Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441183 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P31B300  Hybrid/EV Battery Voltage High  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The hybrid vehicle control ECU assembly uses the inverter voltage to monitor the HV battery voltage and detect malfunctions.

The cause of this malfunction may be the following:

Hybrid motor control inverter assembly malfunction (Boost converter system)
·

VL sensor malfunction

·

VH sensor malfunction


HV battery system
·

Battery ECU assembly malfunction

·

HV battery malfunction



DESCRIPTION

The hybrid vehicle control ECU assembly uses the inverter voltage to monitor the HV battery voltage and detect malfunctions.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
P31B300 Hybrid/EV Battery Voltage High The inverter voltage exceeds the threshold.
(1 trip detection logic)
·

Hybrid motor control inverter assembly

·

Battery ECU assembly

·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly


Comes on Master Warning:
Comes on
Hybrid Control A

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON (READY) and wait for 30 seconds or more.

4.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for the HV battery high-voltage line circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>HV Battery High-voltage Line Circuit

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*

*: for AWD

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C44
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*.


*: for AWD

·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.

·
A358021C06
0.604,4.135 0.917,4.333 0.313,0.198 10 false *a 2.719,4.135 3.031,4.333 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

·

Before returning the HV battery, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION

·

Before returning the HV supply stack sub-assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery and HV supply stack sub-assemblies.

·
A358020

After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.



NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL, MOTOR GENERATOR)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > Motor Generator > Trouble Codes
50001 395
Result:
Result Proceed to
Only P31B300 for Hybrid control system is output A
P31B300 and DTCs other than the DTCs in the table below are output B
P31B300 and Sensor and actuator circuit malfunction of Hybrid control system DTCs in the table below are output C
P31B300 and Sensor and actuator circuit malfunction of Motor generator control system DTCs in the table below are output D


Malfunction Content System Relevant DTC
Sensor and actuator circuit malfunction Hybrid control system P0D2D1C Drive Motor "A" Inverter Voltage Sensor Voltage Out of Range
P0E311C Boosting Converter Voltage Sensor "A" Voltage Out of Range
P1C2D62 Hybrid/EV Battery "A" Voltage Sensor/Boosting Converter Voltage Sensor "A" Signal Compare Failure
Motor generator control system P0D2D16 Drive Motor "A" Inverter Voltage Sensor (VH) Circuit Voltage Below Threshold
P0D2D17 Drive Motor "A" Inverter Voltage Sensor (VH) Circuit Voltage Above Threshold
P0D2D1F Drive Motor "A" Inverter Voltage Sensor(VH) Circuit Intermittent
P0E3116 DC/DC Converter Voltage Sensor "A" (VL) Circuit Voltage Below Threshold
P0E3117 DC/DC Converter Voltage Sensor "A" (VL) Circuit Voltage Above Threshold
P0E311F DC/DC Converter Voltage Sensor "A"(VL) Circuit Intermittent
P0E5717 DC/DC Converter Voltage Sensor "A"(VL) Circuit Voltage Above Threshold

HINT:
·

P31B300 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

2.READ VALUE USING GTS (HYBRID BATTERY VOLTAGE)

B

2.READ VALUE USING GTS (HYBRID BATTERY VOLTAGE)

C

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

D

2.READ VALUE USING GTS (HYBRID BATTERY VOLTAGE)

Pre-procedure1

a.

None.


Procedure1

a.

Read the Data List.

NOTICE:

Be sure not to measure when the ignition switch is ON (READY).


Powertrain > HV Battery > Data List
Tester Display
Hybrid/EV Battery Voltage
50003 398 288

b.

Make a note of the data list item "Hybrid/EV Battery Voltage".

Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

3.CHECK HV BATTERY
3.CHECK HV BATTERY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the electric vehicle battery plug assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY PLUG>REMOVAL



c.
A459744N01
1.615,1.771 1.979,2.021 0.365,0.25 0.406,0.417 0.771,0.667 0.365,0.25 1.688,1.813 1.948,1.979 0.26,0.167 10 true z10 0.479,0.479 0.74,0.646 0.26,0.167 10 true z14

Disconnect the z10 and z14 HV supply stack sub-assembly connectors.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



Procedure1

a.
A407228C07
0.479,1.135 0.854,1.396 0.375,0.26 0.833,2.396 1.208,2.656 0.375,0.26 2.01,1.927 1.781,1.531 true 1.333,3.917 1.146,3.427 true 0.573,1.208 0.885,1.406 0.313,0.198 10 false z14 0.927,2.458 1.24,2.656 0.313,0.198 10 false z10 0.417,0.313 0.729,0.469 0.313,0.156 10 false *a 0.313,2.448 0.625,2.604 0.313,0.156 10 false *b 1.365,3.917 1.625,4.198 0.26,0.281 10 false + 2.042,1.896 2.302,2.177 0.26,0.281 10 false -
*a No. 2 HV Supply Stack Sub-assembly Connector
(Hybrid Battery Terminal Block Side)
*b No. 1 HV Supply Stack Sub-assembly Connector
(No. 1 Traction Battery Device Box Assembly Side)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition

Click Location & Routing(z10,z14)Location & Routing

Click Connector(z10)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assembly

Click Connector(z14)Body>other>Hybrid Battery Terminal Block , HV Supply Battery Assembly

z10-1 (+) - z14-1 (-) Ignition switch off


CAUTION:

Do not allow the probes of the electrical tester to contact each other during this inspection.



b.

Check the value in the data list "Hybrid/EV Battery Voltage" and the hybrid battery voltage value that was actually measured.

Result:
Result Proceed to
When the difference between "Hybrid/EV Battery Voltage" in the Data List and the measurement value of the HV battery voltage is 5 V or more A
Other than above B



Post-procedure1

a.

Reconnect the z10 and z14 HV supply stack sub-assembly connectors.


b.

Install the electric vehicle battery plug assembly.



A

4.REPLACE BATTERY ECU ASSEMBLY

B

5.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
4.REPLACE BATTERY ECU ASSEMBLY

NEXT

REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY AND NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

5.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

Pre-procedure1

a.

None.


Procedure1

a.

Read the freeze frame data of DTC P31B300.

Powertrain > Hybrid Control > DTC(P31B300) > Freeze Frame Data
Tester Display
Hybrid/EV Battery Voltage
50040 397 227 P31B300
Result:
Result Proceed to
The value of Hybrid/EV Battery Voltage is less than 216 V A
None of the above conditions are met B



Post-procedure1

a.

Turn the ignition switch off.



A

REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

B

6.REPLACE BATTERY ECU ASSEMBLY
6.REPLACE BATTERY ECU ASSEMBLY

NEXT

REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY AND NO. 2 HV SUPPLY STACK SUB-ASSEMBLY