Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441183 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0AA000  Hybrid/EV Battery Positive Contactor Circuit Stuck Closed  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The hybrid vehicle control ECU detects a stuck closed malfunction of a system main relay on the HV battery positive (+) terminal side.

The cause of this malfunction may be one of the following:

Inverter voltage sensor (VH) internal circuit malfunction
·

Voltage sensor (VH) malfunction

·

Motor generator control ECU (MG ECU) malfunction

·

Communication (wire harness) malfunction


High voltage system malfunction
·

No. 1 traction battery device box assembly malfunction


Low-voltage circuit (12 V) malfunction
·

Hybrid vehicle control ECU malfunction

·

No. 1 traction battery device box assembly malfunction

·

Low voltage wire harness malfunction

·

Low voltage connector malfunction



DESCRIPTION

Refer to the description for DTC P0AE411.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE411

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
P0AA000 Hybrid/EV Battery Positive Contactor Circuit Stuck Closed Even the system main relay of HV battery positive (+) terminal side is turned off, the inverter voltage (VH) does not drop.
(1 trip detection logic)
·

No. 1 traction battery device box assembly

·

Hybrid motor control inverter assembly

·

Hybrid vehicle control ECU

·

Wire harness or connector


Does not come on Master Warning: Comes on Hybrid Control A

Related Data List
DTC No. Data List
P0AA000
·

Hybrid/EV Battery Voltage

·

VH-Voltage after Boosting

·

VL-Voltage before Boosting



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON (READY) and wait for 3 minutes or more.

HINT:

According to the display on the GTS, read the Data List and monitor the values of "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" for 3 minutes. If the difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" is always less than 50 V, the vehicle has returned to normal.


4.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for the HV Battery High-voltage Line Circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>HV Battery High-voltage Line Circuit

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*

*: for AWD

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C58
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*.


*: for AWD

·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

If the DTCs are cleared or the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal before performing repairs, turning the ignition switch to ON (READY) may cause a malfunction. Do not turn the ignition switch to ON (READY).



HINT:

If DTC P0AA000 is output, the ignition switch cannot be turned to ON (READY).


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL, MOTOR GENERATOR)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > Motor Generator > Trouble Codes
50001 395
Result:
Result Proceed to
Only P0AA000 for Hybrid Control System is output A
P0AA000 and DTCs other than the DTCs in the table below are output B
P0AA000 and Microcomputer malfunction of Hybrid Control System DTCs in the table below are output C
P0AA000 and Microcomputer malfunction of Motor generator control system DTCs in the table below are output D
P0AA000 and Power source circuit malfunction of Motor generator control system DTCs in the table below are output E
P0AA000 and Communication system malfunction of Hybrid Control System DTCs in the table below are output F
P0AA000 and Sensor and actuator circuit malfunction of Hybrid Control System DTCs in the table below are output G
P0AA000 and Sensor and actuator circuit malfunction of Motor generator control system DTCs in the table below are output H
P0AA000 and System malfunction of Hybrid Control System DTCs in the table below are output I
P0AA000 and System malfunction of Motor generator control system DTCs in the table below are output J


Table 1
System Relevant DTC
Hybrid Control System P0AA000 Hybrid/EV Battery Positive Contactor Circuit Stuck Closed

Table 2
Malfunction Content System Relevant DTC
Microcomputer malfunction Hybrid control system P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P060687 Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message
P0A1B49 Drive Motor "A" Control Module Internal Electronic Failure
P1C9E9F Hybrid/EV System Reset Stuck Off
Motor generator control system P0A1B1F Generator Control Module Circuit Intermittent
P0A1A47 Generator Control Module Watchdog / Safety MC Failure
P0A1A49 Generator Control Module Internal Electronic Failure
P1C2A1C Generator A/D Converter Circuit Circuit Voltage Out of Range
P1C2A49 Generator A/D Converter Circuit Internal Electronic Failure
P1C2B1C Drive Motor "A" Control Module A/D Converter Circuit Voltage Out of Range
P1C2B49 Drive Motor "A" Control Module A/D Converter Circuit Internal Electronic Failure
P1CAC49 Generator Position Sensor Internal Electronic Failure
P1CAD49 Drive Motor "A" Position Sensor Internal Electronic Failure
P1CAF38 Generator Position Sensor REF Signal Cycle Malfunction Signal Frequency Incorrect
P1CB038 Drive Motor "A" Position Sensor REF Signal Frequency Incorrect
P313383 Communication Error from Generator to Drive Motor "A" Value of Signal Protection Calculation Incorrect
P313386 Communication Error from Generator to Drive Motor "A" Signal Invalid
P313387 Communication Error from Generator to Drive Motor "A" Missing Message
Power source circuit malfunction Motor generator control system P06D61C Generator Control Module Offset Power Circuit Voltage Out of Range
P06B01C Generator Control Module Position Sensor REF Power Source Circuit Voltage Out of Range
Communication system malfunction Hybrid control system P312387 Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message
Sensor and actuator circuit malfunction Hybrid control system P0AD911 Hybrid/EV Battery Positive Contactor Circuit Short to Ground
P0AD915 Hybrid/EV Battery Positive Contactor Circuit Short to Auxiliary Battery or Open
P0ADD11 Hybrid/EV Battery Negative Contactor Circuit Short to Ground
P0ADD15 Hybrid/EV Battery Negative Contactor Circuit Short to Auxiliary Battery or Open
P0AE411 Hybrid/EV Battery Precharge Contactor Circuit Short to Ground
P0AE415 Hybrid/EV Battery Precharge Contactor Circuit Short to Auxiliary Battery or Open
Motor generator control system P0A3F16 Drive Motor "A" Position Sensor Circuit Voltage Below Threshold
P0A4B16 Generator Position Sensor Circuit Voltage Below Threshold
P0A4B21 Generator Position Sensor Signal Amplitude < Minimum
P0A4B22 Generator Position Sensor Signal Amplitude > Maximum
P0C5013 Drive Motor "A" Position Sensor Circuit "A" Circuit Open
P0C5016 Drive Motor "A" Position Sensor Circuit "A" Circuit Voltage Below Threshold
P0C5017 Drive Motor "A" Position Sensor Circuit "A" Circuit Voltage Above Threshold
P0C5A13 Drive Motor "A" Position Sensor Circuit "B" Circuit Open
P0C5A16 Drive Motor "A" Position Sensor Circuit "B" Circuit Voltage Below Threshold
P0C5A17 Drive Motor "A" Position Sensor Circuit "B" Circuit Voltage Above Threshold
P0C6413 Generator Position Sensor Circuit "A" Circuit Open
P0C6416 Generator Position Sensor Circuit "A" Circuit Voltage Below Threshold
P0C6417 Generator Position Sensor Circuit "A" Circuit Voltage Above Threshold
P0C6913 Generator Position Sensor Circuit "B" Circuit Open
P0C6916 Generator Position Sensor Circuit "B" Circuit Voltage Below Threshold
P0C6917 Generator Position Sensor Circuit "B" Circuit Voltage Above Threshold
System malfunction Hybrid control system P0D2D1C Drive Motor "A" Inverter Voltage Sensor Voltage Out of Range
P1C8349 High Voltage Power Resource Circuit Voltage Sensor after Boosting Malfunction
P0C7600 Hybrid/EV Battery System Discharge Time Too Long
Motor generator control system P0D2D16 Drive Motor "A" Inverter Voltage Sensor (VH) Circuit Voltage Below Threshold
P0D2D17 Drive Motor "A" Inverter Voltage Sensor (VH) Circuit Voltage Above Threshold
P1CB69E Drive Motor "A" Inverter Voltage Sensor (VH) Stuck On

HINT:
·

P0AA000 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

B

2.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

C

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

D

E

F

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

G

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

H

I

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

J

2.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

Pre-procedure1

a.

None.


Procedure1

a.

Read the freeze frame data of DTC P0AA000.

Powertrain > Hybrid Control > DTC(P0AA000) > Freeze Frame Data
Tester Display
VL-Voltage before Boosting
VH-Voltage after Boosting
50040 397 150,151 P0AA000
NOTICE:

As freeze frame data is stored immediately before and after a DTC is stored, make sure to only read the values for the moment the DTC was stored ("0(s)").


