Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441183 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  HV Battery High-voltage Line Circuit  


DESCRIPTION

The cause of the malfunction may be the HV battery high-voltage line circuit.

Check the continuity in the high-voltage line from the HV battery to the inverter.

Check the connection condition and for an open circuit in the frame wire from the service plug grip, EV electric battery fuse and HV battery to the inverter and perform a function check of the system main relay.

Related Parts Check
Area Inspection
High-voltage circuit from HV battery to inverter Check connection condition and for open circuit.
Service plug grip Check connection condition and for open circuit.
EV electric battery fuse Check for open circuit.
System Main Relay Check operation condition as relay.

SYSTEM DESCRIPTION

The HV battery high voltage is supplied to the inverter via the system main relay operation.

WIRING DIAGRAM

A459740E07
0.292,3.24 1.083,3.781 0.792,0.542 10 false Service Plug Grip 1.719,0.708 2.094,0.896 0.375,0.188 10 false z10 1.792,0.531 1.948,0.729 0.156,0.198 10 false 1 1.188,1.438 1.344,1.635 0.156,0.198 10 false 1 1.177,2.208 1.333,2.406 0.156,0.198 10 false 1 1.229,3.26 1.385,3.458 0.156,0.198 10 false 1 1.385,2.208 1.844,2.406 0.458,0.198 10 false z14 1.417,2.906 1.875,3.104 0.458,0.198 10 false z8 1.229,3.656 1.385,3.854 0.156,0.198 10 false 2 0.125,2.438 1.052,3.177 0.927,0.74 10 false Hybrid Battery Terminal Block 0.156,0.615 1.229,1.542 1.073,0.927 10 false No. 2 HV Supply Stack Sub-assembly 0.156,1.521 1.104,2.448 0.948,0.927 10 false No. 1 HV Supply Stack Sub-assembly 1.729,3.667 2.188,3.865 0.458,0.198 10 false z9 1.813,3.458 1.969,3.656 0.156,0.198 10 false 1 2.063,0.552 2.219,0.75 0.156,0.198 10 false + 2.073,3.49 2.229,3.688 0.156,0.198 10 false - 3.042,1.406 3.656,1.604 0.615,0.198 10 false SMRB 3.031,4.333 3.667,4.542 0.635,0.208 10 false SMRG 3.042,5.76 3.677,5.969 0.635,0.208 10 false SMRP 4.052,1.042 4.667,1.24 0.615,0.198 10 false SMRB 6.219,4.479 6.833,4.677 0.615,0.198 10 false SMRB 6.198,4.948 6.833,5.156 0.635,0.208 10 false SMRG 6.208,5.417 6.844,5.625 0.635,0.208 10 false SMRP 4.042,5.396 4.677,5.604 0.635,0.208 10 false SMRP 4.063,4 4.698,4.208 0.635,0.208 10 false SMRG 4.25,0.563 4.708,0.76 0.458,0.198 10 false CBI 4.219,3.5 4.677,3.698 0.458,0.198 10 false CEI 4.146,5.885 4.604,6.083 0.458,0.198 10 false GND 4.635,0.719 4.948,0.917 0.313,0.198 10 false a1 4.677,0.5 4.833,0.698 0.156,0.198 10 false 1 4.583,1.167 5.042,1.365 0.458,0.198 10 false O70 4.677,0.979 4.833,1.177 0.156,0.198 10 false 1 4.615,3.667 4.927,3.865 0.313,0.198 10 false a2 4.677,3.479 4.833,3.677 0.156,0.198 10 false 1 4.594,4.115 5.052,4.313 0.458,0.198 10 false O70 4.583,5.521 5.042,5.719 0.458,0.198 10 false O70 4.594,5.979 5.052,6.177 0.458,0.198 10 false O70 4.688,3.927 4.844,4.125 0.156,0.198 10 false 4 4.677,5.313 4.833,5.51 0.156,0.198 10 false 2 4.677,5.802 4.833,6 0.156,0.198 10 false 3 1.896,6.49 4.771,6.698 2.875,0.208 10 false No. 1 Traction Battery Device Box Assembly 6.042,6.438 6.354,6.635 0.313,0.198 10 false H44 6.042,6.615 6.958,6.99 0.917,0.375 10 false Hybrid Vehicle Control ECU 6.031,4.458 6.344,4.656 0.313,0.198 10 false 2 5.99,4.948 6.302,5.146 0.313,0.198 10 false 27 5.969,5.406 6.281,5.604 0.313,0.198 10 false 16 5.729,1.958 6.042,2.156 0.313,0.198 10 false a3 5.719,2.115 7.042,2.51 1.323,0.396 10 false Hybrid Motor Control Inverter Assembly 6.323,0.74 6.781,0.938 0.458,0.198 10 false CBI 6.313,1.604 6.771,1.802 0.458,0.198 10 false CEI 6.094,0.583 6.25,0.781 0.156,0.198 10 false 1 6.104,1.417 6.26,1.615 0.156,0.198 10 false 2 6.896,4.75 7.052,4.948 0.156,0.198 10 false * 6.885,5.198 7.042,5.396 0.156,0.198 10 false * 6.896,5.688 7.052,5.885 0.156,0.198 10 false * 1.24,7.354 2.927,7.854 1.688,0.5 10 false : HV Battery Voltage Line 3.292,7.333 6.813,7.531 3.521,0.198 10 false *: with Monitor Circuit 1.177,2.917 1.333,3.115 0.156,0.198 10 false 1 5.135,6.26 5.448,6.458 0.313,0.198 10 false OB 1.448,1.458 1.604,1.656 0.156,0.198 10 false A 0.104,0.094 1.708,0.448 1.604,0.354 12 false for 2WD:

A460288E03
0.104,0.073 1.333,0.271 1.229,0.198 12 false for AWD: 1.5,0.948 1.771,1.146 0.271,0.198 10 false z10 1.573,0.76 1.729,0.958 0.156,0.198 10 false 1 0.063,3.469 0.927,3.844 0.865,0.375 10 false Service Plug Grip 1.01,1.677 1.167,1.875 0.156,0.198 10 false 1 1.177,2.448 1.635,2.646 0.458,0.198 10 false z14 0.042,2.667 1.021,3.083 0.979,0.417 10 false Hybrid Battery Terminal Block 1.208,3.135 1.667,3.333 0.458,0.198 10 false z8 1,2.427 1.156,2.625 0.156,0.198 10 false 1 0.073,1.104 0.99,1.646 0.917,0.542 10 false No. 2 HV Supply Stack Sub-assembly 1.531,3.896 1.99,4.094 0.458,0.198 10 false z9 1.573,3.719 1.729,3.917 0.156,0.198 10 false 1 1.844,0.802 2,1 0.156,0.198 10 false + 1.844,3.75 2,3.948 0.156,0.198 10 false - 2.719,1.594 3.333,1.792 0.615,0.198 10 false SMRB 3.594,1.292 4.208,1.49 0.615,0.198 10 false SMRB 2.698,4.542 3.313,4.74 0.615,0.198 10 false SMRG 3.521,4.229 4.135,4.427 0.615,0.198 10 false SMRG 2.698,5.958 3.313,6.156 0.615,0.198 10 false SMRP 3.542,5.635 4.156,5.833 0.615,0.198 10 false SMRP 3.708,0.813 4.167,1.01 0.458,0.198 10 false CBI 3.729,3.74 4.188,3.938 0.458,0.198 10 false CEI 3.646,6.094 4.104,6.292 0.458,0.198 10 false GND 4.094,0.938 4.406,1.135 0.313,0.198 10 false c1 4.031,1.375 4.49,1.573 0.458,0.198 10 false O70 4.031,4.333 4.49,4.531 0.458,0.198 10 false O70 4.031,6.198 4.49,6.396 0.458,0.198 10 false O70 4.031,5.74 4.49,5.938 0.458,0.198 10 false O70 4.083,3.885 4.396,4.083 0.313,0.198 10 false c2 4.135,0.76 4.292,0.958 0.156,0.198 10 false 1 4.135,1.208 4.292,1.406 0.156,0.198 10 false 1 4.125,3.719 4.281,3.917 0.156,0.198 10 false 1 4.125,4.167 4.281,4.365 0.156,0.198 10 false 4 4.115,5.563 4.271,5.76 0.156,0.198 10 false 2 4.115,6.042 4.271,6.24 0.156,0.198 10 false 3 1.458,6.688 4.667,6.885 3.208,0.198 10 false No. 1 Traction Battery Device Box Assembly 4.698,0.927 5.01,1.125 0.313,0.198 10 false c6 4.698,1.792 5.01,1.99 0.313,0.198 10 false c6 4.74,0.75 4.896,0.948 0.156,0.198 10 false 1 4.729,1.615 4.885,1.813 0.156,0.198 10 false 2 4.99,0.938 5.604,1.135 0.615,0.198 10 false RCBI 4.979,1.792 5.594,1.99 0.615,0.198 10 false RCEI 5.448,0.927 6.063,1.125 0.615,0.198 10 false RCBO 5.448,1.781 6.063,1.979 0.615,0.198 10 false RCEO 5.979,0.927 6.292,1.125 0.313,0.198 10 false a4 5.979,1.781 6.292,1.979 0.313,0.198 10 false a4 6.01,0.76 6.167,0.958 0.156,0.198 10 false 2 6.01,1.615 6.167,1.813 0.156,0.198 10 false 1 6.427,0.927 6.885,1.125 0.458,0.198 10 false CBI 6.438,1.792 6.896,1.99 0.458,0.198 10 false CEI 6.271,1.656 6.427,1.854 0.156,0.198 10 false 2 6.271,0.823 6.427,1.021 0.156,0.198 10 false 1 6.125,2.313 6.438,2.51 0.313,0.198 10 false a3 6.146,2.469 7.094,2.99 0.948,0.521 10 false Hybrid Motor Control Inverter Assembly 4.927,2.302 5.99,2.969 1.063,0.667 10 false Hybrid Motor Control Inverter Assembly Rear 5.99,4.729 6.302,4.927 0.313,0.198 10 false 2 6.208,5.188 6.823,5.385 0.615,0.198 10 false SMRG 6.219,4.719 6.833,4.917 0.615,0.198 10 false SMRB 6.219,5.646 6.833,5.844 0.615,0.198 10 false SMRP 5.969,5.167 6.281,5.365 0.313,0.198 10 false 27 5.958,5.635 6.271,5.833 0.313,0.198 10 false 16 6.104,6.688 6.417,6.885 0.313,0.198 10 false H44 6.115,6.875 7.083,7.365 0.969,0.49 10 false Hybrid Vehicle Control ECU 1.229,7.375 2.844,7.615 1.615,0.24 10 false : HV Battery Voltage Line 2.938,7.365 4.906,7.542 1.969,0.177 10 false *: with Monitor Circuit 6.885,4.708 7.021,4.875 0.135,0.167 10 false * 6.885,5.208 7.063,5.385 0.177,0.177 10 false * 6.896,5.667 7.073,5.844 0.177,0.177 10 false * 0.083,1.885 1.01,2.427 0.927,0.542 10 false No. 1 HV Supply Stack Sub-assembly 1.24,1.688 1.396,1.885 0.156,0.198 10 false A 1,3.156 1.156,3.354 0.156,0.198 10 false 1 1.021,3.5 1.177,3.698 0.156,0.198 10 false 1 1.01,3.875 1.167,4.073 0.156,0.198 10 false 2 4.802,6.5 5.26,6.698 0.458,0.198 10 false OB

CAUTION / NOTICE / HINT

This diagnostic procedure is referenced to in the diagnostic procedure of several DTCs.

If the result of this diagnostic procedure is normal, proceed as directed in the procedure for the DTC.

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*

*: for AWD

-

Disconnecting the low voltage connector of the HV battery



·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.


·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.


·
A357589C58
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*.


*: for AWD



NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK HYBRID MOTOR CONTROL INVERTER ASSEMBLY (HV FLOOR UNDER WIRE CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



Procedure1

a.
A475642

Check that the bolts for the HV floor under wire is tightened to the specified torque, the HV floor under wire is connected securely, and there are no contact problems.

Specified Condition:

T = 8.0 N*m (82 kgf*cm, 71 in.*lbf)



b.

Disconnect the HV floor under wire from the hybrid motor control inverter assembly.


c.

Check for arc marks on the terminals for the HV floor under wire and hybrid motor control inverter assembly.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



Post-procedure1

a.

Reconnect the HV floor under wire.



A

2.CHECK VEHICLE CONDITION

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

2.CHECK VEHICLE CONDITION
a.

Choose the model to be inspected.


Result:
Result Proceed to
for 2WD A
for AWD B



A

3.CHECK SERVICE PLUG GRIP (CONNECTION CONDITION)

B

10.CHECK REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY (HV FLOOR UNDER WIRE CONNECTION CONDITION)
3.CHECK SERVICE PLUG GRIP (CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


a.

Visually check the connection of the service plug grip to the HV battery. Remove the service plug grip and check for contamination.

OK:

Dirt or foreign matter has not entered the connectors, and there is no evidence of contamination.



b.

Install the service plug grip.


Result:
Proceed to
OK
NG



OK

4.INSPECT SERVICE PLUG GRIP

NG

4.INSPECT SERVICE PLUG GRIP
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Procedure1

a.
A365294C06
0.104,0.083 0.417,0.24 0.313,0.156 10 false *1
*1 Service Plug Grip


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Service plug grip terminals Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the service plug grip.



OK

5.CHECK HYBRID BATTERY TERMINAL BLOCK

NG

5.CHECK HYBRID BATTERY TERMINAL BLOCK
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Remove the Hybrid battery terminal block.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>FUSE BOX>REMOVAL



Procedure1

a.
A367707C04
0.104,0.083 0.417,0.24 0.313,0.156 10 false *1
*1 Hybrid Battery Terminal Block


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Hybrid battery terminal block Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the Hybrid battery terminal block.



OK

6.CHECK NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (HV FLOOR UNDER WIRE CONNECTION CONDITION)

NG

REPLACE HYBRID BATTERY TERMINAL BLOCK

6.CHECK NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (HV FLOOR UNDER WIRE CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



Procedure1

a.
A458497N02
2.094,1.448 2.417,1.708 0.323,0.26 1.719,1.74 2.042,2 0.323,0.26 1.813,1.792 1.99,1.958 0.177,0.167 10 true a1 2.177,1.5 2.365,1.677 0.188,0.177 10 true a2

Check the HV floor under wire is connected securely, and there are no contact problems.


b.

