder - -
*a Front view of wire harness connector
(to Inverter Water Pump Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A59)Location & Routing

Click Connector(A59)Engine Compartment>Engine Room Main Wire>Inverter Water Pump Assembly (with Motor)

2 (INV W/P fuse holder) - A59-4 (+BWP) Ignition switch off Below 1 Ω
1 (INV W/P fuse holder) - 5 (IGCT relay) Ignition switch off Below 1 Ω
2 (INV W/P fuse holder) or A59-4 (+BWP) - Body ground and other terminals Ignition switch off 10 kΩ or higher


NOTICE:

Do not apply excessive force when using the probes of the tester to perform the inspection. If excessive force is used, the terminals will be damaged.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A59 inverter water pump assembly connector.


b.

Install the IGCT relay.


c.

Install the INV W/P fuse.



OK

17.CHECK FUSE (INV W/P)

NG

21.CHECK FUSE (INV W/P)
17.CHECK FUSE (INV W/P)

Pre-procedure1

a.
A458558C01
0.885,1 1.333,0.438 true 0.219,0.156 0.531,0.313 0.313,0.156 10 false *1 0.719,0.979 1.031,1.135 0.313,0.156 10 false *2
*1 No. 5 Relay Block Assembly
*2 INV W/P Fuse


Remove the INV W/P fuse from the No. 5 relay block assembly.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
INV W/P fuse Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the INV W/P fuse.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/P FUSE HOLDER TERMINAL)

NG

22.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - BODY GROUND)
18.CONNECT SECURELY
a.

Connect the inverter water pump assembly connector securely.


Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (INV W/P)

19.CHECK FUSE HOLDER TERMINAL (INV W/P FUSE)
a.

Check the terminals of the INV W/P fuse holder.

OK:

The terminals of the INV W/P fuse holder are not bent, loose or corroded.



Result:
Proceed to
OK
NG



OK

20.CHECK FUSE (INV W/P)

NG

26.CHECK FUSE (INV W/P)
20.CHECK FUSE (INV W/P)

Pre-procedure1

a.
A458558C01
0.885,1 1.333,0.438 true 0.219,0.156 0.531,0.313 0.313,0.156 10 false *1 0.719,0.979 1.031,1.135 0.313,0.156 10 false *2
*1 No. 5 Relay Block Assembly
*2 INV W/P Fuse


Remove the INV W/P fuse from the No. 5 relay block assembly.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
INV W/P fuse Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the INV W/P fuse.



OK

CONNECT SECURELY (INV W/P FUSE)

NG

REPLACE FUSE (INV W/P)

21.CHECK FUSE (INV W/P)

Pre-procedure1

a.
A458558C01
0.885,1 1.333,0.438 true 0.219,0.156 0.531,0.313 0.313,0.156 10 false *1 0.719,0.979 1.031,1.135 0.313,0.156 10 false *2
*1 No. 5 Relay Block Assembly
*2 INV W/P Fuse


Remove the INV W/P fuse from the No. 5 relay block assembly.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
INV W/P fuse Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the INV W/P fuse.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

27.REPAIR OR REPLACE HARNESS OR CONNECTOR
22.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - BODY GROUND)

Pre-procedure1

a.

Disconnect the A59 inverter water pump assembly connector.


Procedure1

a.
A425328C06
1.49,0.802 1.917,1.083 0.427,0.281 1.083,2.333 1.333,1.823 true 0.25,0.177 0.563,0.333 0.313,0.156 10 false *a 0.948,2.385 1.406,2.583 0.458,0.198 10 false GND 1.594,0.844 2.052,1.042 0.458,0.198 10 false A59
*a Front view of wire harness connector
(to Inverter Water Pump Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A59)Location & Routing

Click Connector(A59)Engine Compartment>Engine Room Main Wire>Inverter Water Pump Assembly (with Motor)

A59-1 (GND) - Body ground Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A59 inverter water pump assembly connector.



OK

23.CHECK FUSE HOLDER TERMINAL (INV W/P FUSE)

NG

27.REPAIR OR REPLACE HARNESS OR CONNECTOR
23.CHECK FUSE HOLDER TERMINAL (INV W/P FUSE)
a.

Check the terminals of the INV W/P fuse holder.

OK:

The terminals of the INV W/P fuse holder are not bent, loose or corroded.



Result:
Proceed to
OK
NG



OK

24.REPLACE INVERTER WATER PUMP ASSEMBLY

NG

28.REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/P FUSE HOLDER TERMINAL)
24.REPLACE INVERTER WATER PUMP ASSEMBLY

NEXT

25.ADD HV COOLANT AND PERFORM AIR BLEEDING
25.ADD HV COOLANT AND PERFORM AIR BLEEDING
a.

After replacing the inverter water pump assembly, add HV coolant and perform air bleeding.

HINT:

Click hereGeneral>MAINTENANCE>COOLANT (for Inverter)>REPLACEMENT



Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (INV W/P)

26.CHECK FUSE (INV W/P)

Pre-procedure1

a.
A458558C01
0.885,1 1.333,0.438 true 0.219,0.156 0.531,0.313 0.313,0.156 10 false *1 0.719,0.979 1.031,1.135 0.313,0.156 10 false *2
*1 No. 5 Relay Block Assembly
*2 INV W/P Fuse


Remove the INV W/P fuse from the No. 5 relay block assembly.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
INV W/P fuse Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the INV W/P fuse.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/P FUSE HOLDER TERMINAL)

NG

28.REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/P FUSE HOLDER TERMINAL)
27.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (INV W/P)

28.REPAIR OR REPLACE HARNESS OR CONNECTOR (INV W/P FUSE HOLDER TERMINAL)
a.

Repair or replace the terminals of the INV W/P fuse holder.


Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (INV W/P)