Result:
Result Proceed to
Difference between "VL-Voltage before Boosting" and "VH-Voltage after Boosting" is less than 56 V. A
Difference between "VL-Voltage before Boosting" and "VH-Voltage after Boosting" is 56 V or more. B


HINT:

If VH-Voltage after Boosting is output even when an off command is being sent to the system main relay (positive side), P0AA000 is output. If the difference between the "VL-Voltage before Boosting" and the "VH-Voltage after Boosting" is large, it is determined that there is an inverter (VH sensor) malfunction.



Post-procedure1

a.

Turn the ignition switch off.



A

3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

B

REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

5.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)

NG

4.CONNECT SECURELY
4.CONNECT SECURELY
Result:
Proceed to
NEXT



NEXT

5.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)
5.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)
a.
A475644N01
2.438,0.677 2.813,0.938 0.375,0.26 2.5,0.729 2.792,0.896 0.292,0.167 10 true OH3

Check the connection condition of the OH3 floor wire connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

8.CHECK CONNECTOR CONNECTION CONDITION (NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY CONNECTOR)

B

6.CONNECT SECURELY

C

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CONNECT SECURELY
Result:
Proceed to
NEXT



NEXT

8.CHECK CONNECTOR CONNECTION CONDITION (NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY CONNECTOR)
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

8.CHECK CONNECTOR CONNECTION CONDITION (NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY CONNECTOR)
8.CHECK CONNECTOR CONNECTION CONDITION (NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY CONNECTOR)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



Procedure1

a.
A458484N01
0.719,0.292 1.104,0.563 0.385,0.271 0.792,0.344 1.073,0.51 0.281,0.167 10 true O70

Check the connector connections and contact pressure of the relevant terminals of the O70 No. 1 traction battery device box assembly connector.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

The connectors are connected securely and there are no contact pressure problems.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the HV battery upper cover panel.



OK

10.CHECK GROUND WIRE CONNECTION CONDITION (SMR ACTIVATION LOW-VOLTAGE CIRCUIT)

NG

9.CONNECT SECURELY
9.CONNECT SECURELY
Result:
Proceed to
NEXT



NEXT

10.CHECK GROUND WIRE CONNECTION CONDITION (SMR ACTIVATION LOW-VOLTAGE CIRCUIT)
10.CHECK GROUND WIRE CONNECTION CONDITION (SMR ACTIVATION LOW-VOLTAGE CIRCUIT)
a.

Check the installation condition of the ground wire OB.

OK:

The ground wire OB is securely installed.



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY)

NG

11.CONNECT SECURELY
11.CONNECT SECURELY
Result:
Proceed to
NEXT



NEXT

12.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY)
12.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.

Disconnect the O70 No. 1 traction battery device box assembly connector.


d.

Disconnect the H44 hybrid vehicle control ECU connector.


Procedure1

a.
A458549C01
1.531,2.573 1.979,2.896 0.448,0.323 1.448,0.156 1.917,0.427 0.469,0.271 1.417,3.583 1.052,4.135 true 0.885,1.188 1.406,1.99 true 0.094,0.125 0.406,0.281 0.313,0.156 10 false *a 0.167,2.469 0.479,2.625 0.313,0.156 10 false *b 1.573,0.229 1.906,0.406 0.333,0.177 10 false H44 1.635,2.656 1.969,2.833 0.333,0.177 10 false O70 1.406,2.01 2.021,2.208 0.615,0.198 10 false SMRB 0.729,4.156 1.344,4.354 0.615,0.198 10 false SMRB
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to No. 1 Traction Battery Device Box Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition

Click Location & Routing(H44,O70)Location & Routing

Click Connector(H44)Instrument Panel>Instrument Panel Wire / Speaker Wire>Hybrid Vehicle Control ECU

Click Connector(O70)Body>Floor Wire>HV Battery Junction Block Assembly

H44-2 (SMRB) - O70-1 (SMRB) Ignition switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(H44,O70)Location & Routing

Click Connector(H44)Instrument Panel>Instrument Panel Wire / Speaker Wire>Hybrid Vehicle Control ECU

Click Connector(O70)Body>Floor Wire>HV Battery Junction Block Assembly

H44-2 (SMRB) or O70-1 (SMRB) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the H44 hybrid vehicle control ECU connector.


b.

Reconnect the O70 No. 1 traction battery device box assembly connector.


c.

Install the HV battery upper cover panel.



OK

14.CHECK HARNESS AND CONNECTOR (NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY - BODY GROUND)

NG

13.REPAIR OR REPLACE HARNESS OR CONNECTOR
13.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

14.CHECK HARNESS AND CONNECTOR (NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY - BODY GROUND)
14.CHECK HARNESS AND CONNECTOR (NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.

Disconnect the O70 No. 1 traction battery device box assembly connector.


Procedure1

a.
A436194C15
1.5,0.271 1.906,0.573 0.406,0.302 1.823,1.229 2.292,1.823 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 2.354,1.74 2.667,1.896 0.313,0.156 10 false GND 1.594,0.365 1.948,0.604 0.354,0.24 10 false O70
*a Front view of wire harness connector
(to No. 1 Traction Battery Device Box Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O70)Location & Routing

Click Connector(O70)Body>Floor Wire>HV Battery Junction Block Assembly

O70-3 (GND) - Body ground Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the O70 No. 1 traction battery device box assembly connector.


b.

Install the HV battery upper cover panel.



OK

16.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRB)

NG

15.REPAIR OR REPLACE HARNESS OR CONNECTOR
15.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

16.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRB)
16.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRB)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.

Disconnect the O70 No. 1 traction battery device box assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A458079C14
3.823,1.073 4.208,1.344 0.385,0.271 3.229,1.438 3.417,1.26 true 3.771,1.438 3.604,1.26 true 0.573,0.146 0.885,0.302 0.313,0.156 10 false *a 3.01,1.469 3.344,1.677 0.333,0.208 10 true GND 3.74,1.458 4.219,1.667 0.479,0.208 10 true SMRB 3.906,1.135 4.219,1.323 0.313,0.188 10 false O70
*a Component without harness connected
(No. 1 Traction Battery Device Box Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O70)Location & Routing

Click Connector(O70)Body>Floor Wire>HV Battery Junction Block Assembly

O70-1 (SMRB) - O70-3 (GND) -40 to 80°C (-40 to 176°F) 19.0 to 59.0 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the O70 No. 1 traction battery device box assembly connector.


b.

Install the HV battery upper cover panel.



OK

17.CHECK VEHICLE CONDITION

NG

24.REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY
17.CHECK VEHICLE CONDITION
a.

Choose the model to be inspected.


Result:
Result Proceed to
for 2WD A
for AWD B



A

18.CHECK NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRB)

B

23.CHECK NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRB)
18.CHECK NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRB)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
A458485N01
1.896,1.875 2.26,2.104 0.365,0.229 2.896,0.073 3.26,0.302 0.365,0.229 2.49,1.563 2.896,1.813 0.406,0.25 2.792,1.104 3.167,1.354 0.375,0.25 1.969,1.917 2.219,2.083 0.25,0.167 10 true z10 2.99,0.115 3.198,0.281 0.208,0.167 10 true z9 2.573,1.594 2.823,1.792 0.25,0.198 10 true a1 2.865,1.156 3.135,1.323 0.271,0.167 10 true a2

Disconnect the 2 HV floor under wire connectors from the No. 1 traction battery device box assembly.


d.

Disconnect the 2 HV battery high voltage connectors from the No. 1 traction battery device box assembly.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



Procedure1

a.
A458486C03
1.333,1.844 1.688,2.073 0.354,0.229 1.729,1.26 2.083,1.49 0.354,0.229 1.542,0.792 1.906,1.031 true 1.052,1.771 0.792,1.552 true 0.083,0.052 0.313,0.24 0.229,0.188 10 true *a 1.281,0.688 1.552,0.854 0.271,0.167 10 true CBI 0.594,1.438 0.75,1.604 0.156,0.167 10 true + 1.844,1.313 2.01,1.458 0.167,0.146 10 true a1 1.406,1.896 1.656,2.052 0.25,0.156 10 true z10
*a Component without harness connected
(No. 1 Traction Battery Device Box Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(a1,z10)Location & Routing

Click Connector(a1)Body>HV Floor Under Wire>HV Battery Junction Block Assembly

Click Connector(z10)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assembly

a1-1 (CBI) - z10-1 (+) Ignition switch off 10 kΩ or higher


HINT:
·

If a system main relay is stuck closed, inspect the No. 1 traction battery device box assembly without removing it from the vehicle, in order to keep the relay closed.

·

If the result of reading the freeze frame data is A, the No. 1 traction battery device box assembly must be replaced. Measuring resistance can determine that this is either a present or past malfunction.

·

If the check result is OK and the past malfunction is NG, then the malfunction can be judged as a present malfunction.



Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the 2 HV battery high voltage connectors.


b.

Reconnect the 2 HV floor under wire connectors.


c.

Install the HV battery upper cover panel.



OK

19.REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

NG

20.REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY
19.REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

NEXT

22.CHECK HYBRID VEHICLE CONTROL ECU (CHECK FOR NORMAL OPERATION)
20.REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

NEXT

21.CLEAR DTC
21.CLEAR DTC
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Install the service plug grip.


Procedure1

a.

Clear the DTCs.

Powertrain > Hybrid Control > Clear DTCs
50002 397
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for 2 minutes or more.



NEXT

22.CHECK HYBRID VEHICLE CONTROL ECU (CHECK FOR NORMAL OPERATION)
22.CHECK HYBRID VEHICLE CONTROL ECU (CHECK FOR NORMAL OPERATION)

Pre-procedure1

a.

Turn the ignition switch to ON (READY).


Procedure1

a.

According to the display on the GTS, read the Data List and monitor the values of "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" for 3 minutes.

Powertrain > Hybrid Control > Data List
Tester Display
VL-Voltage before Boosting
Hybrid/EV Battery Voltage
50003 397 150,227
Result:
Result Proceed to
Difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" is always less than 50 V. A
Difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" is 50 V or more. B



Post-procedure1

a.

Turn the ignition switch off.



A

END

B

REPLACE HYBRID VEHICLE CONTROL ECU AND NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

23.CHECK NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRB)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
A458485N02
1.896,1.875 2.26,2.104 0.365,0.229 2.49,1.542 2.813,1.75 0.323,0.208 2.896,0.073 3.26,0.302 0.365,0.229 2.802,1.26 3.115,1.49 0.313,0.229 1.969,1.917 2.219,2.083 0.25,0.167 10 true z10 2.573,1.573 2.771,1.719 0.198,0.146 10 true c1 2.99,0.115 3.198,0.281 0.208,0.167 10 true z9 2.896,1.302 3.063,1.469 0.167,0.167 10 true c2

Disconnect the 2 HV floor under wire connectors from the No. 1 traction battery device box assembly.


d.

Disconnect the 2 HV battery high voltage connectors from the No. 1 traction battery device box assembly.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



Procedure1

a.
A458486C05
1.333,1.844 1.688,2.073 0.354,0.229 1.729,1.26 2.083,1.49 0.354,0.229 1.542,0.792 1.906,1.031 true 1.052,1.771 0.792,1.552 true 0.083,0.052 0.313,0.24 0.229,0.188 10 true *a 1.281,0.688 1.552,0.854 0.271,0.167 10 true CBI 0.594,1.438 0.75,1.604 0.156,0.167 10 true + 1.844,1.302 2.021,1.458 0.177,0.156 10 true c1 1.406,1.885 1.656,2.021 0.25,0.135 10 true z10
*a Component without harness connected
(No. 1 Traction Battery Device Box Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(c1,z10)Location & Routing

Click Connector(c1)Body>HV Battey Pack Wire>HV Battery Junction Block Assembly

Click Connector(z10)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assembly

c1-1 (CBI) - z10-1 (+) Ignition switch off 10 kΩ or higher


HINT:
·

If a system main relay is stuck closed, inspect the No. 1 traction battery device box assembly without removing it from the vehicle, in order to keep the relay closed.

·

If the result of reading the freeze frame data is A, the No. 1 traction battery device box assembly must be replaced. Measuring resistance can determine that this is either a present or past malfunction.

·

If the check result is OK and the past malfunction is NG, then the malfunction can be judged as a present malfunction.



Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the 2 HV battery high voltage connectors.


b.

Reconnect the 2 HV floor under wire connectors.


c.

Install the HV battery upper cover panel.



OK

19.REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

NG

20.REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY
24.REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

NEXT

22.CHECK HYBRID VEHICLE CONTROL ECU (CHECK FOR NORMAL OPERATION)