Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441183 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P1C2D62  Hybrid/EV Battery "A" Voltage Sensor/Boosting Converter Voltage Sensor "A" Signal Compare Failure  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The hybrid vehicle control ECU detects a VB sensor or VL sensor malfunction.

The cause of this malfunction may be one of the following:

Inverter voltage (VB or VL) sensor internal circuit malfunction
·

Voltage sensor malfunction

·

Motor generator control ECU (MG ECU) malfunction

·

Communication (wire harness) malfunction


High voltage system malfunction
·

HV battery malfunction

·

No. 1 traction battery device box assembly malfunction

·

Hybrid motor control inverter assembly malfunction

·

High-voltage wire harness malfunction

·

High-voltage connector or connection malfunction



Inspection Overview


Inspection Content Reason (Narrow Down in Order Using Inspection Procedures Below) Inspection Step
Check for DTCs (HV) Output DTCs 1
Check for DTCs (check voltage sensor malfunction locations)
Check for DTCs (drive test)
Ignition switch to ON (READY) (vehicle stopped or being driven) and then check whether DTCs are output again. 3, 4
Read value using GTS Data List value 5
Check freeze frame data (HV) Freeze Frame Data 6
Read value using GTS Accelerator and brake pedal simultaneously depressed Data List value 7


DESCRIPTION

For a description of the boost converter.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>P0CA300

The MG ECU uses a voltage sensor (VL) that is built into the boost converter to detect the high voltage before it is boosted. The ECU also uses the battery ECU assembly to detect HV battery voltage (VB).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
P1C2D62 Hybrid/EV Battery "A" Voltage Sensor/Boosting Converter Voltage Sensor "A" Signal Compare Failure Voltages from HV battery voltage (VB) sensor and boost converter voltage (VL) sensor deviate:
Difference between "VL-Voltage before Boosting" and "Hybrid/EV Battery Voltage" is large when the boosting request is given.
(1 trip detection logic)
·

Hybrid motor control inverter assembly

·

Battery ECU assembly


Comes on Master Warning: Comes on Hybrid Control A

Related Data List
DTC No. Data List
P1C2D62
·

Hybrid/EV Battery Voltage

·

VL-Voltage before Boosting

·

VH-Voltage after Boosting

·

Boost Ratio



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON (READY).

4.

With the shift lever in D, depress both the accelerator pedal and brake pedal at the same time to raise the "Hybrid/EV Battery SOC" to a sufficient level.

5.

Move the shift lever to P, check that the engine is stopped and move the shift lever to N.

6.

Set the A/C for maximum cooling.

7.

Leave the vehicle for a few minutes.

HINT:

When the accelerator pedal is not depressed with the ignition switch ON (READY) and shift lever in P, if "VL-Voltage before Boosting" and the "Hybrid/EV Battery Voltage" is approximately the same after repair, the condition is judged as normal.


8.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

9.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL, MOTOR GENERATOR, HV BATTERY)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > Motor Generator > Trouble Codes
50001 395
Powertrain > HV Battery > Trouble Codes
50001 398
Result:
Result Proceed to
P1C2D62 and Microcomputer malfunction of Hybrid control system DTCs in the table below are output A
P1C2D62 and Microcomputer malfunction of Motor generator control system DTCs in the table below are output B
P1C2D62 and Microcomputer malfunction of Hybrid battery system DTCs in the table below are output C
P1C2D62 and Power source circuit malfunction of Motor generator control system DTCs in the table below are output D
P1C2D62 and Communication system malfunction of Hybrid control system DTCs in the table below are output E
P1C2D62 and Sensor and actuator circuit malfunction of Hybrid battery system DTCs in the table below are output F
P1C2D62 and System malfunction of Motor generator control system DTCs in the table below are output G
P0E311C, P0CA300 or P0B231C is output and DTCs other than the DTCs in the table below are output H
P1C2D62,P0E311C and P0CA300 are output I
P1C2D62 and P0B231 are output J
Only P1C2D62 is output K


Malfunction Content System Relevant DTC
Microcomputer malfunction Hybrid control system P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P0A1B49 Drive Motor "A" Control Module Internal Electronic Failure
P060B49 Hybrid/EV Powertrain Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message
Motor generator control system P0A1A47 Generator Control Module Watchdog / Safety MC Failure
P0A1A49 Generator Control Module Internal Electronic Failure
P0A1B1F Generator Control Module Circuit Intermittent
P1C2A1C Generator A/D Converter Circuit Circuit Voltage Out of Range
P1C2A49 Generator A/D Converter Circuit Internal Electronic Failure
P313383 Communication Error from Generator to Drive Motor "A" Value of Signal Protection Calculation Incorrect
P313386 Communication Error from Generator to Drive Motor "A" Signal Invalid
P313387 Communication Error from Generator to Drive Motor "A" Missing Message
Hybrid battery system P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Battery Energy Control Module Processor from Monitoring Processor Missing Message
P0E2D00 Hybrid/EV Battery Energy Control Module Hybrid/EV Battery Monitor Performance
Power source circuit malfunction Motor generator control system P06D61C Generator Control Module Offset Power Circuit Voltage Out of Range
Communication system malfunction Hybrid control system P312387 Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message
U011187 Lost Communication with Hybrid/EV Battery Energy Control Module "A" Missing Message
Sensor and actuator circuit malfunction Hybrid battery system P301A1C Hybrid Battery Stack 1 Cell Voltage Detection Voltage Out of Range
P1A001C Hybrid Battery Stack 2 Cell Voltage Detection Voltage Out of Range
P1AFD1C Flying Capacitor/Internal Control Module Hybrid/EV Battery Monitor Voltage Out of Range
System malfunction Motor generator control system P0E3116 DC/DC Converter Voltage Sensor "A" (VL) Circuit Voltage Below Threshold
P0E3117 DC/DC Converter Voltage Sensor "A" (VL) Circuit Voltage Above Threshold

HINT:
·

P1C2D62 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

B

C

D

E

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

F

G

H

2.CLEAR DTC

I

REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

J

K

2.CLEAR DTC
2.CLEAR DTC

NEXT

3.CHECK DTC OUTPUT (CHECK FAILURE PART)
3.CHECK DTC OUTPUT (CHECK FAILURE PART)

Pre-procedure1

a.

Apply the parking brake and secure the wheels using chocks.

NOTICE:

Perform this test with the AUTO function (shift-linked function) of the electronic parking brake system off.


HINT:

When the parking brake indicator (red) is illuminated after the electric parking brake switch (electric parking brake switch assembly) has been pulled to the lock side, the maximum amount of braking force is applied if the electric parking brake switch (electric parking brake switch assembly) is pulled to the lock side one more time.



b.

Turn the ignition switch to ON (READY). *1


c.

If the value of "Hybrid/EV Battery SOC" is less than 55%, move the shift lever to D and charge the HV battery by depressing the accelerator pedal and brake pedal simultaneously until the value reaches 55% or more. *2

Powertrain > Hybrid Control > Data List
Tester Display
Hybrid/EV Battery SOC
Hybrid/EV Battery Current
50003 397 320,228

d.

Move the shift lever to P. *3


e.

Set the air conditioning to MAX COOL and turn the headlights on. *4


f.

Confirm that "Hybrid/EV Battery Current" is more than 3 A. *5


g.

With the engine stopped and the conditions of steps *3, *4 and *5 satisfied, leave the vehicle for 15 seconds. *6


Procedure1

a.

Check for DTCs. *7

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > Motor Generator > Trouble Codes
50001 395
Powertrain > HV Battery > Trouble Codes
50001 398
NOTICE:

If the low HV battery information comes on, move the shift lever to P and start the engine to charge the HV battery. After the engine stops, perform steps *1 through *7 again.


Result:
Result Proceed to
DTCs are output A
No DTCs in the table below are output B
P0E311C or P0CA300 is output C
P0B231C or P1C8349 is output D
P300000 is output E


Malfunction Content System Relevant DTC
Sensor and actuator circuit malfunction Hybrid control system P0E311C Boosting Converter Voltage Sensor "A" Voltage Out of Range
P0B231C Hybrid/EV Battery "A" Voltage Sensor Voltage Out of Range
System malfunction Hybrid control system P1C8349 High Voltage Power Resource Circuit Voltage Sensor after Boosting Malfunction
Motor generator control system P0CA300 DC/DC Converter Step Up Voltage Performance
Hybrid battery system P300000 Hybrid/EV Battery Discharge Control Malfunction


Post-procedure1

a.

Turn the ignition switch off.



A

4.CHECK DTC OUTPUT (ROAD TEST)

B

4.CHECK DTC OUTPUT (ROAD TEST)

C

REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

D

E

LEAVE VEHICLE WITH SHIFT LEVER IN P, AND CHARGE HV BATTERY BY IDLING UNTIL IDLING STOPS (PERFORM STEPS *1 THROUGH *7)

4.CHECK DTC OUTPUT (ROAD TEST)

Pre-procedure1

a.

Turn the ignition switch to ON (READY). *8


b.

Perform a road test that repeats full acceleration to 60 km/h (37 mph) and then braking to a complete stop 3 times. *9

CAUTION:

Perform this road test only in an appropriate safe location, in accordance with all local laws.


HINT:

This road test is performed to drive the car under high load and cause a change in the HV battery voltage.



Procedure1

a.

Check for DTCs. *10

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > Motor Generator > Trouble Codes
50001 395
Powertrain > HV Battery > Trouble Codes
50001 398
Result:
Result Proceed to
DTCs are output A
No DTCs in the table below are output B
P0E311C or P0CA300 is output C
P0B231C or P1C8349 is output D
P300000 is output E


Malfunction Content System Relevant DTC
Sensor and actuator circuit malfunction Hybrid control system P0E311C Boosting Converter Voltage Sensor "A" Voltage Out of Range
P0B231C Hybrid/EV Battery "A" Voltage Sensor Voltage Out of Range
System malfunction Hybrid control system P1C8349 High Voltage Power Resource Circuit Voltage Sensor after Boosting Malfunction
Motor generator control system P0CA300 DC/DC Converter Step Up Voltage Performance
Hybrid battery system P300000 Hybrid/EV Battery Discharge Control Malfunction


Post-procedure1

a.

Turn the ignition switch off.



A

5.READ VALUE USING GTS (DATA LIST)

B

5.READ VALUE USING GTS (DATA LIST)

C

REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

D

E

LEAVE VEHICLE WITH SHIFT LEVER IN P, AND CHARGE HV BATTERY BY IDLING UNTIL IDLING STOPS (PERFORM STEPS *8 THROUGH *10)

5.READ VALUE USING GTS (DATA LIST)

Pre-procedure1

a.

Apply the parking brake and secure the wheels using chocks.

NOTICE:

Perform this test with the AUTO function (shift-linked function) of the electronic parking brake system off.


HINT:

When the parking brake indicator (red) is illuminated after the electric parking brake switch (electric parking brake switch assembly) has been pulled to the lock side, the maximum amount of braking force is applied if the electric parking brake switch (electric parking brake switch assembly) is pulled to the lock side one more time.



b.

Turn the ignition switch to ON (READY).


Procedure1

a.

If the value of "Hybrid/EV Battery SOC" is less than 55%, move the shift lever to D and charge the HV battery by depressing the accelerator pedal and brake pedal simultaneously until the value reaches 55% or more.

Powertrain > Hybrid Control > Data List
Tester Display
VL-Voltage before Boosting
VH-Voltage after Boosting
Hybrid/EV Battery SOC
Hybrid/EV Battery Voltage
50003 397 150,151,320,227

b.

Release the accelerator pedal, move the shift lever to P and wait for the engine to stop. Read the Data List when the engine stops.

HINT:

If the engine starts, wait until it stops before continuing.


Result:
Result Proceed to
Both of the following are not satisfied. A
Both of the following are satisfied:
·

Difference between "Hybrid/EV Battery Voltage" and "VH-Voltage after Boosting" is less than 5 V.

·

Difference between "VL-Voltage before Boosting" and "VH-Voltage after Boosting" is more than 30 V.


B
Both of the following are satisfied:
·

Difference between "VH-Voltage after Boosting" and "VL-Voltage before Boosting" is less than 5 V.

·

Difference between "Hybrid/EV Battery Voltage" and "VH-Voltage after Boosting" is more than 15 V.


C



Post-procedure1

a.

Turn the ignition switch off.



A

6.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

B

REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

C

6.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

Pre-procedure1

a.

None.


Procedure1

a.

Read the freeze frame data of DTC P1C2D62.

Powertrain > Hybrid Control > DTC(P1C2D62) > Freeze Frame Data
Tester Display
VL-Voltage before Boosting
Hybrid/EV Battery Voltage
50040 397 150,227 P1C2D62
Result:
Result Proceed to
Both of the following are satisfied or both of the following are not satisfied. A
"VL-Voltage before Boosting" is less than 129 V or more than 201 V. B
"Hybrid/EV Battery Voltage" is less than 129 V or more than 201 V. C



Post-procedure1

a.

Turn the ignition switch off.



A

7.READ VALUE USING GTS (DATA LIST)

B

REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

C

7.READ VALUE USING GTS (DATA LIST)

Pre-procedure1

a.

Apply the parking brake and secure the wheels using chocks.

NOTICE:

Perform this test with the AUTO function (shift-linked function) of the electronic parking brake system off.


HINT:

When the parking brake indicator (red) is illuminated after the electric parking brake switch (electric parking brake switch assembly) has been pulled to the lock side, the maximum amount of braking force is applied if the electric parking brake switch (electric parking brake switch assembly) is pulled to the lock side one more time.



b.

Turn the ignition switch to ON (READY).


Procedure1

a.

If the value of "Hybrid/EV Battery SOC" is less than 55%, move the shift lever to D and charge the HV battery by depressing the accelerator pedal and brake pedal simultaneously until the value reaches 55% or more.


Powertrain > HV Battery > Data List
Tester Display
Hybrid/EV Battery SOC
Hybrid/EV Battery Voltage
Hybrid/EV Battery Cell 1 Voltage
Hybrid/EV Battery Cell 2 Voltage
Hybrid/EV Battery Cell 3 Voltage
Hybrid/EV Battery Cell 4 Voltage
Hybrid/EV Battery Cell 5 Voltage
Hybrid/EV Battery Cell 6 Voltage
Hybrid/EV Battery Cell 7 Voltage
Hybrid/EV Battery Cell 8 Voltage
Hybrid/EV Battery Cell 9 Voltage
Hybrid/EV Battery Cell 10 Voltage
Hybrid/EV Battery Cell 11 Voltage
Hybrid/EV Battery Cell 12 Voltage
Hybrid/EV Battery Cell 13 Voltage
Hybrid/EV Battery Cell 14 Voltage
Hybrid/EV Battery Cell 15 Voltage
Hybrid/EV Battery Cell 16 Voltage
Hybrid/EV Battery Cell 17 Voltage
Hybrid/EV Battery Cell 18 Voltage
Hybrid/EV Battery Cell 19 Voltage
Hybrid/EV Battery Cell 20 Voltage
Hybrid/EV Battery Cell 21 Voltage
Hybrid/EV Battery Cell 22 Voltage
Hybrid/EV Battery Cell 23 Voltage
Hybrid/EV Battery Cell 24 Voltage
Hybrid/EV Battery Cell 25 Voltage
Hybrid/EV Battery Cell 26 Voltage
Hybrid/EV Battery Cell 27 Voltage
Hybrid/EV Battery Cell 28 Voltage
Hybrid/EV Battery Cell 29 Voltage
Hybrid/EV Battery Cell 30 Voltage
Hybrid/EV Battery Cell 31 Voltage
Hybrid/EV Battery Cell 32 Voltage
Hybrid/EV Battery Cell 33 Voltage
Hybrid/EV Battery Cell 34 Voltage
Hybrid/EV Battery Cell 35 Voltage
Hybrid/EV Battery Cell 36 Voltage
Hybrid/EV Battery Cell 37 Voltage
Hybrid/EV Battery Cell 38 Voltage
Hybrid/EV Battery Cell 39 Voltage
Hybrid/EV Battery Cell 40 Voltage
Hybrid/EV Battery Cell 41 Voltage
Hybrid/EV Battery Cell 42 Voltage
Hybrid/EV Battery Cell 43 Voltage
Hybrid/EV Battery Cell 44 Voltage
Hybrid/EV Battery Cell 45 Voltage
Hybrid/EV Battery Cell 46 Voltage
Hybrid/EV Battery Cell 47 Voltage
Hybrid/EV Battery Cell 48 Voltage
50003 398 297,288,334,335,336,337,338,339,340,341,342,343,344,345,346,347,348,349,350,351,352,353,354,355,356,357,358,359,360,361,362,363,364,365,366,367,368,369,370,371,372,373,374,375,376,377,378,379,380,381
b.

Release the accelerator pedal, move the shift lever to P and wait for the engine to stop. Read the Data List when the engine stops.

HINT:

If the engine starts, wait until it stops before continuing.


Result:
Result Proceed to
Both of the following are satisfied:
·

Sum of all "Hybrid/EV Battery Cell 1 to 48 Voltage" is more than ("Hybrid/EV Battery Voltage" - 10 V)

·

Sum of all "Hybrid/EV Battery Cell 1 to 48 Voltage" is less than ("Hybrid/EV Battery Voltage" + 10 V)


A
The preceding condition is not satisfied. B



Post-procedure1

a.

Turn the ignition switch off.



A

REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

B