| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 8 | REAR CENTER SEAT OUTER BELT ASSEMBLY | 73350C | - | - | - |
| 9 | BENCH TYPE REAR SEAT CUSHION ASSEMBLY | - | - | - | - |
| 10 | REAR SEAT CUSHION LOCK HOOK | 72693 | - | - | - |
| 11 | REAR DOOR SCUFF PLATE INSIDE LH | 67918F | - | - | - |
| 12 | REAR UNDER COVER | 76971G | - | - | - |
| 13 | REAR SEAT CUSHION LEG SUB-ASSEMBLY | 71033 | - | - | - |
| ● | Non-reusable part | - | - |
| *A | for 2WD | - | - |
| *A | for AWD | - | - |
| *A | for AWD | - | - |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during HV floor under wire removal/installation are shown below.
Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION
To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
G3834
2.REMOVE SERVICE PLUG GRIP
73350C
8.DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
9.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY
72693
10.REMOVE REAR SEAT CUSHION LOCK HOOK
67918F
11.REMOVE REAR DOOR SCUFF PLATE INSIDE LH
76971G
12.REMOVE REAR UNDER COVER
71033
13.REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY
G9230
15.REMOVE BATTERY COOLING BLOWER ASSEMBLY
57628E
16.REMOVE REAR FLOOR SIDE MEMBER COVER LH
64740C
17.REMOVE FRONT FLOOR COVER LH
|
Bolt |
|
Clip |
51201
18.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
821H1
19.REMOVE FLOOR UNDER WIRE (for 2WD)
|
|
| *a | Shield Ground | - | - |
Disconnect the 2 HV battery junction block assembly and floor wire connectors.
Disconnect the shield ground from the HV battery.
Remove the 2 nuts.
Remove the 3 nuts and clamp.
If the clamps are removed forcibly, the stud bolts may be damaged.
Disengage the grommet and pull out the HV floor under wire from the floor panel hole.
Disengage the 4 clamps.
Disconnect the HV floor under wire connector.
Remove the bolt, nut and HV floor under wire.
58410B
20.REMOVE DECK BOARD ASSEMBLY (for AWD)
64993
21.REMOVE REAR DECK FLOOR BOX (for AWD)
26.REMOVE REAR SEATBACK ASSEMBLY LH (for AWD)
58387B
27.REMOVE REAR FLOOR FINISH PLATE (for AWD)
64740C
28.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (for AWD)
821H1
30.REMOVE FLOOR UNDER WIRE (for AWD)
|
|
Remove the 2 nuts.
Remove the 3 nuts and clamp.
If the clamps are removed forcibly, the stud bolts may be damaged.
Disengage the grommet and pull out the HV floor under wire from the floor panel hole.
Disengage the 4 clamps.
Disconnect the HV floor under wire connector.
Remove the bolt, nut and HV floor under wire.
Disengage the 3 clamps.
| *a | Waterproof Seal | - | - |
Using an insulated tool, remove the 4 bolts and disconnect the HV floor under wire from the rear hybrid motor control inverter assembly.
Do not allow any foreign matter or water to enter the rear hybrid motor control inverter assembly.
Do not touch the waterproof seal or terminals of the HV floor under wire.
Do not damage the terminals, connector housing or rear hybrid motor control inverter assembly during disconnection.
Insulate the disconnected terminals with insulating tape.
821H3
31.REMOVE HV BATTERY PACK WIRE (for AWD)
|
|
| *a | Shield Ground | - | - |
Disconnect the 2 HV battery junction block assembly and floor wire connectors.
Disconnect the shield ground from the HV battery.
| *a | Interlock | *b | Waterproof Seal |
Using an insulated tool, remove the 4 bolts and disconnect the HV battery pack wire from the rear hybrid motor control inverter assembly.
Do not allow any foreign matter or water to enter the rear hybrid motor control inverter assembly.
Do not touch the waterproof seal or terminals of the rear traction motor cable.
Do not damage the terminals, connector housing or rear hybrid motor control inverter assembly during disconnection.
Insulate the disconnected terminals with insulating tape.
Make sure to pull the rear traction motor cable out, as a connector is connected to the inside of the inverter terminal cover.