Disconnect the HV floor under wire connectors from the No. 1 traction battery device box assembly.


c.

Check for arc marks on the terminals of the HV floor under wire and the No. 1 traction battery device box assembly.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



Post-procedure1

a.

Reconnect the HV floor under wire connectors.


b.

Install the HV battery upper cover panel.



A

7.CHECK FLOOR UNDER WIRE

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

7.CHECK FLOOR UNDER WIRE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
A458497N02
2.094,1.448 2.417,1.708 0.323,0.26 1.719,1.74 2.042,2 0.323,0.26 1.813,1.792 1.99,1.958 0.177,0.167 10 true a1 2.177,1.5 2.365,1.677 0.188,0.177 10 true a2

Disconnect the HV floor under wire connectors from the No. 1 traction battery device box assembly.


d.
A475630

Disconnect the HV floor under wire connector from the hybrid motor control inverter assembly.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A409066C30
1.875,0.875 2.271,1.115 0.396,0.24 3.74,0.531 4.135,0.771 0.396,0.24 5.625,0.531 6.021,0.771 0.396,0.24 1.281,1.958 1.917,1.677 true 3.948,1.146 4.333,0.708 true 5.771,1.073 5.396,0.708 true 2.781,1.865 2.208,1.677 true 1.281,1.24 1.594,1.24 true 6.26,2.365 6.573,2.365 true 0.594,0.5 0.906,0.656 0.313,0.156 10 false *a 3.594,0.208 3.906,0.365 0.313,0.156 10 false *b 2,0.938 2.313,1.135 0.313,0.198 10 false a3 3.865,0.573 4.177,0.771 0.313,0.198 10 false a1 5.76,0.583 6.073,0.781 0.313,0.198 10 false a2 1.021,1.906 1.479,2.104 0.458,0.198 10 false CBI 3.677,1.083 4.135,1.281 0.458,0.198 10 false CBI 5.823,1.021 6.281,1.219 0.458,0.198 10 false CEI 2.844,1.781 3.302,1.979 0.458,0.198 10 false CEI 1.115,1.188 1.427,1.344 0.313,0.156 10 false *1 6.646,2.313 6.958,2.469 0.313,0.156 10 false *1
*1 Shield Ground - -
*a HV Floor Under Wire
(Hybrid Motor Control Inverter Assembly Side)
*b HV Floor Under Wire
(No. 1 Traction Battery Device Box Assembly Side)


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(a3,a1,a2)Location & Routing

Click Connector(a3)Engine Compartment>HV Floor Under Wire>Hybrid Motor Control Inverter Assembly

Click Connector(a1)Body>HV Floor Under Wire>HV Battery Junction Block Assembly

Click Connector(a2)Body>HV Floor Under Wire>HV Battery Junction Block Assembly

a3-1 (CBI) - a1-1 (CBI) Ignition switch off Below 1 Ω
a3-2 (CEI) - a2-1 (CEI) Ignition switch off Below 1 Ω


NOTICE:

Be sure not to damage or deform the terminal being inspected.



b.

Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(a3,a1,a2)Location & Routing

Click Connector(a3)Engine Compartment>HV Floor Under Wire>Hybrid Motor Control Inverter Assembly

Click Connector(a1)Body>HV Floor Under Wire>HV Battery Junction Block Assembly

Click Connector(a2)Body>HV Floor Under Wire>HV Battery Junction Block Assembly

a3-1 (CBI) or a1-1 (CBI) - Body ground and shield ground Ignition switch off 10 MΩ or higher
a3-2 (CEI) or a2-1 (CEI) - Body ground and shield ground Ignition switch off 10 MΩ or higher
a3-1 (CBI) - a3-2 (CEI) Ignition switch off 10 MΩ or higher
a1-1 (CBI) - a2-1 (CEI) Ignition switch off 10 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the HV floor under wire connectors.


b.

Install the HV battery upper cover panel.



OK

8.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRB)

NG

8.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRB)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 traction battery device box assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A458079C07
3.771,1.031 4.125,1.281 0.354,0.25 3.26,0.094 3.625,0.344 0.365,0.25 6.219,0.698 6.615,0.917 0.396,0.219 3.156,1.51 3.417,1.26 true 3.771,1.49 3.604,1.271 true 3.448,0.719 3.917,0.26 true 6.313,1.198 5.813,0.802 true 0.573,0.146 0.885,0.302 0.313,0.156 10 false *a 3.844,1.094 4.302,1.292 0.458,0.198 10 false O70 2.906,1.542 3.24,1.75 0.333,0.208 10 true GND 3.781,1.521 4.24,1.719 0.458,0.198 10 true SMRB 6.323,0.74 6.583,0.885 0.26,0.146 10 true z10 3.979,0.177 4.438,0.375 0.458,0.198 10 false CBI 3.385,0.135 3.594,0.302 0.208,0.167 10 true a1 6.406,1.198 6.563,1.396 0.156,0.198 10 false +
*a Component without harness connected
(No. 1 Traction Battery Device Box Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z10,a1)Location & Routing

Click Connector(z10)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assembly

Click Connector(a1)Body>HV Floor Under Wire>HV Battery Junction Block Assembly

z10-1 (+) - a1-1 (CBI) Auxiliary battery voltage not applied between terminals O70-1 (SMRB) and O70-3 (GND) 10 kΩ or higher
z10-1 (+) - a1-1 (CBI) Auxiliary battery voltage applied between terminals O70-1 (SMRB) and O70-3 (GND) Below 1 Ω



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O70)Location & Routing

Click Connector(O70)Body>Floor Wire>HV Battery Junction Block Assembly

O70-1 (SMRB) - O70-3 (GND) -40 to 80°C (-40 to 176°F) 19.0 to 59.0 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the No. 1 traction battery device box assembly.



OK

9.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRG)

NG

REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

9.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRG)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 traction battery device box assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A458079C11
3.781,1.021 4.125,1.292 0.344,0.271 2.271,0.083 2.635,0.333 0.365,0.25 0.458,0.542 0.854,0.76 0.396,0.219 3.198,1.521 3.365,1.26 true 3.615,1.49 3.448,1.271 true 1.979,1.24 2.448,0.781 true 0.677,1.188 1.385,0.75 true 0.573,0.146 0.885,0.302 0.313,0.156 10 false *a 3.844,1.094 4.302,1.292 0.458,0.198 10 false O70 3.5,1.542 3.833,1.75 0.333,0.208 10 true GND 2.948,1.542 3.406,1.74 0.458,0.198 10 true SMRG 0.604,0.583 0.813,0.729 0.208,0.146 10 true z9 1.833,1.25 2.292,1.448 0.458,0.198 10 false CEI 2.406,0.135 2.615,0.302 0.208,0.167 10 true a2 0.604,1.167 0.76,1.365 0.156,0.198 10 false -
*a Component without harness connected
(No. 1 Traction Battery Device Box Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z9,a2)Location & Routing

Click Connector(z9)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assembly

Click Connector(a2)Body>HV Floor Under Wire>HV Battery Junction Block Assembly

z9-1 (-) - a2-1 (CEI) Auxiliary battery voltage not applied between terminals O70-4 (SMRG) and O70-3 (GND) 10 kΩ or higher
z9-1 (-) - a2-1 (CEI) Auxiliary battery voltage applied between terminals O70-4 (SMRG) and O70-3 (GND) Below 1 Ω



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O70)Location & Routing

Click Connector(O70)Body>Floor Wire>HV Battery Junction Block Assembly

O70-4 (SMRG) - O70-3 (GND) -40 to 80°C (-40 to 176°F) 19.0 to 59.0 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the No. 1 traction battery device box assembly.



OK

HV BATTERY HIGH-VOLTAGE LINE CIRCUIT NORMAL (PERFORM NEXT STEP FOR REFERENCED DTC)

NG

REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

10.CHECK REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY (HV FLOOR UNDER WIRE CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove inverter terminal cover from the rear hybrid motor control inverter assembly.


c.

Check that the bolts for the HV floor under wire is tightened to the specified torque, the HV floor under wire is connected securely, and there are no contact problems.

Specified Condition:

T = 8.0 N*m (82 kgf*cm)



d.
A475631

A475646N01
1.604,0.198 2.021,0.49 0.417,0.292 1.74,0.281 1.969,0.458 0.229,0.177 10 true a4

Disconnect the HV floor under wire from the rear hybrid motor control inverter assembly.


Procedure1

a.

Check for arc marks on the terminals for the HV floor under wire and hybrid motor control inverter assembly.

Result:
Result Proceed to
The terminals are not connected securely and there is a contact problem. There are no arc marks. A
The terminals are connected securely and there are no contact problems. There are arc marks. B
The terminals are connected securely and there are no contact problems. There are no arc marks. C
The terminals are not connected securely and there is a contact problem. There are arc marks. B



Post-procedure1

a.

Reconnect the HV floor under wire to the rear hybrid motor control inverter assembly.


b.

Install the inverter terminal cover from the rear hybrid motor control inverter assembly.



A

11.CHECK REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY (HYBRID BATTERY PACK WIRE CONNECTION CONDITION)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

11.CHECK REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY (HYBRID BATTERY PACK WIRE CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove inverter terminal cover from the rear hybrid motor control inverter assembly.


c.
A475631

A475624N01
2.354,0.375 2.729,0.667 0.375,0.292 2.469,0.448 2.656,0.615 0.188,0.167 10 true c6

Check that the bolts for the HV battery pack wire is tightened to the specified torque, the HV battery pack wire is connected securely, and there are no contact problems.

Specified Condition:

T = 8.0 N*m (82 kgf*cm)



d.

Disconnect the HV battery pack wire from the rear hybrid motor control inverter assembly.


Procedure1

a.

Check for arc marks on the terminals for the HV battery pack wire and rear hybrid motor control inverter assembly.

Result:
Result Proceed to
The terminals are not connected securely and there is a contact problem. There are no arc marks. A
The terminals are connected securely and there are no contact problems. There are arc marks. B
The terminals are connected securely and there are no contact problems. There are no arc marks. C
The terminals are not connected securely and there is a contact problem. There are arc marks. B



Post-procedure1

a.

Reconnect the HV battery pack wire to the rear hybrid motor control inverter assembly.


b.

Install the inverter terminal cover from the rear hybrid motor control inverter assembly.



A

12.CHECK SERVICE PLUG GRIP (CONNECTION CONDITION)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

12.CHECK SERVICE PLUG GRIP (CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


a.

Visually check the connection of the service plug grip to the HV battery. Remove the service plug grip and check for contamination.

OK:

Dirt or foreign matter has not entered the connectors, and there is no evidence of contamination.



b.

Install the service plug grip.


Result:
Proceed to
OK
NG



OK

13.INSPECT SERVICE PLUG GRIP

NG

13.INSPECT SERVICE PLUG GRIP
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Procedure1

a.
A365294C06
0.104,0.083 0.417,0.24 0.313,0.156 10 false *1
*1 Service Plug Grip


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Service plug grip terminals Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the service plug grip.



OK

14.CHECK HYBRID BATTERY TERMINAL BLOCK

NG

14.CHECK HYBRID BATTERY TERMINAL BLOCK
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Remove the Hybrid battery terminal block.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>FUSE BOX>REMOVAL



Procedure1

a.
A367707C04
0.104,0.083 0.417,0.24 0.313,0.156 10 false *1
*1 Hybrid Battery Terminal Block


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Hybrid battery terminal block Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the Hybrid battery terminal block.



OK

15.CHECK NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (HV FLOOR UNDER WIRE CONNECTION CONDITION)

NG

REPLACE HYBRID BATTERY TERMINAL BLOCK

15.CHECK NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (HV FLOOR UNDER WIRE CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



Procedure1

a.
A458497N03
2.094,1.448 2.417,1.708 0.323,0.26 1.719,1.74 2.042,2 0.323,0.26 1.813,1.792 1.99,1.958 0.177,0.167 10 true c1 2.177,1.5 2.365,1.677 0.188,0.177 10 true c2

Check the HV floor under wire is connected securely, and there are no contact problems.


b.

Disconnect the HV floor under wire connectors from the No. 1 traction battery device box assembly.


c.

Check for arc marks on the terminals of the HV floor under wire and the No. 1 traction battery device box assembly.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



Post-procedure1

a.

Reconnect the HV floor under wire connectors.


b.

Install the HV battery upper cover panel.



A

16.CHECK FLOOR UNDER WIRE

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

16.CHECK FLOOR UNDER WIRE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A475630

Disconnect the HV floor under wire connector from the hybrid motor control inverter assembly.


c.
A475631

Remove the inverter terminal cover from the rear hybrid motor control inverter assembly.


d.
A475646N01
1.604,0.198 2.021,0.49 0.417,0.292 1.74,0.281 1.969,0.458 0.229,0.177 10 true a4

Disconnect HV floor under wire connector from the rear hybrid motor control inverter assembly.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A378818C14
1.906,0.844 2.24,1.083 0.333,0.24 5.073,0.969 5.406,1.208 0.333,0.24 1.896,1.656 1.208,2.354 true 2.208,1.667 2.844,2.344 true 5.01,2.073 4.469,2.844 true 5.438,2.073 5.969,2.823 true 6.177,1.427 5.885,1.427 true 2.823,1.229 2.531,1.229 true 0.781,0.74 1.094,0.896 0.313,0.156 10 false *a 4.115,0.771 4.427,0.927 0.313,0.156 10 false *b 1.094,2.385 1.479,2.604 0.385,0.219 10 false CBI 2.802,2.375 3.188,2.594 0.385,0.219 10 false CEI 2.01,0.896 2.396,1.115 0.385,0.219 10 false a3 5.177,1.01 5.563,1.229 0.385,0.219 10 false a4 4.24,2.865 4.75,3.115 0.51,0.25 10 false RCEO 5.865,2.875 6.375,3.125 0.51,0.25 10 false RCBO 6.24,1.375 6.552,1.531 0.313,0.156 10 false *1 2.896,1.177 3.208,1.333 0.313,0.156 10 false *1
*1 Shield Ground - -
*a HV Floor Under Wire
(Hybrid Motor Control Inverter Assembly Side)
*b HV Floor Under Wire
(Rear Hybrid Motor Control Inverter Assembly Side)


Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(a3,a4)Location & Routing

Click Connector(a3)Engine Compartment>HV Floor Under Wire>Hybrid Motor Control Inverter Assembly

Click Connector(a4)Body>HV Floor Under Wire>Rear Hybrid Motor Control Inverter Assembly

a3-1 (CBI) - a4-2 (RCBO) Ignition switch off Below 1 Ω
a3-2 (CEI) - a4-1 (RCEO) Ignition switch off Below 1 Ω


NOTICE:

Be sure not to damage or deform the terminal being inspected.



b.

Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(a3,a4)Location & Routing

Click Connector(a3)Engine Compartment>HV Floor Under Wire>Hybrid Motor Control Inverter Assembly

Click Connector(a4)Body>HV Floor Under Wire>Rear Hybrid Motor Control Inverter Assembly

a3-1 (CBI) or a4-2 (RCBO) - Body ground and shield ground Ignition switch off 10 MΩ or higher
a3-2 (CEI) or a4-1 (RCEO) - Body ground and shield ground Ignition switch off 10 MΩ or higher
a3-1 (CBI) - a3-2 (CEI) Ignition switch off 10 MΩ or higher
a4-2 (RCBO) - a4-1 (RCEO) Ignition switch off 10 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the HV floor under wire connector to the hybrid motor control inverter assembly.


b.

Install the inverter terminal cover to the rear hybrid motor control inverter assembly.


c.

Reconnect HV floor under wire connector from the rear hybrid motor control inverter assembly.



OK

17.CHECK HV BATTERY PACK WIRE

NG

17.CHECK HV BATTERY PACK WIRE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
A458497N03
2.094,1.448 2.417,1.708 0.323,0.26 1.719,1.74 2.042,2 0.323,0.26 1.813,1.792 1.99,1.958 0.177,0.167 10 true c1 2.177,1.5 2.365,1.677 0.188,0.177 10 true c2

Disconnect the HV battery pack wire connectors from the No. 1 traction battery device box assembly.


d.
A475631

Remove the inverter terminal cover from the rear hybrid motor control inverter assembly.


e.
A475624N01
2.354,0.375 2.729,0.667 0.375,0.292 2.469,0.448 2.656,0.615 0.188,0.167 10 true c6

Disconnect the HV battery pack wire from the rear hybrid motor control inverter assembly.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A378817C16
1.74,1.031 2.083,1.271 0.344,0.24 3.802,0.521 4.146,0.76 0.344,0.24 5.604,0.531 5.948,0.771 0.344,0.24 1.667,2.042 1.156,2.729 true 2.115,2.042 2.615,2.74 true 4.396,0.698 3.958,1.177 true 5.333,0.698 5.76,1.167 true 2.875,1.406 2.552,1.406 true 6.573,2.365 6.25,2.365 true 0.802,0.552 1.115,0.708 0.313,0.156 10 false *a 3.552,0.177 3.865,0.333 0.313,0.156 10 false *b 0.979,2.75 1.5,2.938 0.521,0.188 10 false RCBI 2.5,2.76 3.021,2.948 0.521,0.188 10 false RCEI 3.792,1.198 4.313,1.385 0.521,0.188 10 false CBI 5.75,1.198 6.271,1.385 0.521,0.188 10 false CEI 3.917,0.563 4.24,0.729 0.323,0.167 10 false c1 5.719,0.573 6.042,0.74 0.323,0.167 10 false c2 1.844,1.073 2.167,1.24 0.323,0.167 10 false c6 2.927,1.333 3.24,1.49 0.313,0.156 10 false *1 6.615,2.302 6.927,2.458 0.313,0.156 10 false *1
*1 Shield Ground - -
*a HV Battery Pack Wire
(Rear Hybrid Motor Control Inverter Assembly Side)
*b HV Battery Pack Wire
(Hybrid Battery Junction Clock Assembly Side)


Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(c6,c1,c2)Location & Routing

Click Connector(c6)Body>HV Battey Pack Wire>Rear Hybrid Motor Control Inverter Assembly

Click Connector(c1)Body>HV Battey Pack Wire>HV Battery Junction Block Assembly

Click Connector(c2)Body>HV Battey Pack Wire>HV Battery Junction Block Assembly

c6-1 (RCBI) - c1-1 (CBI) Ignition switch off Below 1 Ω
c6-2 (RCEI) - c2-1 (CEI) Ignition switch off Below 1 Ω



b.

Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(c6,c1,c2)Location & Routing

Click Connector(c6)Body>HV Battey Pack Wire>Rear Hybrid Motor Control Inverter Assembly

Click Connector(c1)Body>HV Battey Pack Wire>HV Battery Junction Block Assembly

Click Connector(c2)Body>HV Battey Pack Wire>HV Battery Junction Block Assembly

c6-1 (RCBI) or c1-1 (CBI) - Body ground and shield ground Ignition switch off 10 MΩ or higher
c6-2 (RCEI) or c2-1 (CEI) - Body ground and shield ground Ignition switch off 10 MΩ or higher
c6-1 (RCBI) - c1-1 (CBI) Ignition switch off 10 MΩ or higher
c6-2 (RCEI) - c2-1 (CEI) Ignition switch off 10 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the HV battery pack wire to the rear hybrid motor control inverter assembly.


b.

Install the inverter terminal cover from the rear hybrid motor control inverter assembly.


c.

Reconnect the HV battery pack wire to the No. 1 traction battery device box assembly.


d.

Install the HV battery upper cover panel.



OK

18.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRB)

NG

18.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRB)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 traction battery device box assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A458079C09
3.792,1.031 4.156,1.26 0.365,0.229 3.26,0.094 3.625,0.344 0.365,0.25 6.219,0.698 6.615,0.917 0.396,0.219 3.156,1.51 3.417,1.26 true 3.771,1.49 3.604,1.271 true 3.448,0.719 3.917,0.26 true 6.313,1.198 5.813,0.802 true 0.573,0.146 0.885,0.302 0.313,0.156 10 false *a 3.865,1.083 4.323,1.281 0.458,0.198 10 false O70 2.906,1.542 3.24,1.75 0.333,0.208 10 true GND 3.781,1.521 4.24,1.719 0.458,0.198 10 true SMRB 6.323,0.74 6.583,0.885 0.26,0.146 10 true z10 3.979,0.177 4.438,0.375 0.458,0.198 10 false CBI 3.385,0.135 3.594,0.302 0.208,0.167 10 true c1 6.406,1.198 6.563,1.396 0.156,0.198 10 false +
*a Component without harness connected
(No. 1 Traction Battery Device Box Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z10,c1,z9)Location & Routing

Click Connector(z10)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assembly

Click Connector(c1)Body>HV Battey Pack Wire>HV Battery Junction Block Assembly

Click Connector(z9)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assembly

z10-1 (+) - c1-1 (CBI) Auxiliary battery voltage not applied between terminals O70-1 (SMRB) and O70-3 (GND) 10 kΩ or higher
z9-1 (+) - c1-1 (CBI) Auxiliary battery voltage applied between terminals O70-1 (SMRB) and O70-3 (GND) Below 1 Ω



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O70)Location & Routing

Click Connector(O70)Body>Floor Wire>HV Battery Junction Block Assembly

O70-1 (SMRB) - O70-3 (GND) -40 to 80°C (-40 to 176°F) 19.0 to 59.0 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the No. 1 traction battery device box assembly.



OK

19.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRG)

NG

REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

19.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRG)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 traction battery device box assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A458079C12
3.792,1.031 4.156,1.271 0.365,0.24 2.271,0.094 2.635,0.333 0.365,0.24 1.177,0.094 1.542,0.333 0.365,0.24 3.208,1.51 3.365,1.26 true 3.667,1.521 3.458,1.26 true 2.125,1.167 2.458,0.781 true 0.865,0.917 1.375,0.719 true 0.573,0.146 0.885,0.302 0.313,0.156 10 false *a 3.865,1.083 4.323,1.281 0.458,0.198 10 false O70 3.615,1.552 3.948,1.76 0.333,0.208 10 true GND 2.99,1.531 3.448,1.74 0.458,0.208 10 true SMRG 1.302,0.146 1.49,0.313 0.188,0.167 10 true z9 2.385,0.135 2.583,0.302 0.198,0.167 10 true c2 1.885,1.146 2.26,1.354 0.375,0.208 10 false CEI 0.74,0.885 0.896,1.083 0.156,0.198 10 false -
*a Component without harness connected
(No. 1 Traction Battery Device Box Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z9,c2)Location & Routing

Click Connector(z9)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assembly

Click Connector(c2)Body>HV Battey Pack Wire>HV Battery Junction Block Assembly

z9-1 (-) - c2-1 (CEI) Auxiliary battery voltage not applied between terminals O70-4 (SMRG) and O70-3 (GND) 10 kΩ or higher
z9-1 (-) - c2-1 (CEI) Auxiliary battery voltage applied between terminals O70-4 (SMRG) and O70-3 (GND) Below 1 Ω



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O70)Location & Routing

Click Connector(O70)Body>Floor Wire>HV Battery Junction Block Assembly

O70-4 (SMRG) - O70-3 (GND) -40 to 80°C (-40 to 176°F) 19.0 to 59.0 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the No. 1 traction battery device box assembly.



OK

HV BATTERY HIGH-VOLTAGE LINE CIRCUIT NORMAL (PERFORM NEXT STEP FOR REFERENCED DTC)

NG

REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY