A battery current sensor, which is mounted on the positive cable side of each HV battery junction block assembly, detects the current flowing to or from the battery pack. The battery current sensor sends a voltage, which varies between 0 and 5 V in proportion to the amperage, to the IB0 terminal of the battery ECU assembly. Similarly, it sends a voltage, which varies between 0 and 5 V in inverse proportion to the amperage, to the IB1 terminal of the battery ECU assembly. When the voltage at the IB0 terminal is below 2.57 V and the voltage at the IB1 terminal is above 2.43 V, this indicates that the HV battery is being discharged. Additionally, Meanwhile, when the voltage at of the IB0 terminal is above 2.57 V and the voltage at of the IB1 terminal is below 2.43 V, this indicates that the HV battery is being charged. The battery ECU assembly determines the charging and discharging amount of the HV battery based on the voltages input to the IB0 terminal and IB1 terminal and calculates the SOC of the HV battery through the accumulated amperage.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate | DTC Output from | Priority |
|---|---|---|---|---|---|---|---|
| P0ABF11 | Hybrid/EV Battery Current Sensor "A" Circuit Short to Ground | The battery current sensor output voltage (IB0) is excessively low.
(1 trip detection logic) |
·
No. 1 traction battery device box assembly ·
Battery ECU assembly ·
Wire harness or connector ·
No. 2 HV supply stack sub-assembly |
Comes on | Master Warning:
Comes on |
HV Battery | A |
| P0ABF15 | Hybrid/EV Battery Current Sensor "A" Circuit Short to Auxiliary Battery or Open | The battery current sensor output voltage (IB0) is excessively high.
(1 trip detection logic) |
·
No. 1 traction battery device box assembly ·
Battery ECU assembly ·
Wire harness or connector ·
No. 2 HV supply stack sub-assembly |
Comes on | Master Warning:
Comes on |
HV Battery | A |
| P0B0E11 | Hybrid/EV Battery Current Sensor "B" Circuit Short to Ground | The battery current sensor output voltage (IB1) is excessively low.
(1 trip detection logic) |
·
No. 1 traction battery device box assembly ·
Battery ECU assembly ·
Wire harness or connector ·
No. 2 HV supply stack sub-assembly |
Comes on | Master Warning:
Comes on |
HV Battery | A |
| P0B0E15 | Hybrid/EV Battery Current Sensor "B" Circuit Short to Auxiliary Battery or Open | The battery current sensor output voltage (IB1) is excessively high.
(1 trip detection logic) |
·
No. 1 traction battery device box assembly ·
Battery ECU assembly ·
Wire harness or connector ·
No. 2 HV supply stack sub-assembly |
Comes on | Master Warning:
Comes on |
HV Battery | A |
| P1CBB12 | Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Auxiliary Battery | Power source voltage (VIB) of the battery current sensor is excessively high.
(1 trip detection logic) |
·
No. 1 traction battery device box assembly ·
Battery ECU assembly ·
Wire harness or connector ·
No. 2 HV supply stack sub-assembly |
Comes on | Master Warning:
Comes on |
HV Battery | A |
| P1CBB14 | Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Ground or Open | Power source voltage (VIB) of the battery current sensor is excessively low.
(1 trip detection logic) |
·
No. 1 traction battery device box assembly ·
Battery ECU assembly ·
Wire harness or connector ·
No. 2 HV supply stack sub-assembly |
Comes on | Master Warning:
Comes on |
HV Battery | A |
| DTC No. | Data List |
|---|---|
| P0ABF11 | Hybrid/EV Battery Current |
| P0ABF15 | |
| P0B0E11 | |
| P0B0E15 | |
| P1CBB12 | |
| P1CBB14 |
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>UTILITY
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 2 minutes or more.
Turn the ignition switch to ON and wait for 5 seconds or more.
Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
Inspecting the high-voltage system
Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*
Disconnecting the low voltage connector of the HV battery
*: for AWD
To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.
After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
| *a | Without waiting for 10 minutes |
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*. The voltage should be 0 V before beginning work.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*.
*: for AWD
Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.
If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.
| *a | Dealer |
| *b | Battery Collection Agent |
When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.
Accidents such as electric shock may result if the HV battery is disposed of improperly or abandoned. Therefore, make sure to return all HV batteries through an authorized collection agent.
Before returning the HV battery, make sure to perform a recovery inspection.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION
Before returning the HV supply stack sub-assembly, make sure to perform a recovery inspection.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>RECOVERY INSPECTION
Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery and HV supply stack sub-assemblies.
After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.
After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the auxiliary battery
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Pre-procedure1
None.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| Only P0ABF11, P0ABF15, P0B0E11, P0B0E15, P1CBB12 or P1CBB14 for Hybrid battery system is output | A |
| P0ABF11, P0ABF15, P0B0E11, P0B0E15, P1CBB12 or P1CBB14 is output and DTCs other than the DTCs in the table below are output | B |
| P0ABF11, P0ABF15, P0B0E11, P0B0E15, P1CBB12 or P1CBB14 is output and Hybrid battery system DTCs in the table below are output | C |
| P0ABF11, P0ABF15, P0B0E11, P0B0E15, P1CBB12 or P1CBB14 is output and Hybrid control system DTCs in the table below are output | D |
| System | Relevant DTC | |
|---|---|---|
| Hybrid battery system | P060A47 | Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure |
| P060B49 | Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure | |
| P060687 | Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message | |
| Hybrid control system | P0A1F94 | Hybrid/EV Battery Energy Control Module Unexpected Operation |
Post-procedure1
Turn the ignition switch off.
A
B
C
D
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Be sure to wear insulated gloves and protective goggles.
Pre-procedure1
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the No. 1 HV battery hose.
Connect the cable to the negative (-) auxiliary battery terminal.
Disconnect the z12 battery ECU assembly connector.
Turn the ignition switch to ON.
Procedure1
| *a | Front view of wire harness connector
(to Battery ECU Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(z12)Location & Routingewd_type=routing;type=c;code=z12 Click Connector(z12)Body>other>Battery ECU Assembly , HV Supply Battery Assemblyewd_type=component;type=c;code=z12;pinno=24,34 |
||
| z12-24 (IGCT) - z12-34 (GND) | Ignition switch ON | 11 to 14 V |
Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.
As there might be an intermittent malfunction, inspect the following items even if the measured voltage is as specified.
Installation condition of fuse(s) (before removing fuse(s)) (IG circuit)
Fuse condition (before and after removing fuse(s)) (IG circuit)
Connection condition of connectors (IG circuit)
Wire harness condition (IG circuit)
Wire harness condition (GND circuit)
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Reconnect the z12 battery ECU assembly connector.
Install the No. 1 HV battery hose.
OK
NG
Be sure to wear insulated gloves and protective goggles.
Pre-procedure1
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the No. 1 HV battery hose.
Disconnect the z12 battery ECU assembly connector.
Before disconnecting the connector, check that it is not loose or disconnected.
Disconnect the z11 battery current sensor connector from the No. 1 traction battery device box assembly.
Before disconnecting the connector, check that it is not loose or disconnected.
Procedure1
| *a | Front view of wire harness connector
(to Battery ECU Assembly) |
| *b | Front view of wire harness connector
(to No. 1 Traction Battery Device Box Assembly (Battery Current Sensor)) |
Measure the resistance according to the value(s) in the tables below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(z12,z11)Location & Routingewd_type=routing;type=c,c;code=z12,z11 Click Connector(z12)Body>other>Battery ECU Assembly , HV Supply Battery Assemblyewd_type=component;type=c;code=z12;pinno=8,7,19,31 Click Connector(z11)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assemblyewd_type=component;type=c;code=z11;pinno=2,3,4,1 |
||
| z12-8 (IB1) - z11-2 (IB1) | Ignition switch off | Below 1 Ω |
| z12-7 (GIB) - z11-3 (GIB) | Ignition switch off | Below 1 Ω |
| z12-19 (IB0) - z11-4 (IB0) | Ignition switch off | Below 1 Ω |
| z12-31 (VIB) - z11-1 (VIB) | Ignition switch off | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(z12,z11)Location & Routingewd_type=routing;type=c,c;code=z12,z11 Click Connector(z12)Body>other>Battery ECU Assembly , HV Supply Battery Assemblyewd_type=component;type=c;code=z12;pinno=8,7,19,31 Click Connector(z11)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assemblyewd_type=component;type=c;code=z11;pinno=2,3,4,1 |
||
| z12-8 (IB1) or z11-2 (IB1) - Body ground and other terminals | Ignition switch off | 10 kΩ or higher |
| z12-7 (GIB) or z11-3 (GIB) - Body ground and other terminals | Ignition switch off | 10 kΩ or higher |
| z12-19 (IB0) or z11-4 (IB0) - Body ground and other terminals | Ignition switch off | 10 kΩ or higher |
| z12-31 (VIB) or z11-1 (VIB) - Body ground and other terminals | Ignition switch off | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the z11 battery current sensor connector to the No. 1 traction battery device box assembly.
Reconnect the z12 battery ECU assembly connector.
Install the No. 1 HV battery hose.
OK
NG
Be sure to wear insulated gloves and protective goggles.
Pre-procedure1
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the HV battery upper cover panel.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON.
Procedure1
| *a | Component with harness connected
(No. 1 Traction Battery Device Box Assembly (Battery Current Sensor)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(z11)Location & Routingewd_type=routing;type=c;code=z11 Click Connector(z11)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assemblyewd_type=component;type=c;code=z11;pinno=1,3 |
||
| z11-1 (VIB) - z11-3 (GIB) | Ignition switch ON | 4.6 to 5.4 V |
Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Install the HV battery upper cover panel.
OK
NG
Pre-procedure1
Remove the battery ECU assembly.
Procedure1
| *a | Component without harness connected
(Battery ECU Assembly) |
Measure the resistance according to the value(s) in the tables below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(z12)Location & Routingewd_type=routing;type=c;code=z12 Click Connector(z12)Body>other>Battery ECU Assembly , HV Supply Battery Assemblyewd_type=component;type=c;code=z12;pinno=34,7 |
||
| z12-34 (GND) - z12-7 (GIB) | Ignition switch off | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Install the battery ECU assembly.
OK
NG
Be sure to wear insulated gloves and protective goggles.
Pre-procedure1
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the HV battery upper cover panel.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON.
Procedure1
| *a | Component with harness connected
(No. 1 Traction Battery Device Box Assembly (Battery Current Sensor)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(z11)Location & Routingewd_type=routing;type=c;code=z11 Click Connector(z11)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assemblyewd_type=component;type=c;code=z11;pinno=2,3 |
||
| z11-2 (IB1) - z11-3 (GIB) | Ignition switch ON | 2.37 to 2.49 V |
Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Install the HV battery upper cover panel.
OK
NG
Be sure to wear insulated gloves and protective goggles.
Pre-procedure1
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the HV battery upper cover panel.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON.
Procedure1
| *a | Component with harness connected
(No. 1 Traction Battery Device Box Assembly (Battery Current Sensor)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(z11)Location & Routingewd_type=routing;type=c;code=z11 Click Connector(z11)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assemblyewd_type=component;type=c;code=z11;pinno=4,3 |
||
| z11-4 (IB0) - z11-3 (GIB) | Ignition switch ON | 2.51 to 2.63 V |
Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Install the HV battery upper cover panel.
OK
NG
Be sure to wear insulated gloves and protective goggles.
Pre-procedure1
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the HV battery upper cover panel.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON.
Procedure1
| *a | Component with harness connected
(No. 1 Traction Battery Device Box Assembly (Battery Current Sensor)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition |
|---|---|
|
Click Location & Routing(z11)Location & Routingewd_type=routing;type=c;code=z11 Click Connector(z11)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assemblyewd_type=component;type=c;code=z11;pinno=4,3 |
|
| z11-4 (IB0) - z11-3 (GIB) | Ignition switch ON |
Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.
| Result | Proceed to |
|---|---|
| 0.3 to 4.7 V | A |
| Below 0.3 V | B |
| 4.7 V or higher | C |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Install the HV battery upper cover panel.
A
B
C
Be sure to wear insulated gloves and protective goggles.
Pre-procedure1
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the HV battery upper cover panel.
Disconnect the z11 battery current sensor connector from the No. 1 traction battery device box assembly.
Before disconnecting the connector, check that it is not loose or disconnected.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON.
Procedure1
| *a | Front view of wire harness connector
(to No. 1 Traction Battery Device Box Assembly (Battery Current Sensor)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(z11)Location & Routingewd_type=routing;type=c;code=z11 Click Connector(z11)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assemblyewd_type=component;type=c;code=z11;pinno=4,3 |
||
| z11-4 (IB0) - z11-3 (GIB) | Ignition switch ON | 4.6 to 5.4 V |
Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.
If the ignition switch is turned to ON with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Reconnect the z11 battery current sensor connector to the No. 1 traction battery device box assembly.
Install the HV battery upper cover panel.
OK
NG
Be sure to wear insulated gloves and protective goggles.
Pre-procedure1
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the HV battery upper cover panel.
Disconnect the z11 battery current sensor connector from the No. 1 traction battery device box assembly.
Before disconnecting the connector, check that it is not loose or disconnected.
Procedure1
| *a | Front view of wire harness connector
(to No. 1 Traction Battery Device Box Assembly (Battery Current Sensor)) |
Measure the resistance according to the value(s) in the tables below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(z11)Location & Routingewd_type=routing;type=c;code=z11 Click Connector(z11)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assemblyewd_type=component;type=c;code=z11;pinno=1,4 |
||
| z11-1 (VIB) - z11-4 (IB0) | Ignition switch off | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the z11 battery current sensor connector to the No. 1 traction battery device box assembly.
Install the HV battery upper cover panel.
OK
NG
Be sure to wear insulated gloves and protective goggles.
Pre-procedure1
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the HV battery upper cover panel.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON.
Procedure1
| *a | Component with harness connected
(No. 1 Traction Battery Device Box Assembly (Battery Current Sensor)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition |
|---|---|
|
Click Location & Routing(z11)Location & Routingewd_type=routing;type=c;code=z11 Click Connector(z11)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assemblyewd_type=component;type=c;code=z11;pinno=2,3 |
|
| z11-2 (IB1) - z11-3 (GIB) | Ignition switch ON |
Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.
| Result | Proceed to |
|---|---|
| 0.3 to 4.7 V | A |
| Below 0.3 V | B |
| 4.7 V or higher | C |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Install the HV battery upper cover panel.
A
B
C
Be sure to wear insulated gloves and protective goggles.
Pre-procedure1
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the HV battery upper cover panel.
Disconnect the z11 battery current sensor connector from the No. 1 traction battery device box assembly
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON.
Procedure1
| *a | Front view of wire harness connector
(to No. 1 Traction Battery Device Box Assembly (Battery Current Sensor)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(z11)Location & Routingewd_type=routing;type=c;code=z11 Click Connector(z11)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assemblyewd_type=component;type=c;code=z11;pinno=2,3 |
||
| z11-2 (IB1) - z11-3 (GIB) | Ignition switch ON | 4.6 to 5.4 V |
Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.
If the ignition switch is turned to ON with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Reconnect the z11 battery current sensor connector to the No. 1 traction battery device box assembly
Install the HV battery upper cover panel.
OK
NG
Be sure to wear insulated gloves and protective goggles.
Pre-procedure1
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the ignition switch to ON (READY, unless instructed by the repair manual because this may cause a malfunction.
Remove the HV battery upper cover panel.
Disconnect the z11 battery current sensor connector from the No. 1 traction battery device box assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON.
Procedure1
| *a | Front view of wire harness connector
(to No. 1 Traction Battery Device Box Assembly (Battery Current Sensor)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(z11)Location & Routingewd_type=routing;type=c;code=z11 Click Connector(z11)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assemblyewd_type=component;type=c;code=z11;pinno=1,3 |
||
| z11-1 (VIB) - z11-3 (GIB) | Ignition switch ON | 4.6 to 5.4 V |
Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.
If the ignition switch is turned to ON with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Reconnect the z11 battery current sensor connector to the No. 1 traction battery device box assembly.
Install the HV battery upper cover panel.
OK
NG
Be sure to wear insulated gloves and protective goggles.
Pre-procedure1
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the HV battery upper cover panel.
Disconnect the z11 battery current sensor connector from the No. 1 traction battery device box assembly.
Procedure1
| *a | Front view of wire harness connector
(to No. 1 Traction Battery Device Box Assembly (Battery Current Sensor)) |
Measure the resistance according to the value(s) in the tables below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(z11)Location & Routingewd_type=routing;type=c;code=z11 Click Connector(z11)Body>other>HV Supply Battery Assembly , HV Battery Junction Block Assemblyewd_type=component;type=c;code=z11;pinno=1,2 |
||
| z11-1 (VIB) - z11-2 (IB1) | Ignition switch off | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the z11 battery current sensor connector from the No. 1 traction battery device box assembly.
Install the HV battery upper cover panel.
OK
NG