Refer to the description for DTC P0A9B11.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A9B11
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate | DTC Output from | Priority |
|---|---|---|---|---|---|---|---|
| P0A9B1C | Hybrid/EV Battery Temperature Sensor "A" Voltage Out of Range | The performance of battery temperature sensor 0 is abnormal; the difference in output between it and other battery temperature sensors is excessively large.
(1 trip detection logic) |
·
No. 1 HV supply stack sub-assembly ·
No. 2 HV supply stack sub-assembly ·
Battery ECU assembly |
Comes on | Master Warning:
Comes on |
HV Battery | A |
| P0AC51C | Hybrid/EV Battery Temperature Sensor "B" Voltage Out of Range | The performance of battery temperature sensor 1 is abnormal; the difference in output between it and other battery temperature sensors is excessively large.
(1 trip detection logic) |
·
No. 1 HV supply stack sub-assembly ·
No. 2 HV supply stack sub-assembly ·
Battery ECU assembly |
Comes on | Master Warning:
Comes on |
HV Battery | A |
| P0ACA1C | Hybrid/EV Battery Temperature Sensor "C" Voltage Out of Range | The performance of battery temperature sensor 2 is abnormal; the difference in output between it and other battery temperature sensors is excessively large.
(1 trip detection logic) |
·
No. 1 HV supply stack sub-assembly ·
No. 2 HV supply stack sub-assembly ·
Battery ECU assembly |
Comes on | Master Warning:
Comes on |
HV Battery | A |
| P0AE81C | Hybrid/EV Battery Temperature Sensor "D" Voltage Out of Range | The performance of battery temperature sensor 3 is abnormal; the difference in output between it and other battery temperature sensors is excessively large.
(1 trip detection logic) |
·
No. 2 HV supply stack sub-assembly ·
Battery ECU assembly |
Comes on | Master Warning:
Comes on |
HV Battery | A |
| P0BC21C | Hybrid/EV Battery Temperature Sensor "E" Voltage Out of Range | The performance of battery temperature sensor 4 is abnormal; the difference in output between it and other battery temperature sensors is excessively large.
(1 trip detection logic) |
·
No. 2 HV supply stack sub-assembly ·
Battery ECU assembly |
Comes on | Master Warning:
Comes on |
HV Battery | A |
| P0C331C | Hybrid/EV Battery Temperature Sensor "F" Voltage Out of Range | The performance of battery temperature sensor 5 is abnormal; the difference in output between it and other battery temperature sensors is excessively large.
(1 trip detection logic) |
·
No. 2 HV supply stack sub-assembly ·
Battery ECU assembly |
Comes on | Master Warning:
Comes on |
HV Battery | A |
| DTC No. | Data List |
|---|---|
| P0A9B1C | Hybrid/EV Battery Temperature 1 to 6 |
| P0AC51C | |
| P0ACA1C | |
| P0AE81C | |
| P0BC21C | |
| P0C331C |
If the vehicle as is left as is for 24 hours, the value of "Hybrid/EV Battery Temperature" will be almost the same as the ambient temperature.
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>UTILITY
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 2 minutes or more.
Turn the ignition switch to ON and wait for 10 seconds or more.
Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
Refer to the wiring diagram for DTC P0A9B2A.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A9B2A
Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
Inspecting the high-voltage system
Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*
Disconnecting the low voltage connector of the HV battery
*: for AWD
To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.
After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
| *a | Without waiting for 10 minutes |
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*. The voltage should be 0 V before beginning work.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*.
*: for AWD
Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.
If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.
| *a | Dealer |
| *b | Battery Collection Agent |
When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.
Accidents such as electric shock may result if the HV battery is disposed of improperly or abandoned. Therefore, make sure to return all HV batteries through an authorized collection agent.
Before returning the HV battery, make sure to perform a recovery inspection.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION
Before returning the HV supply stack sub-assembly, make sure to perform a recovery inspection.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>RECOVERY INSPECTION
Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery and HV supply stack sub-assemblies.
After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.
After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the auxiliary battery
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Pre-procedure1
None.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| Only P0A9B1C, P0AC51C, P0ACA1C, P0AE81C, P0BC21C or P0C331C for Hybrid battery system is output | A |
| P0A9B1C, P0AC51C, P0ACA1C, P0AE81C, P0BC21C or P0C331C is output and DTCs other than the DTCs in the table below are output | B |
| P0A9B1C, P0AC51C, P0ACA1C, P0AE81C, P0BC21C or P0C331C is output and Hybrid battery system DTCs in the table below are output | C |
| P0A9B1C, P0AC51C, P0ACA1C, P0AE81C, P0BC21C or P0C331C is output and Hybrid control system DTCs in the table below are output | D |
| System | Relevant DTC | |
|---|---|---|
| Hybrid battery system | P060A47 | Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure |
| P060B49 | Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure | |
| P060687 | Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message | |
| Hybrid control system | P0A1F94 | Hybrid/EV Battery Energy Control Module Unexpected Operation |
Post-procedure1
Turn the ignition switch off.
A
B
C
D
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Check the DTCs that were output when the vehicle was brought to the workshop.
| Result | Proceed to |
|---|---|
| "P0A9B1C, P0AC51C or P0ACA1C" is also output. | A |
| "P0AE81C, P0BC21C or P0C331C" is also output. | B |
A
B
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A9B11
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A9B11
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves and protective goggles.
Pre-procedure1
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the No. 1 HV battery hose.
Disconnect the A No. 2 HV supply stack sub-assembly connector.
Before disconnecting the connector, check that it is not loose or disconnected.
Disconnect the z12 battery ECU assembly connector.
Before disconnecting the connector, check that it is not loose or disconnected.
Procedure1
| *a | Front view of wire harness connector
(to Battery ECU Assembly) |
| *b | Front view of wire harness connector
(to No. 1 HV Supply Stack Sub-assembly) |
Measure the resistance according to the value(s) in the tables below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(z12)Location & Routingewd_type=routing;type=c;code=z12 Click Connector(z12)Body>other>Battery ECU Assembly , HV Supply Battery Assemblyewd_type=component;type=c;code=z12;pinno=25,26,27,28,16,15 |
||
| z12-25 (TB0) - A-5 (TB0) | Ignition switch off | Below 1 Ω |
| z12-26 (GB0) - A-10 (GB0) | Ignition switch off | Below 1 Ω |
| z12-27 (TB1) - A-9 (TB1) | Ignition switch off | Below 1 Ω |
| z12-28 (GB1) - A-4 (GB1) | Ignition switch off | Below 1 Ω |
| z12-16 (TB2) - A-3 (TB2) | Ignition switch off | Below 1 Ω |
| z12-15 (GB2) - A-8 (GB2) | Ignition switch off | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(z12)Location & Routingewd_type=routing;type=c;code=z12 Click Connector(z12)Body>other>Battery ECU Assembly , HV Supply Battery Assemblyewd_type=component;type=c;code=z12;pinno=25,26,27,28,16,15 |
||
| z12-25 (TB0) or A-5 (TB0) - Body ground and other terminals | Ignition switch off | 10 kΩ or higher |
| z12-26 (GB0) or A-10 (GB0) - Body ground and other terminals | Ignition switch off | 10 kΩ or higher |
| z12-27 (TB1) or A-9 (TB1) - Body ground and other terminals | Ignition switch off | 10 kΩ or higher |
| z12-28 (GB1) or A-4 (GB1) - Body ground and other terminals | Ignition switch off | 10 kΩ or higher |
| z12-16 (TB2) or A-3 (TB2) - Body ground and other terminals | Ignition switch off | 10 kΩ or higher |
| z12-15 (GB2) or A-8 (GB2) - Body ground and other terminals | Ignition switch off | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the z12 battery ECU assembly connector.
Reconnect the A No. 2 HV supply stack sub-assembly connector.
Install the No. 1 HV battery hose.
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A9B11
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A9B11
| Proceed to |
|---|
| OK |
| NG |
OK
NG