Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HV BATTERY › 2020.08–2021.07
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441190 HV BATTERY A

HYBRID / BATTERY CONTROL  HV BATTERY  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A472777N06
1.5,0.25 1.75,0.25 false 6.542,0.198 6.875,0.198 false 3.396,0.625 3.729,0.625 false 3.99,3.323 4.333,3.323 false 5.781,0.063 6.917,0.406 1.135,0.344 18 false 1, 2, 6 4.177,0.479 4.896,0.823 0.719,0.344 18 false 5, 7 1.073,0.146 1.792,0.49 0.719,0.344 18 false 4, 8 3.781,3.188 4.5,3.531 0.719,0.344 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 READ VALUE USING GTS - - - -
3 SERVICE PLUG GRIP G3834 (Click here) - -
4 DISCONNECT ENGINE WIRE 82121 (Click here) - -
5 CONNECTOR COVER ASSEMBLY - (Click here) - -
6 TERMINAL VOLTAGE - (Click here) - -
7 CONNECTOR COVER ASSEMBLY - (Click here) - -
8 CONNECT ENGINE WIRE 82121 (Click here) - -

A461204N06
1.344,1.333 2.823,1.333 false 2.708,2.104 2.708,1.333 false 5.396,0.667 5.729,0.667 false 5.292,1.667 6,1.667 false 6.135,3.958 6.469,3.958 false 2.635,4.167 2.969,4.167 false 5.865,0.542 6.146,0.896 0.281,0.354 18 false 9 6.146,1.542 6.542,1.896 0.396,0.354 18 false 10 3.104,1.198 3.5,1.552 0.396,0.354 18 false 11 3.063,4.01 3.458,4.365 0.396,0.354 18 false 12 6.146,3.406 6.458,3.604 0.313,0.198 10 false x6 2.917,1.24 3.313,1.594 0.396,0.354 10 false ● 6.594,3.813 6.99,4.167 0.396,0.354 18 false 13

Procedure Part Name Code
Z101186

Z101188

Z101187

9 REAR CENTER SEAT OUTER BELT ASSEMBLY 73350C - - -
10 BENCH TYPE REAR SEAT CUSHION ASSEMBLY - - - -
11 REAR SEAT CUSHION LOCK HOOK 72693 - - -
12 REAR UNDER COVER 76971G - - -
13 REAR SEAT CUSHION LEG SUB-ASSEMBLY 71033 - - -

● Non-reusable part - -

A478805N01
5.344,5.167 5.594,5.167 false 4.531,4.333 4.833,4.333 false 6.042,2.615 6.177,2.615 false 5.948,1.385 5.948,1.552 false 6.458,0.25 6.76,0.25 false 1.271,0.833 1.573,0.833 false 0.542,2.792 0.844,2.792 false 2.365,1.833 2.083,1.833 false 5.833,3.5 5.833,3.333 false 6.167,1.635 6.719,1.99 0.552,0.354 18 false 14 6.552,2.406 7.104,2.76 0.552,0.354 18 false 15 1.656,0.677 2.208,1.031 0.552,0.354 18 false 18 4.927,4.188 5.479,4.542 0.552,0.354 18 false 20 1.792,1.729 2.344,2.083 0.552,0.354 18 false 16 6.083,0.104 6.635,0.458 0.552,0.354 18 false 21 1.271,3.354 1.583,3.552 0.313,0.198 10 false x3 5.635,0.438 5.948,0.635 0.313,0.198 10 false x3 5.698,2.573 6.01,2.771 0.313,0.198 10 false x5 6.052,3.552 6.604,3.906 0.552,0.354 18 false 15 5.938,5 6.49,5.354 0.552,0.354 18 false 17 0.198,2.656 0.75,3.01 0.552,0.354 18 false 19

Procedure Part Name Code
Z101186

Z101188

Z101187

14 BATTERY COOLING BLOWER ASSEMBLY G9230 (Click here) - -
15 HV BATTERY UPPER COVER PANEL G92N1 (Click here) - -
16 HV FLOOR UNDER WIRE 821H1 (Click here) - -
17 DISCONNECT FLOOR WIRE 82161 (Click here) - -
18 HYBRID BATTERY HOSE ASSEMBLY G9290 - - -
19 DISCONNECT FLOOR WIRE 82161 - - -
20 HV BATTERY G9510 - - -
21 RECOVERY INSPECTION - (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during HV battery removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Replacement of HV battery
1.

Prediagnostic battery charge

2.

Battery diagnosis

3.

Battery status info update


HV battery status information cannot be updated (Click here)
Replacement of hybrid battery terminal block Perform high voltage fuse accumulated load history reset DTCs are stored (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



HINT:
·

When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

·

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

If the HV battery has been struck or dropped, replace it.

·

When connecting a connector to the HV battery, confirm that the connector is securely connected through the following:

- Push the connector until a click sound is heard.

- Visually check and confirm that the connector is securely connected by pulling on it.

·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.

·

When performing repairs around the HV battery, such as using a tap, do not allow metal shavings to enter the HV battery.

·

Do not touch any high voltage wire harnesses, connectors or parts with bare hands.

·
A457840

Hold the areas shown in the illustration and lift the HV battery.

·

Do not allow foreign matter, such as grease or oil, to adhere to the bolts or nuts of the HV battery.

·
A457841C02
0.99,2.521 0.458,2.042 0.458,2.042 0.885,1.125 true 0.229,1.958 0.542,2.115 0.313,0.156 10 false *a
*a Opening


Do not put your hands into the openings of the HV battery.

·

When removing/installing/moving the HV battery assembly, make sure not to tilt it more than 80°.

·

Do not climb on top of or stand on the HV battery.

·

Do not allow any foreign matter or water to enter the HV battery.

·

If any bolts, nuts or clips are dropped into the HV battery, make sure to remove them.



Hide 2. READ VALUE USING GTS

a.
A461168N07
0.5,0.094 1.521,0.417 1.021,0.323 18 false i, ii, iii, iv

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch on (IG).


iii.

Enter the following menus: Powertrain / HV Battery / Data List / Hybrid/EV Battery Temperature 1 to 6.

Powertrain > HV Battery > Data List
Tester Display
Hybrid/EV Battery Temperature 1
Hybrid/EV Battery Temperature 2
Hybrid/EV Battery Temperature 3
Hybrid/EV Battery Temperature 4
Hybrid/EV Battery Temperature 5
Hybrid/EV Battery Temperature 6
50003 398 62,63,64,65,66,67

iv.

Read the Data List.

NOTICE:

If any of the temperatures listed in "Hybrid/EV Battery Temperature 1 to 6" are 50°C or more, leave the vehicle until the temperature drops to less than 50°C.




Hide 82121 4.DISCONNECT ENGINE WIRE

Z101186

Click here(Click here)

Hide 5.REMOVE CONNECTOR COVER ASSEMBLY

Z101186

Click here(Click here)

Hide 6.CHECK TERMINAL VOLTAGE

Z101186

Click here(Click here)

Hide 7.INSTALL CONNECTOR COVER ASSEMBLY

Z101186

CAUTION:

Wear insulated gloves.



a.
A457980C04
3.917,1.125 4.125,1.302 0.208,0.177 10 true *a 3.74,0.344 3.969,0.5 0.229,0.156 10 true *b
*a Bolt (A) *b Bolt (B)


i.

Using a T25 "TORX" socket wrench, install the connector cover assembly to the inverter with converter assembly with the bolt (A).

Torque:
4.5 N*m (46 kgf*cm, 40 in.*lbf)

NOTICE:

Do not touch the waterproof seal of the connector cover assembly.



ii.

Install the bolt (B).

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)



Hide 82121 8.CONNECT ENGINE WIRE

Z101186

Click here(Click here)

Hide 73350C 9.DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY

Hide 10.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 72693 11.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 76971G 12.REMOVE REAR UNDER COVER

a.
A457850


Hide 71033 13.REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY

a.
A457851


Hide G9230 14.REMOVE BATTERY COOLING BLOWER ASSEMBLY

Z101186

Click here(Click here)

Hide G92N1 15.REMOVE HV BATTERY UPPER COVER PANEL

Z101186

CAUTION:

Wear insulated gloves.



a.
A457854C01
4.781,2.448 5.031,2.448 false 4.458,1.646 4.708,1.646 false 4.323,2.146 4.49,2.146 4.49,2.146 4.604,2.01 false 4.635,2.354 4.833,2.167 4.833,2.167 5,2.167 true 4.76,1.594 5.073,1.75 0.313,0.156 10 false *1 5.083,2.375 5.396,2.531 0.313,0.156 10 false *2 4.156,2.073 4.469,2.229 0.313,0.156 10 false *a 4.094,1.823 4.406,1.979 0.313,0.156 10 false *b 5.063,2.094 5.375,2.25 0.313,0.156 10 false *c 4.052,2.281 4.417,2.573 0.365,0.292 18 false i 2.271,0.052 2.5,0.354 0.229,0.302 18 true ii
*1 Service Plug Grip *2 Battery Cover Lock Striker
*a Projection *b Turn
*c Button - -


i.

Using the service plug grip, remove the battery cover lock striker.

HINT:

Insert the projection of the service plug grip and turn the button of the battery cover lock striker counterclockwise to release the lock.



ii.

Remove the 5 nuts and HV battery upper cover panel from the HV battery.



Hide 821H1 16.DISCONNECT FLOOR UNDER WIRE

Z101186

CAUTION:

Wear insulated gloves.


NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



a.
A460052C01
3.75,0.583 4.083,0.583 true 4.125,0.49 4.375,0.677 0.25,0.188 10 true *a 2.219,0.063 2.375,0.344 0.156,0.281 18 true i 3.792,0.177 4.01,0.458 0.219,0.281 18 true ii
*a Shield Ground - -


i.

Disconnect the 2 HV battery junction block assembly connectors.


ii.

Disconnect the shield ground from the HV battery.



Hide 82161 17.DISCONNECT FLOOR WIRE

Z101186

CAUTION:

Wear insulated gloves.



a.
A478806


Hide G9290A 18.REMOVE HYBRID BATTERY HOSE ASSEMBLY

a.
A457859


Hide 82161 19.DISCONNECT FLOOR WIRE

Z101186

CAUTION:

Wear insulated gloves.



a.
A457858


Hide G9510 20.REMOVE HV BATTERY

Z101186

CAUTION:

Wear insulated gloves.


NOTICE:
·

Do not allow foreign matter, such as grease or oil, to adhere to the bolts of the HV battery.

·

To prevent the wire harness from being caught, make sure to bundle the wire harness using insulating tape or equivalent.

·

Use cardboard or another similar material to protect the HV battery and vehicle body from damage.

·

Since the HV battery is very heavy, 2 people are needed to remove it. When removing the HV battery, be careful not to damage the parts around it.

·

When removing the HV battery from the vehicle, do not allow it to contact the vehicle.

·

When removing/installing/moving the HV battery, make sure not to tilt it more than 80°.

·

Insulate the disconnected terminals or connectors with insulating tape.

·

If the HV battery has been struck or dropped, replace it.




a.
A460054


Hide 21.PERFORM RECOVERY INSPECTION

a.
A461169N01
1.417,0.167 1.698,0.521 0.281,0.354 18 false i

i.

Before returning the HV battery, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION