Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441185 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0A9B11  Hybrid/EV Battery Temperature Sensor "A" Circuit Short to Ground  P0A9B15  Hybrid/EV Battery Temperature Sensor "A" Circuit Short to Auxiliary Battery or Open  P0AC511  Hybrid/EV Battery Temperature Sensor "B" Circuit Short to Ground  P0AC515  Hybrid/EV Battery Temperature Sensor "B" Circuit Short to Auxiliary Battery or Open  P0ACA11  Hybrid/EV Battery Temperature Sensor "C" Circuit Short to Ground  P0ACA15  Hybrid/EV Battery Temperature Sensor "C" Circuit Short to Auxiliary Battery or Open  P0AE811  Hybrid/EV Battery Temperature Sensor "D" Circuit Short to Ground  P0AE815  Hybrid/EV Battery Temperature Sensor "D" Circuit Short to Auxiliary Battery or Open  P0BC211  Hybrid/EV Battery Temperature Sensor "E" Circuit Short to Ground  P0BC215  Hybrid/EV Battery Temperature Sensor "E" Circuit Short to Auxiliary Battery or Open  P0C3311  Hybrid/EV Battery Temperature Sensor "F" Circuit Short to Ground  P0C3315  Hybrid/EV Battery Temperature Sensor "F" Circuit Short to Auxiliary Battery or Open  


DESCRIPTION

The battery temperature sensors are provided at 6 locations of the HV battery. The resistance of the thermistor, which is built into each battery temperature sensor, varies in accordance with changes in the HV battery temperature. The lower the battery temperature, the higher the thermistor resistance. Conversely, the higher the temperature, the lower the resistance. The battery ECU assembly uses the battery temperature sensors to detect the HV battery temperature. Based on the results of this detection, the battery ECU assembly controls the blower fan. (The blower fan starts when the HV battery temperature rises above a predetermined level.)

Temperature Sensor Identification Cross Reference Table:
DTC Title Sensor Battery Temperature Sensor GTS Display
A 0 1
B 1 2
C 2 3
D 3 4
E 4 5
F 5 6


HINT:

Use the reference table above to determine which battery temperature sensor corresponds to each DTC. For example, sensor A in the DTC title column is battery temperature sensor 0. This sensor is displayed as Hybrid/EV Battery Temperature 1 in the Data List.


A171806E05
1.896,0.031 2.635,0.188 0.74,0.156 10 false Reference: 2.167,0.354 2.427,0.5 0.26,0.146 10 false 250 2.167,0.677 2.427,0.823 0.26,0.146 10 false 200 2.167,0.979 2.427,1.125 0.26,0.146 10 false 150 2.177,1.271 2.438,1.417 0.26,0.146 10 false 100 2.25,1.583 2.438,1.729 0.188,0.146 10 false 50 2.333,1.896 2.438,2.042 0.104,0.146 10 false 0 3.271,2.25 3.375,2.396 0.104,0.146 10 false 0 2.573,2.25 2.802,2.417 0.229,0.167 10 false -40 2.917,2.25 3.146,2.417 0.229,0.167 10 false -20 3.521,2.25 3.698,2.417 0.177,0.167 10 false 20 3.813,2.25 3.99,2.417 0.177,0.167 10 false 40 4.094,2.25 4.271,2.417 0.177,0.167 10 false 60 4.396,2.25 4.573,2.417 0.177,0.167 10 false 80 4.646,2.25 4.906,2.417 0.26,0.167 10 false 100 3.177,2.458 3.448,2.604 0.271,0.146 10 false (32) 2.531,2.448 2.865,2.615 0.333,0.167 10 false (-40) 2.906,2.448 3.167,2.615 0.26,0.167 10 false (-4) 3.458,2.448 3.729,2.615 0.271,0.167 10 false (68) 3.708,2.448 4.073,2.615 0.365,0.167 10 false (104) 4.031,2.448 4.375,2.615 0.344,0.167 10 false (140) 4.354,2.448 4.708,2.615 0.354,0.167 10 false (176) 4.677,2.448 5.021,2.615 0.344,0.167 10 false (212) 5.094,2.24 5.365,2.438 0.271,0.198 10 false (°C) 5.094,2.448 5.427,2.646 0.333,0.198 10 false (°F) 1.823,0.375 2.115,0.573 0.292,0.198 10 false (kΩ) 1.24,1.146 1.969,1.333 0.729,0.188 10 false Resistance 5.531,2.24 6.875,2.427 1.344,0.188 10 false Battery Temperature 2.604,0.042 5.698,0.219 3.094,0.177 10 false Battery Temperature Sensor Characteristic Graph

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
P0A9B11 Hybrid/EV Battery Temperature Sensor "A" Circuit Short to Ground The battery temperature sensor is malfunctioning, its output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value.
(1 trip detection logic)
·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly

·

No. 1 traction battery device box assembly

·

Battery ECU assembly

·

Wire harness or connector


Comes on Master Warning:
Comes on
HV Battery A
P0A9B15 Hybrid/EV Battery Temperature Sensor "A" Circuit Short to Auxiliary Battery or Open The battery temperature sensor is malfunctioning, its output voltage is higher than the specified value (short to +B or open) and the detected temperature is lower than the specified value.
(1 trip detection logic)
·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly

·

No. 1 traction battery device box assembly

·

Battery ECU assembly

·

Wire harness or connector


Comes on Master Warning:
Comes on
HV Battery A
P0AC511 Hybrid/EV Battery Temperature Sensor "B" Circuit Short to Ground The battery temperature sensor is malfunctioning, its output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value.
(1 trip detection logic)
·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly

·

No. 1 traction battery device box assembly

·

Battery ECU assembly

·

Wire harness or connector


Comes on Master Warning:
Comes on
HV Battery A
P0AC515 Hybrid/EV Battery Temperature Sensor "B" Circuit Short to Auxiliary Battery or Open The battery temperature sensor is malfunctioning, its output voltage is higher than the specified value (short to +B or open) and the detected temperature is lower than the specified value.
(1 trip detection logic)
·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly

·

No. 1 traction battery device box assembly

·

Battery ECU assembly

·

Wire harness or connector


Comes on Master Warning:
Comes on
HV Battery A
P0ACA11 Hybrid/EV Battery Temperature Sensor "C" Circuit Short to Ground The battery temperature sensor is malfunctioning, its output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value.
(1 trip detection logic)
·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly

·

No. 1 traction battery device box assembly

·

Battery ECU assembly

·

Wire harness or connector


Comes on Master Warning:
Comes on
HV Battery A
P0ACA15 Hybrid/EV Battery Temperature Sensor "C" Circuit Short to Auxiliary Battery or Open The battery temperature sensor is malfunctioning, its output voltage is higher than the specified value (short to +B or open) and the detected temperature is lower than the specified value.
(1 trip detection logic)
·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly

·

No. 1 traction battery device box assembly

·

Battery ECU assembly

·

Wire harness or connector


Comes on Master Warning:
Comes on
HV Battery A
P0AE811 Hybrid/EV Battery Temperature Sensor "D" Circuit Short to Ground The battery temperature sensor is malfunctioning, its output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value.
(1 trip detection logic)
·

No. 2 HV supply stack sub-assembly

·

No. 1 traction battery device box assembly

·

Battery ECU assembly

·

Wire harness or connector


Comes on Master Warning:
Comes on
HV Battery A
P0AE815 Hybrid/EV Battery Temperature Sensor "D" Circuit Short to Auxiliary Battery or Open The battery temperature sensor is malfunctioning, its output voltage is higher than the specified value (short to +B or open) and the detected temperature is lower than the specified value.
(1 trip detection logic)
·

No. 2 HV supply stack sub-assembly

·

No. 1 traction battery device box assembly

·

Battery ECU assembly

·

Wire harness or connector


Comes on Master Warning:
Comes on
HV Battery A
P0BC211 Hybrid/EV Battery Temperature Sensor "E" Circuit Short to Ground The battery temperature sensor is malfunctioning, its output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value.
(1 trip detection logic)
·

No. 2 HV supply stack sub-assembly

·

No. 1 traction battery device box assembly

·

Battery ECU assembly

·

Wire harness or connector


Comes on Master Warning:
Comes on
HV Battery A
P0BC215 Hybrid/EV Battery Temperature Sensor "E" Circuit Short to Auxiliary Battery or Open The battery temperature sensor is malfunctioning, its output voltage is higher than the specified value (short to +B or open) and the detected temperature is lower than the specified value.
(1 trip detection logic)
·

No. 2 HV supply stack sub-assembly

·

No. 1 traction battery device box assembly

·

Battery ECU assembly

·

Wire harness or connector


Comes on Master Warning:
Comes on
HV Battery A
P0C3311 Hybrid/EV Battery Temperature Sensor "F" Circuit Short to Ground The battery temperature sensor is malfunctioning, its output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value.
(1 trip detection logic)
·

No. 2 HV supply stack sub-assembly

·

No. 1 traction battery device box assembly

·

Battery ECU assembly

·

Wire harness or connector


Comes on Master Warning:
Comes on
HV Battery A
P0C3315 Hybrid/EV Battery Temperature Sensor "F" Circuit Short to Auxiliary Battery or Open The battery temperature sensor is malfunctioning, its output voltage is higher than the specified value (short to +B or open) and the detected temperature is lower than the specified value.
(1 trip detection logic)
·

No. 2 HV supply stack sub-assembly

·

No. 1 traction battery device box assembly

·

Battery ECU assembly

·

Wire harness or connector


Comes on Master Warning:
Comes on
HV Battery A

Related Data List
DTC No. Data List
P0A9B11 Hybrid/EV Battery Temperature 1 to 6
P0A9B15
P0AC511
P0AC515
P0ACA11
P0ACA15
P0AE811
P0AE815
P0BC211
P0BC215
P0C3311
P0C3315

HINT:
·

After checking for the above DTCs, check the hybrid system Data List item "Hybrid/EV Battery Temperature" using the GTS.

Temperature Displayed Malfunction
Below -45°C (-49°F) Open or +B short circuit
95°C (203°F) or more GND short circuit

·

If the vehicle as is left as is for 24 hours, the value of "Hybrid/EV Battery Temperature" will be almost the same as the ambient temperature.



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON and wait for 10 seconds or more.

4.

Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A459466E02
0.656,2.563 3.479,2.917 2.823,0.354 10 false No. 1 Traction Battery Device Box Assembly 0.74,8.375 3.323,8.646 2.583,0.271 10 false No. 1 HV Supply Stack Sub-assembly 1.833,0.479 3.438,1 1.604,0.521 10 false Battery Current Sensor 4.958,8.458 6.99,8.729 2.031,0.271 10 false z12 Battery ECU Assembly 5.083,3.104 5.458,3.375 0.375,0.271 10 false 3 5.292,3.115 5.667,3.563 0.375,0.448 10 false TB3 5.292,3.521 5.667,3.76 0.375,0.24 10 false GB3 5.292,7.552 5.667,8 0.375,0.448 10 false TB2 5.281,7.969 5.656,8.417 0.375,0.448 10 false GB2 5.094,3.51 5.469,3.771 0.375,0.26 10 false 4 5.021,7.542 5.406,7.781 0.385,0.24 10 false 16 5.042,7.969 5.417,8.219 0.375,0.25 10 false 15 5.302,1.021 5.677,1.469 0.375,0.448 10 false VIB 5.292,1.375 5.667,1.823 0.375,0.448 10 false IB0 5.292,1.75 5.667,2.198 0.375,0.448 10 false IB1 5.281,2.094 5.656,2.542 0.375,0.448 10 false GIB 5.021,1.021 5.396,1.469 0.375,0.448 10 false 31 5.021,1.375 5.396,1.823 0.375,0.448 10 false 19 5.083,2.083 5.458,2.531 0.375,0.448 10 false 7 5.094,1.75 5.469,2.198 0.375,0.448 10 false 8 1.594,3.385 3.844,4.031 2.25,0.646 10 false Battery Temperature Sensor 3 5.281,3.844 5.667,4.031 0.385,0.188 10 false TB4 5.281,4.26 5.646,4.469 0.365,0.208 10 false GB4 5.292,4.677 5.667,4.875 0.375,0.198 10 false TB5 5.292,5.094 5.667,5.292 0.375,0.198 10 false GB5 5.292,6.01 5.667,6.458 0.375,0.448 10 false TB0 5.292,6.417 5.667,6.865 0.375,0.448 10 false GB0 5.292,6.813 5.667,7.26 0.375,0.448 10 false TB1 5.292,7.229 5.667,7.677 0.375,0.448 10 false GB1 5.021,3.833 5.396,4.104 0.375,0.271 10 false 29 5.021,4.24 5.396,4.479 0.375,0.24 10 false 30 5.01,4.677 5.385,5.125 0.375,0.448 10 false 18 5.031,5.094 5.385,5.375 0.354,0.281 10 false 17 5.031,6.01 5.396,6.271 0.365,0.26 10 false 25 5.031,6.438 5.323,6.667 0.292,0.229 10 false 26 5.031,6.813 5.417,7.042 0.385,0.229 10 false 27 5.031,7.229 5.406,7.479 0.375,0.25 10 false 28 1.594,4.115 3.844,4.76 2.25,0.646 10 false Battery Temperature Sensor 4 1.594,4.948 3.844,5.594 2.25,0.646 10 false Battery Temperature Sensor 5 1.604,6.302 3.854,6.948 2.25,0.646 10 false Battery Temperature Sensor 0 1.604,7.115 3.854,7.76 2.25,0.646 10 false Battery Temperature Sensor 1 1.615,7.865 3.865,8.51 2.25,0.646 10 false Battery Temperature Sensor 2 3.115,1.01 3.49,1.458 0.375,0.448 10 false VIB 3.135,1.375 3.51,1.823 0.375,0.448 10 false IB0 3.135,1.75 3.51,2.198 0.375,0.448 10 false IB1 3.104,2.083 3.479,2.531 0.375,0.448 10 false GIB 3.49,1.01 3.865,1.458 0.375,0.448 10 false 1 3.5,1.75 3.875,2.198 0.375,0.448 10 false 2 3.5,1.375 3.875,1.823 0.375,0.448 10 false 4 3.5,2.083 3.875,2.531 0.375,0.448 10 false 3 1.24,5.688 3.823,5.958 2.583,0.271 10 false No. 2 HV Supply Stack Sub-assembly 4.156,6.01 4.563,6.229 0.406,0.219 10 false 5 3.781,6.01 4.156,6.25 0.375,0.24 10 false 5 4.146,6.427 4.521,6.667 0.375,0.24 10 false 10 3.719,6.427 4.135,6.656 0.417,0.229 10 false 10 4.177,6.813 4.552,7.26 0.375,0.448 10 false 9 3.781,6.813 4.156,7.26 0.375,0.448 10 false 9 4.177,7.229 4.552,7.677 0.375,0.448 10 false 4 3.781,7.229 4.156,7.677 0.375,0.448 10 false 4 4.177,7.563 4.552,8.01 0.375,0.448 10 false 3 3.781,7.563 4.167,7.833 0.385,0.271 10 false 3 4.188,7.969 4.563,8.417 0.375,0.448 10 false 8 3.781,7.969 4.156,8.417 0.375,0.448 10 false 8 3.99,8.354 4.365,8.615 0.375,0.26 10 false A 0.313,2.573 0.771,2.771 0.458,0.198 10 false z11

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*

-

Disconnecting the low voltage connector of the HV battery


*: for AWD


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*.


*: for AWD


·
A358021C02
0.531,4.146 0.844,4.344 0.313,0.198 10 false *a 2.74,4.146 3.052,4.344 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

-

Accidents such as electric shock may result if the HV battery is disposed of improperly or abandoned. Therefore, make sure to return all HV batteries through an authorized collection agent.


·

Before returning the HV battery, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION

·

Before returning the HV supply stack sub-assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>RECOVERY INSPECTION

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery and HV supply stack sub-assemblies.

·
A358020

After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.

·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK DTC OUTPUT (HV BATTERY, HYBRID CONTROL)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > HV Battery > Trouble Codes
50001 398
Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
Only P0A9B11, P0A9B15, P0AC511, P0AC515, P0ACA11, P0ACA15, P0AE811, P0AE815, P0BC211, P0BC215, P0C3311 or P0C3315 for Hybrid battery system is output A
P0A9B11, P0A9B15, P0AC511, P0AC515, P0ACA11, P0ACA15, P0AE811, P0AE815, P0BC211, P0BC215, P0C3311 or P0C3315 is output and DTCs other than the DTCs in the table below are output B
P0A9B11, P0A9B15, P0AC511, P0AC515, P0ACA11, P0ACA15, P0AE811, P0AE815, P0BC211, P0BC215, P0C3311 or P0C3315 is output and Hybrid battery system DTCs in the table below are output C
P0A9B11, P0A9B15, P0AC511, P0AC515, P0ACA11, P0ACA15, P0AE811, P0AE815, P0BC211, P0BC215, P0C3311 or P0C3315 is output and Hybrid control system DTCs in the table below are output D


System Relevant DTC
Hybrid battery system P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
Hybrid control system P0A1F94 Hybrid/EV Battery Energy Control Module Unexpected Operation


Post-procedure1

a.

Turn the ignition switch off.



A

2.READ VALUE USING GTS (HYBRID/EV BATTERY TEMPERATURE)

B

2.READ VALUE USING GTS (HYBRID/EV BATTERY TEMPERATURE)

C

GO TO DTC CHART (HYBRID BATTERY SYSTEM)

D

2.READ VALUE USING GTS (HYBRID/EV BATTERY TEMPERATURE)

Pre-procedure1

a.

None.


Procedure1

a.

Read the Data List.

Powertrain > HV Battery > Data List
Tester Display Measurement Item Range Reference Value Diagnostic Note
Hybrid/EV Battery Temperature 1 HV battery temperature sensor output. -50 to 205.9°C (-58 to 402.6°F) Same as ambient temperature (left as is for 24 hours)
·

Battery temperature sensor

·

Battery ECU assembly


Hybrid/EV Battery Temperature 2 HV battery temperature sensor output. -50 to 205.9°C (-58 to 402.6°F) Same as ambient temperature (left as is for 24 hours)
·

Battery temperature sensor

·

Battery ECU assembly


Hybrid/EV Battery Temperature 3 HV battery temperature sensor output. -50 to 205.9°C (-58 to 402.6°F) Same as ambient temperature (left as is for 24 hours)
·

Battery temperature sensor

·

Battery ECU assembly


Hybrid/EV Battery Temperature 4 HV battery temperature sensor output. -50 to 205.9°C (-58 to 402.6°F) Same as ambient temperature (left as is for 24 hours)
·

Battery temperature sensor

·

Battery ECU assembly


Hybrid/EV Battery Temperature 5 HV battery temperature sensor output. -50 to 205.9°C (-58 to 402.6°F) Same as ambient temperature (left as is for 24 hours)
·

Battery temperature sensor

·

Battery ECU assembly


Hybrid/EV Battery Temperature 6 HV battery temperature sensor output. -50 to 205.9°C (-58 to 402.6°F) Same as ambient temperature (left as is for 24 hours)
·

Battery temperature sensor

·

Battery ECU assembly


Powertrain > HV Battery > Data List
Tester Display
Hybrid/EV Battery Temperature 1
Hybrid/EV Battery Temperature 2
Hybrid/EV Battery Temperature 3
Hybrid/EV Battery Temperature 4
Hybrid/EV Battery Temperature 5
Hybrid/EV Battery Temperature 6
50003 398 62,63,64,65,66,67
Result:
Proceed to
NEXT



HINT:

A malfunctioning sensor (battery temperature sensor 0 to 5) can be determined by comparing the output temperature of the 6 battery temperature sensors.


Post-procedure1

a.

Turn the ignition switch off.



NEXT

3.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY)
3.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery hose.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



Procedure1

a.
A458604N01
0.938,0.229 1.313,0.448 0.375,0.219 0.979,0.24 1.281,0.417 0.302,0.177 10 true z12

Check the connector connections and contact pressure of the relevant terminals for the battery ECU assembly.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

The connectors are connected securely and there are no contact pressure problems.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the No. 1 HV battery hose.



OK

4.CHECK DTC

NG

CONNECT SECURELY

4.CHECK DTC
a.

Check the DTCs that were output when the vehicle was brought to the workshop.


Result:
Result Proceed to
"P0A9B11, P0A9B15, P0AC511, P0AC515, P0ACA11 or P0ACA15" is also output. A
"P0AE811, P0AE815, P0BC211, P0BC215, P0C3311 or P0C3315" is also output. B



A

5.CHECK HV BATTERY (BATTERY TEMPERATURE SENSOR 0 to 2)

B

8.CHECK HV BATTERY (BATTERY TEMPERATURE SENSOR 3 to 5)
5.CHECK HV BATTERY (BATTERY TEMPERATURE SENSOR 0 to 2)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery hose.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



c.
A458604N01
0.938,0.229 1.313,0.448 0.375,0.219 0.979,0.24 1.281,0.417 0.302,0.177 10 true z12

Disconnect the z12 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



Procedure1

a.
A459571C03
1.49,0.115 1.948,0.427 0.458,0.313 0.802,2.844 1.146,2.219 true 1.073,3.021 1.25,2.219 true 1.396,2.854 1.365,2.219 true 1.698,3.042 1.469,2.208 true 2.031,2.875 1.479,2.094 true 1.344,2.063 0.438,2.24 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.615,0.198 2.073,0.396 0.458,0.198 10 false z12 0.958,3.083 1.323,3.281 0.365,0.198 10 false GB0 0.635,2.917 1.073,3.115 0.438,0.198 10 false TB0 1.25,2.917 1.688,3.115 0.438,0.198 10 false TB1 1.573,3.083 1.938,3.281 0.365,0.198 10 false GB1 1.906,2.917 2.344,3.115 0.438,0.198 10 false TB2 0.167,2.188 0.531,2.385 0.365,0.198 10 false GB2
*a Front view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance of the circuit for the malfunctioning sensor (battery temperature sensor 0 to 2).

Tester Connection:
Tester Connection Battery Temperature Sensor

Click Location & Routing(z12)Location & Routing

Click Connector(z12)Body>other>Battery ECU Assembly , HV Supply Battery Assembly

z12-25 (TB0) - z12-26 (GB0) 0
z12-27 (TB1) - z12-28 (GB1) 1
z12-16 (TB2) - z12-15 (GB2) 2


Standard Resistance:
Thermistor Temperature Condition Specified Condition
0 to 10°C (32 to 50°F) Ignition switch off 17.7 to 27.8 kΩ
10 to 20°C (50 to 68°F) Ignition switch off 12.0 to 18.2 kΩ
20 to 30°C (68 to 86°F) Ignition switch off 8.22 to 12.2 kΩ
30 to 40°C (86 to 104°F) Ignition switch off 5.74 to 8.41 kΩ
40 to 50°C (104 to 122°F) Ignition switch off 4.09 to 5.91 kΩ


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the z12 battery ECU assembly connector.


b.

Install the No. 1 HV battery hose.



OK

6.CHECK HV BATTERY (BATTERY TEMPERATURE SENSOR 0 to 2)

NG

7.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 2 HV SUPPLY STACK SUB-ASSEMBLY)
6.CHECK HV BATTERY (BATTERY TEMPERATURE SENSOR 0 to 2)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery hose.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



c.
A458604N01
0.938,0.229 1.313,0.448 0.375,0.219 0.979,0.24 1.281,0.417 0.302,0.177 10 true z12

Disconnect the z12 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



Procedure1

a.
A459571C03
1.49,0.115 1.948,0.427 0.458,0.313 0.802,2.844 1.146,2.219 true 1.073,3.021 1.25,2.219 true 1.396,2.854 1.365,2.219 true 1.698,3.042 1.469,2.208 true 2.031,2.875 1.479,2.094 true 1.344,2.063 0.438,2.24 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.615,0.198 2.073,0.396 0.458,0.198 10 false z12 0.958,3.083 1.323,3.281 0.365,0.198 10 false GB0 0.635,2.917 1.073,3.115 0.438,0.198 10 false TB0 1.25,2.917 1.688,3.115 0.438,0.198 10 false TB1 1.573,3.083 1.938,3.281 0.365,0.198 10 false GB1 1.906,2.917 2.344,3.115 0.438,0.198 10 false TB2 0.167,2.188 0.531,2.385 0.365,0.198 10 false GB2
*a Front view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance according to the value (s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z12)Location & Routing

Click Connector(z12)Body>other>Battery ECU Assembly , HV Supply Battery Assembly

z12-25 (TB0) - Body ground and other terminals (except z12-26 (GB0)) Ignition switch off 10 kΩ or higher
z12-26 (GB0) - Body ground and other terminals (except z12-25 (TB0)) Ignition switch off 10 kΩ or higher
z12-27 (TB1) - Body ground and other terminals (except z12-28 (GB1)) Ignition switch off 10 kΩ or higher
z12-28 (GB1) - Body ground and other terminals (except z12-27 (TB1)) Ignition switch off 10 kΩ or higher
z12-16 (TB2) - Body ground and other terminals (except z12-15 (GB2)) Ignition switch off 10 kΩ or higher
z12-15 (GB2) - Body ground and other terminals (except z12-16 (TB2)) Ignition switch off 10 kΩ or higher



b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value (s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(z12)Location & Routing

Click Connector(z12)Body>other>Battery ECU Assembly , HV Supply Battery Assembly

z12-25 (TB0) - Body ground Ignition switch ON Below 1 V
z12-26 (GB0) - Body ground Ignition switch ON Below 1 V
z12-27 (TB1) - Body ground Ignition switch ON Below 1 V
z12-28 (GB1) - Body ground Ignition switch ON Below 1 V
z12-16 (TB2) - Body ground Ignition switch ON Below 1 V
z12-15 (GB2) - Body ground Ignition switch ON Below 1 V


NOTICE:
·

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the ignition switch is turned to ON with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.



Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Reconnect the z12 battery ECU assembly connector.


d.

Install the No. 1 HV battery hose.



OK

10.CHECK BATTERY ECU ASSEMBLY (VIB VOLTAGE)

NG

7.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 2 HV SUPPLY STACK SUB-ASSEMBLY)
7.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 2 HV SUPPLY STACK SUB-ASSEMBLY)

OK

REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY

NG

REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

8.CHECK HV BATTERY (BATTERY TEMPERATURE SENSOR 3 to 5)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery hose.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



c.
A458604N01
0.938,0.229 1.313,0.448 0.375,0.219 0.979,0.24 1.281,0.417 0.302,0.177 10 true z12

Disconnect the z12 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



Procedure1

a.
A459571C04
1.49,0.115 1.948,0.427 0.458,0.313 1.552,2.104 1.063,3.031 true 1.563,2.208 1.385,2.875 true 1.667,2.208 1.698,3.031 true 1.677,2.115 2,2.885 true 1.354,2 0.292,2.854 true 1.458,2.01 0.781,2.865 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.615,0.198 2.073,0.396 0.458,0.198 10 false z12 0.917,3.083 1.281,3.281 0.365,0.198 10 false GB5 0.635,2.917 1.073,3.115 0.438,0.198 10 false GB3 1.25,2.917 1.688,3.115 0.438,0.198 10 false TB4 1.573,3.083 1.938,3.281 0.365,0.198 10 false GB4 1.906,2.917 2.344,3.115 0.438,0.198 10 false TB5 0.146,2.896 0.51,3.094 0.365,0.198 10 false TB3
*a Front view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance of the circuit for the malfunctioning sensor (battery temperature sensor 3 to 5).

Tester Connection:
Tester Connection Battery Temperature Sensor

Click Location & Routing(z12)Location & Routing

Click Connector(z12)Body>other>Battery ECU Assembly , HV Supply Battery Assembly

z12-3 (TB3) - z12-4 (GB3) 3
z12-29 (TB4) - z12-30 (GB4) 4
z12-18 (TB5) - z12-17 (GB5) 5


Standard Resistance:
Thermistor Temperature Condition Specified Condition
0 to 10°C (32 to 50°F) Ignition switch off 17.7 to 27.8 kΩ
10 to 20°C (50 to 68°F) Ignition switch off 12.0 to 18.2 kΩ
20 to 30°C (68 to 86°F) Ignition switch off 8.22 to 12.2 kΩ
30 to 40°C (86 to 104°F) Ignition switch off 5.74 to 8.41 kΩ
40 to 50°C (104 to 122°F) Ignition switch off 4.09 to 5.91 kΩ


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the z12 battery ECU assembly connector.


b.

Install the No. 1 HV battery hose.



OK

9.CHECK HV BATTERY (BATTERY TEMPERATURE SENSOR 3 to 5)

NG

REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

9.CHECK HV BATTERY (BATTERY TEMPERATURE SENSOR 3 to 5)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery hose.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



c.
A458604N01
0.938,0.229 1.313,0.448 0.375,0.219 0.979,0.24 1.281,0.417 0.302,0.177 10 true z12

Disconnect the z12 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



Procedure1

a.
A459571C04
1.49,0.115 1.948,0.427 0.458,0.313 1.552,2.104 1.063,3.031 true 1.563,2.208 1.385,2.875 true 1.667,2.208 1.698,3.031 true 1.677,2.115 2,2.885 true 1.354,2 0.292,2.854 true 1.458,2.01 0.781,2.865 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.615,0.198 2.073,0.396 0.458,0.198 10 false z12 0.917,3.083 1.281,3.281 0.365,0.198 10 false GB5 0.635,2.917 1.073,3.115 0.438,0.198 10 false GB3 1.25,2.917 1.688,3.115 0.438,0.198 10 false TB4 1.573,3.083 1.938,3.281 0.365,0.198 10 false GB4 1.906,2.917 2.344,3.115 0.438,0.198 10 false TB5 0.146,2.896 0.51,3.094 0.365,0.198 10 false TB3
*a Front view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance according to the value (s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z12)Location & Routing

Click Connector(z12)Body>other>Battery ECU Assembly , HV Supply Battery Assembly

z12-3 (TB3) - Body ground and other terminals (except z12-4 (GB3)) Ignition switch off 10 kΩ or higher
z12-4 (GB3) - Body ground and other terminals (except z12-3 (TB3)) Ignition switch off 10 kΩ or higher
z12-29 (TB4) - Body ground and other terminals (except z12-30 (GB4)) Ignition switch off 10 kΩ or higher
z12-30 (GB4) - Body ground and other terminals (except z12-29 (TB4)) Ignition switch off 10 kΩ or higher
z12-18 (TB5) - Body ground and other terminals (except z12-17 (GB5)) Ignition switch off 10 kΩ or higher
z12-17 (GB5) - Body ground and other terminals (except z12-18 (TB5)) Ignition switch off 10 kΩ or higher



b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value (s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(z12)Location & Routing

Click Connector(z12)Body>other>Battery ECU Assembly , HV Supply Battery Assembly

z12-3 (TB3) - Body ground Ignition switch ON Below 1 V
z12-4 (GB3) - Body ground Ignition switch ON Below 1 V
z12-29 (TB4) - Body ground Ignition switch ON Below 1 V
z12-30 (GB4) - Body ground Ignition switch ON Below 1 V
z12-18 (TB5) - Body ground Ignition switch ON Below 1 V
z12-17 (GB5) - Body ground Ignition switch ON Below 1 V


NOTICE:
·

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the ignition switch is turned to ON with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.



Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Reconnect the z12 battery ECU assembly connector.


d.

Install the No. 1 HV battery hose.



OK

10.CHECK BATTERY ECU ASSEMBLY (VIB VOLTAGE)

NG

REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

10.CHECK BATTERY ECU ASSEMBLY (VIB VOLTAGE)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON.


Procedure1

a.
A460457C01
0.281,3.271 0.708,3.635 0.427,0.365 1.885,3.438 2.302,3.021 true 1.896,3.667 2.323,4.042 true 1.01,2.438 1.323,2.635 0.313,0.198 10 false *a 0.385,3.375 0.844,3.573 0.458,0.198 10 false z11 2.365,2.938 2.823,3.135 0.458,0.198 10 false VIB 2.385,4.01 2.844,4.208 0.458,0.198 10 false GIB
*a Component with harness connected
(No. 1 Traction Battery Device Box Assembly (Battery Current Sensor))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(z11)Location & Routing

Click Connector(z11)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assembly

z11-1 (VIB) - z11-3 (GIB) Ignition switch ON 4.6 to 5.4 V


NOTICE:

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Install the HV battery upper cover panel.



OK

NG

11.CHECK NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE)
11.CHECK NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
A458502N01
0.719,1.135 1.073,1.365 0.354,0.229 0.74,1.156 1.031,1.333 0.292,0.177 10 true z11

Disconnect the z11 battery current sensor connector from the No. 1 traction battery device box assembly.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the ignition switch to ON.


Procedure1

a.
A459467C01
2.333,1.135 2.729,1.365 0.396,0.229 1.604,1.052 0.99,0.906 true 1,1.771 1.625,1.385 true 0.729,0.823 1.063,1.063 0.333,0.24 10 false VIB 0.729,1.719 1.094,1.969 0.365,0.25 10 false GIB 0.188,0.146 0.427,0.292 0.24,0.146 10 false *a 2.427,1.167 2.802,1.469 0.375,0.302 10 false z11
*a Front view of wire harness connector
(to No. 1 Traction Battery Device Box Assembly (Battery Current Sensor))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(z11)Location & Routing

Click Connector(z11)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assembly

z11-1 (VIB) - z11-3 (GIB) Ignition switch ON 4.6 to 5.4 V


NOTICE:
·

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the ignition switch is turned to ON with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.



Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Reconnect the z11 battery current sensor connector to the No. 1 traction battery device box assembly.


d.

Install the HV battery upper cover panel.



OK

REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

NG

REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY