Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441185 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0E2D00  Hybrid/EV Battery Energy Control Module Hybrid/EV Battery Monitor Performance  


DESCRIPTION

The battery ECU assembly detects the voltage of each HV battery cell. The battery ECU assembly monitors its internal HV battery cell voltage detection circuits to detect malfunctions. If the battery ECU assembly detects a malfunction it will store this DTC.

HINT:

If this DTC is output, it will be necessary to replace the battery ECU assembly.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
P0E2D00 Hybrid/EV Battery Energy Control Module Hybrid/EV Battery Monitor Performance The battery ECU assembly detects a malfunction of its internal HV battery cell voltage detection circuits.
(1 trip detection logic)
·

Battery ECU assembly

·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly


Comes on Master Warning:
Comes on
HV Battery A

Related Data List
DTC No. Data List
P0E2D00 Hybrid/EV Battery Cell 1 to 48 Voltage

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

With the vehicle stopped and the shift position in P, turn the ignition switch to ON and wait for at least 70 seconds.

4.

Turn the ignition switch to ON (READY) and without depressing the accelerator pedal, and while depressing the brake pedal, change the shift position to D and wait for 1 minute. (Step A)

5.

Drive the vehicle 0.5 m (1.6 ft.) forward and perform step A.

6.

Drive the vehicle another 0.5 m (1.6 ft.) forward and perform step A. Repeat this procedure 5 times (minimum total driving distance: 2 m (6.6 ft.)).

7.

Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for DTC P1A001C.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P1A001C

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*

-

Disconnecting the low voltage connector of the HV battery


*: for AWD


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*.


*: for AWD


·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.

·
A358021C02
0.531,4.146 0.844,4.344 0.313,0.198 10 false *a 2.74,4.146 3.052,4.344 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

-

Accidents such as electric shock may result if the HV battery is disposed of improperly or abandoned. Therefore, make sure to return all HV batteries through an authorized collection agent.


·

Before returning the HV battery, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION

·

Before returning the HV supply stack sub-assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>RECOVERY INSPECTION

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery and HV supply stack sub-assemblies.

·
A358020

After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.



NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK DTC OUTPUT (HV BATTERY, HYBRID CONTROL)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > HV Battery > Trouble Codes
50001 398
Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
Only P0E2D00 for Hybrid battery system is output A
P0E2D00 and P1C8449 are output B
P0E2D00 is output and DTCs other than the DTCs in the table below are output C
P0E2D00 is output and hybrid battery system DTCs in the table below are output D
P0E2D00 is output and hybrid control system DTCs in the table below are output E


Table 1
System Relevant DTC
Hybrid battery system P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
P1A001C Hybrid Battery Stack 2 Cell Voltage Detection Voltage Out of Range
P301A1C Hybrid Battery Stack 1 Cell Voltage Detection Voltage Out of Range
Hybrid control system P0A1F94 Hybrid/EV Battery Energy Control Module Unexpected Operation


Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY CONNECTOR)

B

13.READ VALUE USING GTS (HYBRID/EV BATTERY CELL 1 TO 48 VOLTAGE)

C

2.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY CONNECTOR)

D

GO TO DTC CHART (HYBRID BATTERY SYSTEM)

E

2.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY CONNECTOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery hose.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



Procedure1

a.
A459833N01
1.333,0.385 1.719,0.625 0.385,0.24 1.917,0.385 2.302,0.625 0.385,0.24 1.365,0.417 1.688,0.594 0.323,0.177 10 true z13 1.948,0.417 2.271,0.594 0.323,0.177 10 true z15

Check the connections of the z13 and z15 battery ECU assembly connectors.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

The connector is connected securely and there are no contact problems.


Result:
Result Proceed to
OK A
Not connected securely The terminals are not damaged or corroded B
Connector z13 was not connected securely The terminals are damaged or corroded C
Connector z15 was not connected securely The terminals are damaged or corroded D



Post-procedure1

a.

Install the No. 1 HV battery hose.



A

3.READ VALUE USING GTS (HYBRID/EV BATTERY CELL 1 TO 48 VOLTAGE)

B

CONNECT SECURELY

C

REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

D

REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY

3.READ VALUE USING GTS (HYBRID/EV BATTERY CELL 1 TO 48 VOLTAGE)

Pre-procedure1

a.

None.


Procedure1

a.

Enter the following menus: Powertrain / HV Battery / Data List / Hybrid/EV Battery Cell 1 to 48 Voltage.

Powertrain > HV Battery > Data List
Tester Display
Hybrid/EV Battery Cell 1 Voltage
Hybrid/EV Battery Cell 2 Voltage
Hybrid/EV Battery Cell 3 Voltage
Hybrid/EV Battery Cell 4 Voltage
Hybrid/EV Battery Cell 5 Voltage
Hybrid/EV Battery Cell 6 Voltage
Hybrid/EV Battery Cell 7 Voltage
Hybrid/EV Battery Cell 8 Voltage
Hybrid/EV Battery Cell 9 Voltage
Hybrid/EV Battery Cell 10 Voltage
Hybrid/EV Battery Cell 11 Voltage
Hybrid/EV Battery Cell 12 Voltage
Hybrid/EV Battery Cell 13 Voltage
Hybrid/EV Battery Cell 14 Voltage
Hybrid/EV Battery Cell 15 Voltage
Hybrid/EV Battery Cell 16 Voltage
Hybrid/EV Battery Cell 17 Voltage
Hybrid/EV Battery Cell 18 Voltage
Hybrid/EV Battery Cell 19 Voltage
Hybrid/EV Battery Cell 20 Voltage
Hybrid/EV Battery Cell 21 Voltage
Hybrid/EV Battery Cell 22 Voltage
Hybrid/EV Battery Cell 23 Voltage
Hybrid/EV Battery Cell 24 Voltage
Hybrid/EV Battery Cell 25 Voltage
Hybrid/EV Battery Cell 26 Voltage
Hybrid/EV Battery Cell 27 Voltage
Hybrid/EV Battery Cell 28 Voltage
Hybrid/EV Battery Cell 29 Voltage
Hybrid/EV Battery Cell 30 Voltage
Hybrid/EV Battery Cell 31 Voltage
Hybrid/EV Battery Cell 32 Voltage
Hybrid/EV Battery Cell 33 Voltage
Hybrid/EV Battery Cell 34 Voltage
Hybrid/EV Battery Cell 35 Voltage
Hybrid/EV Battery Cell 36 Voltage
Hybrid/EV Battery Cell 37 Voltage
Hybrid/EV Battery Cell 38 Voltage
Hybrid/EV Battery Cell 39 Voltage
Hybrid/EV Battery Cell 40 Voltage
Hybrid/EV Battery Cell 41 Voltage
Hybrid/EV Battery Cell 42 Voltage
Hybrid/EV Battery Cell 43 Voltage
Hybrid/EV Battery Cell 44 Voltage
Hybrid/EV Battery Cell 45 Voltage
Hybrid/EV Battery Cell 46 Voltage
Hybrid/EV Battery Cell 47 Voltage
Hybrid/EV Battery Cell 48 Voltage
50003 398 334,335,336,337,338,339,340,341,342,343,344,345,346,347,348,349,350,351,352,353,354,355,356,357,358,359,360,361,362,363,364,365,366,367,368,369,370,371,372,373,374,375,376,377,378,379,380,381
Result:
Result Proceed to
2 or more adjacent HV battery cells with 1.6 V or less found from "Hybrid/EV Battery Cell 1 to 24 Voltage". A
2 or more adjacent HV battery cells with 1.6 V or less found from "Hybrid/EV Battery Cell 25 to 48 Voltage". B
Other than above C



Post-procedure1

a.

Turn the ignition switch off.



A

4.REPLACE BATTERY ECU ASSEMBLY

B

5.REPLACE BATTERY ECU ASSEMBLY

C

6.CHECK FREEZE FRAME DATA
4.REPLACE BATTERY ECU ASSEMBLY

NEXT

REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY

5.REPLACE BATTERY ECU ASSEMBLY

NEXT

REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

6.CHECK FREEZE FRAME DATA

Pre-procedure1

a.

None.


Procedure1

a.

Read the value of freeze frame data items "Hybrid/EV Battery Cell 1 Voltage" through "Hybrid/EV Battery Cell 48 Voltage" for DTC P0E2D00 and make a note if the value of any is 1.6 V or less.

Powertrain > HV Battery > DTC(P0E2D00) > Freeze Frame Data
Tester Display
Hybrid/EV Battery Cell 1 Voltage
Hybrid/EV Battery Cell 2 Voltage
Hybrid/EV Battery Cell 3 Voltage
Hybrid/EV Battery Cell 4 Voltage
Hybrid/EV Battery Cell 5 Voltage
Hybrid/EV Battery Cell 6 Voltage
Hybrid/EV Battery Cell 7 Voltage
Hybrid/EV Battery Cell 8 Voltage
Hybrid/EV Battery Cell 9 Voltage
Hybrid/EV Battery Cell 10 Voltage
Hybrid/EV Battery Cell 11 Voltage
Hybrid/EV Battery Cell 12 Voltage
Hybrid/EV Battery Cell 13 Voltage
Hybrid/EV Battery Cell 14 Voltage
Hybrid/EV Battery Cell 15 Voltage
Hybrid/EV Battery Cell 16 Voltage
Hybrid/EV Battery Cell 17 Voltage
Hybrid/EV Battery Cell 18 Voltage
Hybrid/EV Battery Cell 19 Voltage
Hybrid/EV Battery Cell 20 Voltage
Hybrid/EV Battery Cell 21 Voltage
Hybrid/EV Battery Cell 22 Voltage
Hybrid/EV Battery Cell 23 Voltage
Hybrid/EV Battery Cell 24 Voltage
Hybrid/EV Battery Cell 25 Voltage
Hybrid/EV Battery Cell 26 Voltage
Hybrid/EV Battery Cell 27 Voltage
Hybrid/EV Battery Cell 28 Voltage
Hybrid/EV Battery Cell 29 Voltage
Hybrid/EV Battery Cell 30 Voltage
Hybrid/EV Battery Cell 31 Voltage
Hybrid/EV Battery Cell 32 Voltage
Hybrid/EV Battery Cell 33 Voltage
Hybrid/EV Battery Cell 34 Voltage
Hybrid/EV Battery Cell 35 Voltage
Hybrid/EV Battery Cell 36 Voltage
Hybrid/EV Battery Cell 37 Voltage
Hybrid/EV Battery Cell 38 Voltage
Hybrid/EV Battery Cell 39 Voltage
Hybrid/EV Battery Cell 40 Voltage
Hybrid/EV Battery Cell 41 Voltage
Hybrid/EV Battery Cell 42 Voltage
Hybrid/EV Battery Cell 43 Voltage
Hybrid/EV Battery Cell 44 Voltage
Hybrid/EV Battery Cell 45 Voltage
Hybrid/EV Battery Cell 46 Voltage
Hybrid/EV Battery Cell 47 Voltage
Hybrid/EV Battery Cell 48 Voltage
50040 398 334,335,336,337,338,339,340,341,342,343,344,345,346,347,348,349,350,351,352,353,354,355,356,357,358,359,360,361,362,363,364,365,366,367,368,369,370,371,372,373,374,375,376,377,378,379,380,381 P0E2D00
Result:
Result Proceed to
The value of any Hybrid/EV Battery Cell 1 Voltage, Hybrid/EV Battery Cell 2 Voltage, Hybrid/EV Battery Cell 3 Voltage, Hybrid/EV Battery Cell 4 Voltage, Hybrid/EV Battery Cell 5 Voltage, Hybrid/EV Battery Cell 6 Voltage, Hybrid/EV Battery Cell 7 Voltage, Hybrid/EV Battery Cell 8 Voltage, Hybrid/EV Battery Cell 9 Voltage, Hybrid/EV Battery Cell 10 Voltage, Hybrid/EV Battery Cell 11 Voltage, Hybrid/EV Battery Cell 12 Voltage, Hybrid/EV Battery Cell 13 Voltage, Hybrid/EV Battery Cell 14 Voltage, Hybrid/EV Battery Cell 15 Voltage, Hybrid/EV Battery Cell 16 Voltage, Hybrid/EV Battery Cell 17 Voltage, Hybrid/EV Battery Cell 18 Voltage, Hybrid/EV Battery Cell 19 Voltage, Hybrid/EV Battery Cell 20 Voltage, Hybrid/EV Battery Cell 21 Voltage, Hybrid/EV Battery Cell 22 Voltage, Hybrid/EV Battery Cell 23 Voltage, Hybrid/EV Battery Cell 24 Voltage is 1.6 V or less A
The value of any Hybrid/EV Battery Cell 25 Voltage, Hybrid/EV Battery Cell 26 Voltage, Hybrid/EV Battery Cell 27 Voltage, Hybrid/EV Battery Cell 28 Voltage, Hybrid/EV Battery Cell 29 Voltage, Hybrid/EV Battery Cell 30 Voltage, Hybrid/EV Battery Cell 31 Voltage, Hybrid/EV Battery Cell 32 Voltage, Hybrid/EV Battery Cell 33 Voltage, Hybrid/EV Battery Cell 34 Voltage, Hybrid/EV Battery Cell 35 Voltage, Hybrid/EV Battery Cell 36 Voltage, Hybrid/EV Battery Cell 37 Voltage, Hybrid/EV Battery Cell 38 Voltage, Hybrid/EV Battery Cell 39 Voltage, Hybrid/EV Battery Cell 40 Voltage, Hybrid/EV Battery Cell 41 Voltage, Hybrid/EV Battery Cell 42 Voltage, Hybrid/EV Battery Cell 43 Voltage, Hybrid/EV Battery Cell 44 Voltage, Hybrid/EV Battery Cell 45 Voltage, Hybrid/EV Battery Cell 46 Voltage, Hybrid/EV Battery Cell 47 Voltage, Hybrid/EV Battery Cell 48 Voltage is 1.6 V or less B
Other than above C



Post-procedure1

a.

Turn the ignition switch off.



A

7.CHECK NO. 1 HV SUPPLY STACK SUB-ASSEMBLY (HYBRID BATTERY CELL 1 TO 24 VOLTAGE)

B

10.CHECK NO. 2 HV SUPPLY STACK SUB-ASSEMBLY (HYBRID BATTERY CELL 25 TO 48 VOLTAGE)

C

7.CHECK NO. 1 HV SUPPLY STACK SUB-ASSEMBLY (HYBRID BATTERY CELL 1 TO 24 VOLTAGE)
CAUTION:
·

Be sure to wear insulated gloves and protective goggles.

·

Disconnect only the connector corresponding to the HV battery cell to be checked. Do not disconnect the other connectors.



NOTICE:

Make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the voltage of each HV battery cell.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery hose.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



c.
A458602N01
2.385,0.083 2.74,0.323 0.354,0.24 2.417,0.104 2.719,0.302 0.302,0.198 10 true z15

Disconnect the z15 battery ECU assembly connector.


Procedure1

a.
A459573C01
1.448,0.073 1.875,0.26 0.427,0.188 0.406,2.365 1.458,2.219 true 1.573,1.948 0.385,0.885 true 0.49,2.771 1.563,2.219 true 1.656,1.948 0.823,0.771 true 0.792,2.969 1.656,2.219 true 1.521,0.542 1.792,1.958 true 1.135,3.146 1.771,2.208 true 2.385,0.573 1.896,1.958 true 2.823,0.667 1.979,1.948 true 2.896,1.042 2.083,1.958 true 2.896,1.375 2.188,1.969 true 2.906,1.688 2.302,1.99 true 2.927,2.458 2.281,2.188 true 2.927,2.667 2.188,2.188 true 1.531,3.146 1.865,2.219 true 1.896,3.104 1.958,2.229 true 2.583,3.104 2.073,2.208 true 2.927,2.281 2.313,2.094 true 2.948,2 2.198,2.052 true 2.688,2.844 2.083,2.073 true 2.26,3.125 1.979,2.094 true 1.865,2.063 1.792,0.531 true 1.156,0.573 1.75,2.073 true 1.656,2.083 0.438,1.292 true 0.448,1.75 1.552,2.104 true 0.094,2.313 0.406,2.51 0.313,0.198 10 false GA0 1.521,0.094 1.833,0.292 0.313,0.198 10 false z15 0.135,1.667 0.448,1.865 0.313,0.198 10 false VA2 0.208,2.708 0.521,2.906 0.313,0.198 10 false VA3 0.646,0.635 0.958,0.833 0.313,0.198 10 false VA4 0.135,1.208 0.448,1.406 0.313,0.198 10 false VA5 0.573,3 0.885,3.198 0.313,0.198 10 false VA6 1.385,0.396 1.698,0.594 0.313,0.198 10 false VA7 1.01,0.396 1.323,0.594 0.313,0.198 10 false VA8 1,3.188 1.313,3.385 0.313,0.198 10 false VA9 2.271,0.438 2.667,0.635 0.396,0.198 10 false VA10 1.688,0.406 2.083,0.615 0.396,0.208 10 false VA11 1.375,3.188 1.771,3.385 0.396,0.198 10 false VA12 2.719,0.51 3.115,0.708 0.396,0.198 10 false VA13 2.167,3.167 2.563,3.365 0.396,0.198 10 false VA14 1.76,3.177 2.156,3.375 0.396,0.198 10 false VA15 2.948,0.927 3.344,1.125 0.396,0.198 10 false VA16 2.688,2.885 3.083,3.083 0.396,0.198 10 false VA17 2.563,3.146 2.958,3.344 0.396,0.198 10 false VA18 2.969,1.313 3.365,1.51 0.396,0.198 10 false VA19 2.99,1.938 3.385,2.135 0.396,0.198 10 false VA20 3,2.656 3.396,2.854 0.396,0.198 10 false VA21 2.979,1.625 3.375,1.823 0.396,0.198 10 false VA22 3.01,2.271 3.406,2.469 0.396,0.198 10 false VA23 3.01,2.438 3.406,2.635 0.396,0.198 10 false VA24 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 0.24,0.75 0.552,0.948 0.313,0.198 10 false VA1
*a Front view of wire harness connector
(to Battery ECU Assembly)


Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage of the HV battery cells whose value in the freeze frame data was 1.6 V or less only.


Tester Connection Hybrid Battery Cell Condition

Click Location & Routing(z15)Location & Routing

Click Connector(z15)Body>other>Battery ECU Assembly , HV Supply Battery Assembly

z15-28 (GA0) - z15-5 (VA1) 1 Always
z15-5 (VA1) - z15-17 (VA2) 2 Always
z15-17 (VA2) - z15-29(VA3) 3 Always
z15-29 (VA3) - z15-6 (VA4) 4 Always
z15-6 (VA4) - z15-18 (VA5) 5 Always
z15-18 (VA5) - z15-30 (VA6) 6 Always
z15-30 (VA6) - z15-7 (VA7) 7 Always
z15-7 (VA7) - z15-19 (VA8) 8 Always
z15-19 (VA8) - z15-31 (VA9) 9 Always
z15-31 (VA9) - z15-8 (VA10) 10 Always
z15-8 (VA10) - z15-20 (VA11) 11 Always
z15-20 (VA11) - z15-32 (VA12) 12 Always
z15-32 (VA12) - z15-9 (VA13) 13 Always
z15-9 (VA13) - z15-21 (VA14) 14 Always
z15-21 (VA14) - z15-33 (VA15) 15 Always
z15-33 (VA15) - z15-10 (VA16) 16 Always
z15-10 (VA16) - z15-22 (VA17) 17 Always
z15-22 (VA17) - z15-34 (VA18) 18 Always
z15-34 (VA18) - z15-11 (VA19) 19 Always
z15-11 (VA19) - z15-23 (VA20) 20 Always
z15-23 (VA20) - z15-35 (VA21) 21 Always
z15-35 (VA21) - z15-12 (VA22) 22 Always
z15-12 (VA22) - z15-24 (VA23) 23 Always
z15-24 (VA23) -z15-36 (VA24) 24 Always

CAUTION:

Make sure not to cross the electrodes of an electrical tester measurement terminals.


NOTICE:

Make sure to check the polarity of each terminal (positive (+) or negative (-)) before connecting a tester.


Result:
Result Proceed to
The voltage between the terminals is 1.6 V or less. A
Other than above B



Post-procedure1

a.

Reconnect the z15 battery ECU assembly connector.


b.

Install the No. 1 HV battery hose.



A

8.CHECK BATTERY ECU ASSEMBLY (GA0 - VA24)

B

8.CHECK BATTERY ECU ASSEMBLY (GA0 - VA24)
NOTICE:

Make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the resistance.


Pre-procedure1

a.

Remove the battery ECU assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

HINT:

Only inspect the terminals of the battery ECU assembly which correspond to the HV battery cells which measured 1.6 V or less in the previous step.


A459834C01
5.104,0.448 5.531,0.688 0.427,0.24 4.875,5.74 3.885,5.365 true 4.646,6.063 3.781,5.333 true 3.917,6.125 3.625,5.365 true 3.771,6.354 3.531,5.365 true 3.26,6.365 3.385,5.365 true 3.083,6.125 3.302,5.365 true 1.833,6.25 3.042,5.365 true 1.833,5.75 2.938,5.365 true 1.844,5.281 2.906,5.219 true 1.833,4.677 2.885,5.094 true 1.833,4.083 3.042,5.198 true 2.417,4.302 3.01,5.052 true 2.469,4.063 3.146,5.042 true 2.5,6.104 3.188,5.24 true 2.646,6.333 3.156,5.385 true 2.896,4.292 3.26,5.177 true 3.063,3.979 3.302,5.063 true 3.427,5.229 3.51,6.115 true 3.385,4.354 3.427,5.063 true 3.813,4.302 3.563,5.094 true 4.271,4.063 3.667,5.083 true 4.625,4.417 3.792,5.094 true 3.573,4.031 3.5,5.188 true 4.333,6.417 3.646,5.219 true 5.052,4.948 3.802,5.198 true 0.135,0.052 0.448,0.25 0.313,0.198 10 false *a 1.469,5.677 2.083,5.875 0.615,0.198 10 false VA24 1.469,5.219 2.083,5.417 0.615,0.198 10 false VA23 1.427,4.615 2.042,4.813 0.615,0.198 10 false VA22 1.479,6.198 2.094,6.396 0.615,0.198 10 false VA21 1.479,3.99 2.094,4.188 0.615,0.198 10 false VA20 2.125,4.146 2.74,4.344 0.615,0.198 10 false VA19 2.469,6.406 3.083,6.604 0.615,0.198 10 false VA18 2.26,6.146 2.875,6.344 0.615,0.198 10 false VA17 2.188,3.917 2.802,4.115 0.615,0.198 10 false VA16 2.833,6.156 3.448,6.354 0.615,0.198 10 false VA15 2.656,4.156 3.271,4.354 0.615,0.198 10 false VA14 2.896,3.813 3.51,4.01 0.615,0.198 10 false VA13 3.094,6.406 3.708,6.604 0.615,0.198 10 false VA12 3.375,6.167 3.99,6.365 0.615,0.198 10 false VA11 3.208,4.188 3.823,4.385 0.615,0.198 10 false VA10 3.635,6.406 4.25,6.604 0.615,0.198 10 false VA9 3.479,3.865 4.094,4.063 0.615,0.198 10 false VA8 3.729,4.125 4.344,4.323 0.615,0.198 10 false VA7 3.885,6.188 4.5,6.385 0.615,0.198 10 false VA6 4.25,6.469 4.865,6.667 0.615,0.198 10 false VA5 4.188,3.896 4.802,4.094 0.615,0.198 10 false VA4 4.583,6.094 5.198,6.292 0.615,0.198 10 false VA3 5.125,4.865 5.74,5.063 0.615,0.198 10 false VA2 4.563,4.26 5.177,4.458 0.615,0.198 10 false VA1 4.917,5.781 5.531,5.979 0.615,0.198 10 false GA0 5.177,0.479 5.51,0.656 0.333,0.177 10 true z15
*a Component without harness connected
(Battery ECU Assembly)
- -


Standard Resistance:
Tester Connection
(Tester Probe Polarity)
Hybrid Battery Cell Condition Specified Condition

Click Location & Routing(z15)Location & Routing

Click Connector(z15)Body>other>Battery ECU Assembly , HV Supply Battery Assembly

z15-28 (GA0) (-) - z15-5 (VA1) (+) 1 Always 50 kΩ or more
z15-5 (VA1) (-) - z15-17 (VA2) (+) 2 Always 50 kΩ or more
z15-17 (VA2) (-) - z15-29 (VA3) (+) 3 Always 50 kΩ or more
z15-29 (VA3) (-) - z15-6 (VA4) (+) 4 Always 50 kΩ or more
z15-6 (VA4) (-) - z15-18 (VA5) (+) 5 Always 50 kΩ or more
z15-18 (VA5) (-) - z15-30 (VA6) (+) 6 Always 50 kΩ or more
z15-30 (VA6) (-) - z15-7 (VA7) (+) 7 Always 50 kΩ or more
z15-7 (VA7) (-) - z15-19 (VA8) (+) 8 Always 50 kΩ or more
z15-19 (VA8) (-) - z15-31 (VA9) (+) 9 Always 50 kΩ or more
z15-31 (VA9) (-) - z15-8 (VA10) (+) 10 Always 50 kΩ or more
z15-8 (VA10) (-) - z15-20 (VA11) (+) 11 Always 50 kΩ or more
z15-20 (VA11) (-) - z15-32 (VA12) (+) 12 Always 50 kΩ or more
z15-32 (VA12) (-) - z15-9 (VA13) (+) 13 Always 50 kΩ or more
z15-9 (VA13)(-) - z15-21 (VA14) (+) 14 Always 50 kΩ or more
z15-21 (VA14) (-) - z15-33 (VA15) (+) 15 Always 50 kΩ or more
z15-33 (VA15) (-) - z15-10 (VA16) (+) 16 Always 50 kΩ or more
z15-10 (VA16) (-) - z15-22 (VA17) (+) 17 Always 50 kΩ or more
z15-22 (VA17) (-) - z15-34 (VA18) (+) 18 Always 50 kΩ or more
z15-34 (VA18) (-) - z15-11 (VA19) (+) 19 Always 50 kΩ or more
z15-11 (VA19) (-) - z15-23 (VA20) (+) 20 Always 50 kΩ or more
z15-23 (VA20) (-) - z15-35 (VA21) (+) 21 Always 50 kΩ or more
z15-35 (VA21)(-) - z15-12 (VA22) (+) 22 Always 50 kΩ or more
z15-12 (VA22) (-) - z15-24 (VA23) (+) 23 Always 50 kΩ or more
z15-24 (VA23) (-) - z15-36 (VA24) (+) 24 Always 50 kΩ or more


NOTICE:
·

Make sure to check the polarity of each terminal (positive (+) or negative (-)) before connecting a tester.

·

Read the resistance after the value has stabilized.

·

In order to avoid damaging the terminals of the battery ECU assembly, make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the resistance of the battery ECU assembly.



Result:
Result Proceed to
The voltage between the terminals is 50 kΩ or more. A
Other than above B



Post-procedure1

a.

Install the battery ECU assembly.



A

REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY

B

9.REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY
9.REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY

NEXT

10.CHECK NO. 2 HV SUPPLY STACK SUB-ASSEMBLY (HYBRID BATTERY CELL 25 TO 48 VOLTAGE)
CAUTION:
·

Be sure to wear insulated gloves and protective goggles.

·

Disconnect only the connector corresponding to the HV battery cell to be checked. Do not disconnect the other connectors.



NOTICE:

Make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the voltage of each HV battery cell.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery hose.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



c.
A458603N01
1.667,0.135 2.021,0.385 0.354,0.25 1.698,0.167 1.99,0.365 0.292,0.198 10 true z13

Disconnect the z13 battery ECU assembly connector.


Procedure1

a.
A459572C01
1.448,0.073 1.875,0.26 0.427,0.188 0.406,2.365 1.458,2.219 true 1.573,1.948 0.385,0.885 true 0.49,2.771 1.563,2.219 true 1.656,1.948 0.823,0.771 true 0.792,2.969 1.656,2.219 true 1.531,0.479 1.792,1.958 true 1.135,3.146 1.771,2.208 true 2.385,0.573 1.896,1.958 true 2.823,0.667 1.979,1.948 true 2.896,1.042 2.083,1.958 true 2.896,1.375 2.188,1.969 true 2.906,1.688 2.302,1.99 true 2.927,2.458 2.281,2.188 true 2.927,2.667 2.188,2.188 true 1.531,3.146 1.865,2.219 true 1.896,3.104 1.958,2.229 true 2.583,3.104 2.073,2.208 true 2.927,2.281 2.313,2.094 true 2.948,2 2.198,2.052 true 2.688,2.844 2.083,2.073 true 2.26,3.125 1.979,2.094 true 1.865,2.063 1.792,0.531 true 1.156,0.573 1.75,2.073 true 1.656,2.083 0.438,1.292 true 0.448,1.75 1.552,2.104 true 0.094,2.313 0.406,2.51 0.313,0.198 10 false GA1 1.521,0.094 1.833,0.292 0.313,0.198 10 false z13 0.104,1.667 0.625,1.865 0.521,0.198 10 false VA26 0.146,2.719 0.656,2.938 0.51,0.219 10 false VA27 0.646,0.635 1.052,0.833 0.406,0.198 10 false VA28 0.104,1.208 0.563,1.406 0.458,0.198 10 false VA29 0.573,3 0.969,3.198 0.396,0.198 10 false VA30 1.354,0.313 1.865,0.521 0.51,0.208 10 false VA31 1.01,0.396 1.427,0.604 0.417,0.208 10 false VA32 1,3.188 1.396,3.385 0.396,0.198 10 false VA33 2.271,0.438 2.667,0.635 0.396,0.198 10 false VA34 1.688,0.406 2.083,0.615 0.396,0.208 10 false VA35 1.375,3.188 1.771,3.385 0.396,0.198 10 false VA36 2.719,0.51 3.115,0.708 0.396,0.198 10 false VA37 2.167,3.167 2.563,3.365 0.396,0.198 10 false VA38 1.76,3.177 2.156,3.375 0.396,0.198 10 false VA39 2.948,0.927 3.344,1.125 0.396,0.198 10 false VA40 2.688,2.885 3.083,3.083 0.396,0.198 10 false VA41 2.563,3.146 2.958,3.344 0.396,0.198 10 false VA42 2.969,1.313 3.365,1.51 0.396,0.198 10 false VA43 2.99,1.938 3.385,2.135 0.396,0.198 10 false VA44 3,2.656 3.396,2.854 0.396,0.198 10 false VA45 2.979,1.625 3.375,1.823 0.396,0.198 10 false VA46 3.01,2.271 3.406,2.469 0.396,0.198 10 false VA47 3.01,2.438 3.406,2.635 0.396,0.198 10 false VA48 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 0.208,0.75 0.635,0.948 0.427,0.198 10 false VA25
*a Front view of wire harness connector
(to Battery ECU Assembly)


Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage of the HV battery cells whose value in the freeze frame data was 1.6 V or less only.


Tester Connection Hybrid Battery Cell Condition

Click Location & Routing(z13)Location & Routing

Click Connector(z13)Body>other>Battery ECU Assembly , HV Supply Battery Assembly

z13-28 (GA1) - z13-5 (VA25) 25 Always
z13-5 (VA25) - z13-17 (VA26) 26 Always
z13-17 (VA26) - z13-29 (VA27) 27 Always
z13-29 (VA27) - z13-6 (VA28) 28 Always
z13-6 (VA28) - z13-18 (VA29) 29 Always
z13-18 (VA29) - z13-30 (VA30) 30 Always
z13-30 (VA30) - z13-7 (VA31) 31 Always
z13-7 (VA31) - z13-19 (VA32) 32 Always
z13-19 (VA32) - z13-31 (VA33) 33 Always
z13-31 (VA33) - z13-8 (VA34) 34 Always
z13-8 (VA34) - z13-20 (VA35) 35 Always
z13-20 (VA35) - z13-32 (VA36) 36 Always
z13-32 (VA36) - z13-9 (VA37) 37 Always
z13-9 (VA37) - z13-21 (VA38) 38 Always
z13-21 (VA38) - z13-33 (VA39) 39 Always
z13-33 (VA39) - z13-10 (VA40) 40 Always
z13-10 (VA40) - z13-22 (VA41) 41 Always
z13-22 (VA41) - z13-34 (VA42) 42 Always
z13-34 (VA42) - z13-11 (VA43) 43 Always
z13-11 (VA43) - z13-23 (VA44) 44 Always
z13-23 (VA44) - z13-35 (VA45) 45 Always
z13-35 (VA45) - z13-12 (VA46) 46 Always
z13-12 (VA46) - z13-24 (VA47) 47 Always
z13-24 (VA47) - z13-36(VA48) 48 Always

CAUTION:

Make sure not to cross the electrodes of an electrical tester measurement terminals.


NOTICE:

Make sure to check the polarity of each terminal (positive (+) or negative (-)) before connecting a tester.


Result:
Result Proceed to
The voltage between the terminals is 1.6 V or less. A
Other than above B



Post-procedure1

a.

Reconnect the z13 battery ECU assembly connector.


b.

Install the No. 1 HV battery hose.



A

11.CHECK BATTERY ECU ASSEMBLY (GA1 to VA48)

B

11.CHECK BATTERY ECU ASSEMBLY (GA1 to VA48)
NOTICE:

Make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the resistance.


Pre-procedure1

a.

Remove the battery ECU assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

HINT:

Only inspect the terminals of the battery ECU assembly which correspond to the HV battery cells which measured 1.6 V or less in the previous step.


A459862C01
3.75,0.448 4.177,0.688 0.427,0.24 4.875,5.74 3.885,5.365 true 4.646,6.063 3.781,5.333 true 3.917,6.125 3.625,5.365 true 3.771,6.354 3.531,5.365 true 3.26,6.365 3.385,5.365 true 3.083,6.125 3.302,5.365 true 1.833,6.25 3.042,5.365 true 1.833,5.75 2.938,5.365 true 1.844,5.281 2.906,5.219 true 1.833,4.677 2.885,5.094 true 1.833,4.083 3.042,5.198 true 2.417,4.302 3.01,5.052 true 2.469,4.063 3.146,5.042 true 2.5,6.104 3.188,5.24 true 2.646,6.333 3.156,5.385 true 2.896,4.292 3.26,5.177 true 3.063,3.979 3.302,5.063 true 3.427,5.229 3.51,6.115 true 3.385,4.354 3.427,5.063 true 3.813,4.302 3.563,5.094 true 4.271,4.063 3.667,5.083 true 4.625,4.417 3.792,5.094 true 3.573,4.031 3.5,5.188 true 4.333,6.417 3.646,5.219 true 5.052,4.948 3.802,5.198 true 0.135,0.052 0.448,0.25 0.313,0.198 10 false *a 1.469,5.677 2.083,5.875 0.615,0.198 10 false VA48 1.469,5.219 2.083,5.417 0.615,0.198 10 false VA47 1.427,4.615 2.042,4.813 0.615,0.198 10 false VA46 1.479,6.198 2.094,6.396 0.615,0.198 10 false VA45 1.479,3.99 2.094,4.188 0.615,0.198 10 false VA44 2.125,4.146 2.74,4.344 0.615,0.198 10 false VA43 2.469,6.406 3.083,6.604 0.615,0.198 10 false VA42 2.26,6.146 2.875,6.344 0.615,0.198 10 false VA41 2.188,3.917 2.802,4.115 0.615,0.198 10 false VA40 2.833,6.156 3.448,6.354 0.615,0.198 10 false VA39 2.656,4.156 3.271,4.354 0.615,0.198 10 false VA38 2.896,3.813 3.51,4.01 0.615,0.198 10 false VA37 3.094,6.406 3.708,6.604 0.615,0.198 10 false VA36 3.375,6.167 3.99,6.365 0.615,0.198 10 false VA35 3.208,4.188 3.823,4.385 0.615,0.198 10 false VA34 3.635,6.406 4.25,6.604 0.615,0.198 10 false VA33 3.479,3.865 4.094,4.063 0.615,0.198 10 false VA32 3.729,4.125 4.344,4.323 0.615,0.198 10 false VA31 3.854,6.188 4.469,6.385 0.615,0.198 10 false VA30 4.25,6.469 4.865,6.667 0.615,0.198 10 false VA29 4.188,3.896 4.802,4.094 0.615,0.198 10 false VA28 4.583,6.094 5.198,6.292 0.615,0.198 10 false VA27 5.125,4.865 5.74,5.063 0.615,0.198 10 false VA26 4.563,4.26 5.177,4.458 0.615,0.198 10 false VA25 4.917,5.781 5.531,5.979 0.615,0.198 10 false GA1 3.813,0.479 4.146,0.656 0.333,0.177 10 true z13
*a Component without harness connected
(Battery ECU Assembly)
- -


Standard Resistance:
Tester Connection
(Tester Probe Polarity)
Hybrid Battery Cell Condition Specified Condition

Click Location & Routing(z13)Location & Routing

Click Connector(z13)Body>other>Battery ECU Assembly , HV Supply Battery Assembly

z13-28 (GA1) (-) - z13-5 (VA25) (+) 25 Always 50 kΩ or more
z13-5 (VA25) (-) - z13-17 (VA26) (+) 26 Always 50 kΩ or more
z13-17 (VA26) (-) - z13-29 (VA27) (+) 27 Always 50 kΩ or more
z13-29 (VA27) (-) - z13-6 (VA28) (+) 28 Always 50 kΩ or more
z13-6 (VA28) (-) - z13-18 (VA29) (+) 29 Always 50 kΩ or more
z13-18 (VA29) (-) - z13-30 (VA30) (+) 30 Always 50 kΩ or more
z13-30 (VA30) (-) - z13-7 (VA31) (+) 31 Always 50 kΩ or more
z13-7 (VA31) (-) - z13-19 (VA32) (+) 32 Always 50 kΩ or more
z13-19 (VA32) (-) - z13-31 (VA33) (+) 33 Always 50 kΩ or more
z13-31 (VA33) (-) - z13-8 (VA34) (+) 34 Always 50 kΩ or more
z13-8 (VA34) (-) - z13-20 (VA35) (+) 35 Always 50 kΩ or more
z13-20 (VA35) (-) - z13-32 (VA36) (+) 36 Always 50 kΩ or more
z13-32 (VA36) (-) - z13-9 (VA37) (+) 37 Always 50 kΩ or more
z13-9 (VA37) (-) - z13-21 (VA38) (+) 38 Always 50 kΩ or more
z13-21 (VA38) (-) - z13-33 (VA39) (+) 39 Always 50 kΩ or more
z13-33 (VA39) (-) - z13-10 (VA40) (+) 40 Always 50 kΩ or more
z13-10 (VA40) (-) - z13-22 (VA41) (+) 41 Always 50 kΩ or more
z13-22 (VA41) (-) - z13-34 (VA42) (+) 42 Always 50 kΩ or more
z13-34 (VA42) (-) - z13-11 (VA43) (+) 43 Always 50 kΩ or more
z13-11 (VA43) (-) - z13-23 (VA44) (+) 44 Always 50 kΩ or more
z13-23 (VA44) (-) - z13-35 (VA45) (+) 45 Always 50 kΩ or more
z13-35 (VA45) (-) - z13-12 (VA46) (+) 46 Always 50 kΩ or more
z13-12 (VA46) (-) - z13-24 (VA47) (+) 47 Always 50 kΩ or more
z13-24 (VA47) (-) -z13-36 (VA48) (+) 48 Always 50 kΩ or more


NOTICE:
·

Make sure to check the polarity of each terminal (positive (+) or negative (-)) before connecting a tester.

·

Read the resistance after the value has stabilized.

·

In order to avoid damaging the terminals of the battery ECU assembly, make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the resistance of the battery ECU assembly.



Result:
Result Proceed to
The voltage between the terminals is 50 kΩ or more. A
Other than above B



Post-procedure1

a.

Install the battery ECU assembly.



A

REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

B

12.REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY
12.REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

NEXT

13.READ VALUE USING GTS (HYBRID/EV BATTERY CELL 1 TO 48 VOLTAGE)

Pre-procedure1

a.

None.


Procedure1

a.

Enter the following menus: Powertrain / HV Battery / Data List / Hybrid/EV Battery Cell 1 to 48 Voltage.

Powertrain > HV Battery > Data List
Tester Display
Hybrid/EV Battery Cell 1 Voltage
Hybrid/EV Battery Cell 2 Voltage
Hybrid/EV Battery Cell 3 Voltage
Hybrid/EV Battery Cell 4 Voltage
Hybrid/EV Battery Cell 5 Voltage
Hybrid/EV Battery Cell 6 Voltage
Hybrid/EV Battery Cell 7 Voltage
Hybrid/EV Battery Cell 8 Voltage
Hybrid/EV Battery Cell 9 Voltage
Hybrid/EV Battery Cell 10 Voltage
Hybrid/EV Battery Cell 11 Voltage
Hybrid/EV Battery Cell 12 Voltage
Hybrid/EV Battery Cell 13 Voltage
Hybrid/EV Battery Cell 14 Voltage
Hybrid/EV Battery Cell 15 Voltage
Hybrid/EV Battery Cell 16 Voltage
Hybrid/EV Battery Cell 17 Voltage
Hybrid/EV Battery Cell 18 Voltage
Hybrid/EV Battery Cell 19 Voltage
Hybrid/EV Battery Cell 20 Voltage
Hybrid/EV Battery Cell 21 Voltage
Hybrid/EV Battery Cell 22 Voltage
Hybrid/EV Battery Cell 23 Voltage
Hybrid/EV Battery Cell 24 Voltage
Hybrid/EV Battery Cell 25 Voltage
Hybrid/EV Battery Cell 26 Voltage
Hybrid/EV Battery Cell 27 Voltage
Hybrid/EV Battery Cell 28 Voltage
Hybrid/EV Battery Cell 29 Voltage
Hybrid/EV Battery Cell 30 Voltage
Hybrid/EV Battery Cell 31 Voltage
Hybrid/EV Battery Cell 32 Voltage
Hybrid/EV Battery Cell 33 Voltage
Hybrid/EV Battery Cell 34 Voltage
Hybrid/EV Battery Cell 35 Voltage
Hybrid/EV Battery Cell 36 Voltage
Hybrid/EV Battery Cell 37 Voltage
Hybrid/EV Battery Cell 38 Voltage
Hybrid/EV Battery Cell 39 Voltage
Hybrid/EV Battery Cell 40 Voltage
Hybrid/EV Battery Cell 41 Voltage
Hybrid/EV Battery Cell 42 Voltage
Hybrid/EV Battery Cell 43 Voltage
Hybrid/EV Battery Cell 44 Voltage
Hybrid/EV Battery Cell 45 Voltage
Hybrid/EV Battery Cell 46 Voltage
Hybrid/EV Battery Cell 47 Voltage
Hybrid/EV Battery Cell 48 Voltage
50003 398 334,335,336,337,338,339,340,341,342,343,344,345,346,347,348,349,350,351,352,353,354,355,356,357,358,359,360,361,362,363,364,365,366,367,368,369,370,371,372,373,374,375,376,377,378,379,380,381
Result:
Result Proceed to
2 or more adjacent HV battery cells with 1.6 V or less found from "Hybrid/EV Battery Cell 1 to 24 Voltage". A
2 or more adjacent HV battery cells with 1.6 V or less found from "Hybrid/EV Battery Cell 25 to 48 Voltage". B



Post-procedure1

a.

Turn the ignition switch off.



A

14.REPLACE BATTERY ECU ASSEMBLY

B

15.REPLACE BATTERY ECU ASSEMBLY
14.REPLACE BATTERY ECU ASSEMBLY

NEXT

REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY

15.REPLACE BATTERY ECU ASSEMBLY

NEXT

REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY