Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441183 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0ABF00  Hybrid/EV Battery Current Sensor "A" Circuit Range/Performance  


DESCRIPTION

A battery current sensor, which is mounted on the positive cable side of each No. 1 traction battery device box assembly, detects the current flowing to or from the battery pack. The battery current sensor sends a voltage, which varies between 0 and 5 V in proportion to the amperage, to the IB0 terminal of the battery ECU assembly. Similarly, it sends a voltage, which varies between 0 and 5 V in inverse proportion to the amperage, to the IB1 terminal of the battery ECU assembly. When the voltage at the IB0 terminal is below 2.57 V and the voltage at the IB1 terminal is above 2.43 V, this indicates that the HV battery is being discharged. Additionally, Meanwhile, when the voltage at of the IB0 terminal is above 2.57 V and the voltage at of the IB1 terminal is below 2.43 V, this indicates that the HV battery is being charged. The battery ECU assembly sends the signals from its IB0 and IB1 terminals to the hybrid vehicle control ECU. The hybrid vehicle control ECU determines the charging and discharging amperage of the HV battery based on the received signals and calculates the SOC of the HV battery using the cumulative amperage value.

A460750E02
0.177,0.188 0.781,0.563 0.604,0.375 10 false Charging Current 1.167,0.167 1.958,0.552 0.792,0.385 10 false Discharging Current 1.219,1.26 2.177,1.615 0.958,0.354 10 false Battery Current Sensor 2.156,2.927 2.99,3.323 0.833,0.396 10 false Battery ECU Assembly 2.229,1.792 2.49,1.99 0.26,0.198 10 false VIB 2.229,1.979 2.49,2.177 0.26,0.198 10 false IB0 2.208,2.156 2.469,2.354 0.26,0.198 10 false GIB 2.219,2.323 2.479,2.521 0.26,0.198 10 false IB1 3.719,0.448 6.448,0.677 2.729,0.229 10 false Battery Current Sensor Output Voltage (V) 3.042,1.917 3.375,2.104 0.333,0.188 10 false (IB1) 6.802,2 7.135,2.188 0.333,0.188 10 false (IB0) 5.115,2.51 5.448,2.698 0.333,0.188 10 false IB0 5.896,1.802 6.229,1.99 0.333,0.188 10 false IB1 3.219,3.167 3.823,3.542 0.604,0.375 10 false Charging Current 6.302,3.188 7.094,3.573 0.792,0.385 10 false Discharging Current 4.219,3.458 5.948,3.688 1.729,0.229 10 false Hybrid Battery Current (A) 3.406,2.688 3.635,2.875 0.229,0.188 10 false 0.3 3.333,2.063 3.646,2.25 0.313,0.188 10 false 2.43 3.406,1.198 3.635,1.385 0.229,0.188 10 false 4.7 6.521,1.229 6.792,1.417 0.271,0.188 10 false 4.6 6.521,1.854 6.833,2.042 0.313,0.188 10 false 2.57 6.521,2.677 6.833,2.865 0.313,0.188 10 false 0.4 3.74,2.99 4.052,3.177 0.313,0.188 10 false -290 6.146,2.99 6.552,3.177 0.406,0.188 10 false +310 4.844,3 4.979,3.177 0.135,0.177 10 false 0

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
P0ABF00 Hybrid/EV Battery Current Sensor "A" Circuit Range/Performance Abnormal battery current sensor characteristics:
(based on hybrid system consumption and HV battery output).
(1 trip detection logic)
·

No. 1 traction battery device box assembly

·

Battery ECU assembly

·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly


Comes on Master Warning: Comes on Hybrid Control A

Related Data List
DTC No. Data List
P0ABF00 -

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Drive the vehicle for approximately 10 minutes according to the freeze frame data items "Vehicle Speed", "Accelerator Position", "Hybrid/EV Battery Current", "Motor Torque" and "Generator Torque".

4.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

A459771E06
1.792,0.49 2.344,0.906 0.552,0.417 10 false VIB 2.125,0.5 2.813,0.906 0.688,0.406 10 false 1 1.823,1.125 2.375,1.542 0.552,0.417 10 false IB0 1.833,1.76 2.385,2.177 0.552,0.417 10 false IB1 1.792,2.396 2.344,2.813 0.552,0.417 10 false GIB 2.115,1.156 2.802,1.563 0.688,0.406 10 false 4 2.146,1.802 2.833,2.208 0.688,0.406 10 false 2 2.125,2.417 2.813,2.823 0.688,0.406 10 false 3 0.354,3.073 2.75,3.427 2.396,0.354 10 false Battery Current Sensor (No. 1 Traction Battery Device Box Assembly) 5.135,0.49 5.688,0.906 0.552,0.417 10 false VIB 5.125,1.125 5.677,1.542 0.552,0.417 10 false IB0 5.146,1.76 5.698,2.177 0.552,0.417 10 false IB1 5.125,2.396 5.677,2.813 0.552,0.417 10 false GIB 5.052,3.281 6.802,3.552 1.75,0.271 10 false Battery ECU Assembly 4.865,0.5 5.156,0.74 0.292,0.24 10 false 31 4.844,1.125 5.094,1.323 0.25,0.198 10 false 19 4.917,1.75 5.063,1.938 0.146,0.188 10 false 8 4.917,2.396 5.146,2.646 0.229,0.25 10 false 7 5.052,3.115 5.604,3.531 0.552,0.417 10 false z12 0.354,2.875 0.906,3.292 0.552,0.417 10 false z11

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*

*: for AWD

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C58
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*.


*: for AWD

·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.

·
A358021C06
0.604,4.135 0.917,4.333 0.313,0.198 10 false *a 2.719,4.135 3.031,4.333 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

·

Before returning the HV battery, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION

·

Before returning the HV supply stack sub-assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery and HV supply stack sub-assemblies.

·
A358020

After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.



NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery hose.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



c.
A475640N01
0.958,0.292 1.354,0.542 0.396,0.25 1.052,0.344 1.302,0.521 0.25,0.177 10 true z12

Disconnect the z12 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A458502N02
0.656,1.135 1.073,1.396 0.417,0.26 0.75,1.188 1.021,1.344 0.271,0.156 10 true z11

Disconnect the z11 battery current sensor connector from the No. 1 traction battery device box assembly.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



Procedure1

a.
A459831C01
0.094,1.177 0.51,1.458 0.417,0.281 0.146,3.542 0.563,3.823 0.417,0.281 0.823,2.521 1.771,1.625 true 2.573,2.552 1.875,1.635 true 1.219,2.51 1.76,1.729 true 1.938,2.542 1.771,1.854 true 2.458,4.24 1.823,3.885 true 1.594,3.604 0.958,3.25 true 1.594,3.885 0.969,4.167 true 2.469,3.333 1.844,3.615 true 1.135,2.573 1.594,2.771 0.458,0.198 10 false IB0 1.854,2.604 2.313,2.802 0.458,0.198 10 false VIB 2.51,2.604 2.969,2.802 0.458,0.198 10 false IB1 0.708,2.563 1.167,2.76 0.458,0.198 10 false GIB 0.198,1.26 0.656,1.458 0.458,0.198 10 false z12 0.729,3.177 1.188,3.375 0.458,0.198 10 false VIB 0.729,4.135 1.188,4.333 0.458,0.198 10 false GIB 2.531,3.25 2.99,3.448 0.458,0.198 10 false IB1 2.552,4.219 3.01,4.417 0.458,0.198 10 false IB0 0.25,3.604 0.708,3.802 0.458,0.198 10 false z11 0.094,0.167 0.406,0.365 0.313,0.198 10 false *a 0.177,2.927 0.49,3.125 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Battery ECU Assembly)
*b Front view of wire harness connector
(to HV Battery Current Sensor Connector)


Measure the resistance according to the value(s) in the tables below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition

Click Location & Routing(z12,z11)Location & Routing

Click Connector(z12)Body>other>Battery ECU Assembly , HV Supply Battery Assembly

Click Connector(z11)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assembly

z12-8 (IB1) - z11-2 (IB1) Ignition switch off Below 1 Ω
z12-7 (GIB) - z11-3 (GIB) Ignition switch off Below 1 Ω
z12-19 (IB0) - z11-4 (IB0) Ignition switch off Below 1 Ω
z12-31 (VIB) - z11-1 (VIB) Ignition switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(z12,z11)Location & Routing

Click Connector(z12)Body>other>Battery ECU Assembly , HV Supply Battery Assembly

Click Connector(z11)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assembly

z12-8 (IB1) or z11-2 (IB1) - Body ground and other terminals Ignition switch off 10 kΩ or higher
z12-7 (GIB) or z11-3 (GIB) - Body ground and other terminals Ignition switch off 10 kΩ or higher
z12-19 (IB0) or z11-4 (IB0) - Body ground and other terminals Ignition switch off 10 kΩ or higher
z12-31 (VIB) or z11-1 (VIB) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the z12 battery ECU assembly connector.


b.

Reconnect the z11 battery current sensor connector from the No. 1 traction battery device box assembly.


c.

Install the No. 1 HV battery hose.



OK

2.REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY

NG

REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

2.REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY

NEXT

3.CLEAR DTC
3.CLEAR DTC

NEXT

4.PERFORM ROAD TEST
4.PERFORM ROAD TEST

Pre-procedure1

a.

Check that "Hybrid/EV Battery SOC" shows 60% or less.

Powertrain > Hybrid Control > Data List
Tester Display
Hybrid/EV Battery SOC
50003 397 320
HINT:

If "Hybrid/EV Battery SOC" is 60% or more, reduce it to below 60% by leaving the hybrid system on with shift lever in N.



Procedure1

a.

Apply the parking brake and secure the wheels using chocks.


b.

Turn the ignition switch to ON (READY).


c.

Move the shift lever to D while depressing the brake pedal with your left foot and repeat the following steps for 1 minute or more.

HINT:

Depress and release the accelerator pedal in 5-second intervals (2.5 seconds each) continuously.


i.

While depressing the brake pedal with your left foot, depress the accelerator pedal with your right foot.


ii.

Release the accelerator pedal.

Result:
Proceed to
NEXT




Post-procedure1

a.

Turn the ignition switch off.



NEXT

5.CHECK DTC OUTPUT (HYBRID CONTROL)
5.CHECK DTC OUTPUT (HYBRID CONTROL)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P0ABF00 is not output A
P0ABF00 is output B



Post-procedure1

a.

Turn the ignition switch off.



A

END

B