Refer to DTC P084011.
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>P084011
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|---|---|
| P084015 | Transmission Fluid Pressure Sensor/Switch "A" Circuit Short To Battery or Open | When 2 seconds or more have elapsed since engine start, an open or short to +B is detected in the oil pressure sensor circuit for 0.5 seconds or more (1-trip detection logic). | ·
Wire harness or connector ·
Oil pressure sensor ·
TCM |
Comes on | DTC stored | Transmission | A | SAE Code:
P0843 |
This DTC indicates an open or a short to +B in the oil pressure sensor circuit. If there is an open or a short to +B in the oil pressure sensor circuit, the TCM detects the malfunction, illuminates the MIL and stores a DTC.
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine and wait for 5 seconds or more.
Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
Input the DTC: P084015.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Refer to DTC P084011.
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>P084011
Do not perform a stall test if there are any people or objects near the vehicle.
The vehicle could begin moving suddenly, resulting in a serious accident.
Do not perform a stall test if any wheel chock is out of position.
The vehicle could begin moving suddenly, resulting in a serious accident.
Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.
The vehicle could begin moving suddenly, resulting in a serious accident.
Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
A stall speed test should always be performed with at least 2 people. One person should observe the condition of the wheels and wheel chocks while the other is performing the test.
This test must be performed after checking and confirming that the engine is normal.
Perform this test with the CVT fluid temperature between 50 and 100°C (122 and 212°F).
Perform this test with the air conditioning off.
Do not perform the stall speed test for longer than 5 seconds.
When performing the stall speed test repeatedly, wait for 15 seconds or more between tests.
Perform this test with the AUTO function (shift-linked function) of the electric parking brake system off.
Pre-procedure1
Warm up the engine.
Fully apply the parking brake and chock all 4 wheels.
When the parking brake indicator (red) is illuminated after the electric parking brake switch has been pulled to the lock side, the maximum amount of braking force is applied if the electric parking brake switch is pulled to the lock side one more time.
Procedure1
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Activate the TC Terminal | ·
Changes to the fluid temperature detection mode ·
Performs stall speed test ·
Performs secondary oil pressure test |
ON or OFF | (Vehicle Condition)
Ignition switch ON, engine stopped and shift lever in P |
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Belt Clamping Force Sensor | Secondary oil pressure value | Min.: -64 MPa
Max.: 63.998 MPa |
Secondary oil pressure inspection:
3.4 to 4.2 MPa (34.7 to 42.8 kgf/cm2, 493 to 609 psi): D position stall test |
- |
| Active Test Display |
|---|
| Activate the TC Terminal |
| Data List Display |
|---|
| Belt Clamping Force Sensor |
| Result | Proceed to |
|---|---|
| The value of Belt Clamping Force Sensor is between 3.4 and 4.2 MPa | A |
| None of the above conditions are met | B |
3.4 MPa=34.7 kgf/cm2
3.4 MPa=493 psi
4.2 MPa=42.8 kgf/cm2
4.2 MPa=609 psi
Post-procedure1
None.
A
B
A stall speed test should always be performed with at least 2 people. One person should observe the condition of the wheels and wheel chocks while the other is performing the test.
This test must be performed after checking and confirming that the engine is normal.
Perform this test with the CVT fluid temperature between 50 and 100°C (122 and 212°F).
Perform this test with the air conditioning off.
Do not perform the stall speed test for longer than 5 seconds.
When performing the stall speed test repeatedly, wait for 15 seconds or more between tests.
Perform this test with the AUTO function (shift-linked function) of the electric parking brake system off.
Pre-procedure1
Warm up the engine.
Fully apply the parking brake and chock all 4 wheels.
When the parking brake indicator (red) is illuminated after the electric parking brake switch has been pulled to the lock side, the maximum amount of braking force is applied if the electric parking brake switch is pulled to the lock side one more time.
Procedure1
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Activate the TC Terminal | ·
Changes to the fluid temperature detection mode ·
Performs stall speed test ·
Performs secondary oil pressure test |
ON or OFF | (Vehicle Condition)
Ignition switch ON, engine stopped and shift lever in P |
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Belt Clamping Force Sensor | Secondary oil pressure value | Min.: -64 MPa
Max.: 63.998 MPa |
Secondary oil pressure inspection:
2.4 to 3.2 MPa (24.5 to 32.6 kgf/cm2, 348 to 464 psi): R position stall test |
- |
| Active Test Display |
|---|
| Activate the TC Terminal |
| Data List Display |
|---|
| Belt Clamping Force Sensor |
| Result | Proceed to |
|---|---|
| The value of Belt Clamping Force Sensor is between 2.4 and 3.2 MPa | A |
| None of the above conditions are met | B |
2.4 MPa=24.5 kgf/cm2
2.4 MPa=348 psi
3.2 MPa=32.6 kgf/cm2
3.2 MPa=464 psi
Post-procedure1
None.
A
B
NEXT
for Registration: Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Pre-procedure1
Disconnect the oil pressure sensor connector.
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D47)Location & Routingewd_type=routing;type=c;code=D47 Click Connector(D47)Engine Compartment>Engine Wire>Oil Pressure Sensorewd_type=component;type=c;code=D47;pinno=3,1 |
||
| D47-3 (VC) - D47-1 (E2) | Ignition switch ON | 4.75 to 5.25 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
Connect the oil pressure sensor connector.
OK
NG
Pre-procedure1
Disconnect the oil pressure sensor connector.
Disconnect the TCM connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D47,D71)Location & Routingewd_type=routing;type=c,c;code=D47,D71 Click Connector(D47)Engine Compartment>Engine Wire>Oil Pressure Sensorewd_type=component;type=c;code=D47;pinno=2 Click Connector(D71)Engine Compartment>Engine Wire>Transmission Control ECUewd_type=component;type=c;code=D71;pinno=50 |
||
| D47-2 (PTO) or D71-50 (PTO) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Connect the TCM connector.
Connect the oil pressure sensor connector.
OK
NG
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>OIL PRESSURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Start the engine and wait for 5 seconds or more.
Procedure1
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| P084015 is output | B |
Post-procedure1
None.
A
B
NEXT
for Registration: Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Pre-procedure1
Disconnect the oil pressure sensor connector.
Disconnect the TCM connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D47,D71)Location & Routingewd_type=routing;type=c,c;code=D47,D71 Click Connector(D47)Engine Compartment>Engine Wire>Oil Pressure Sensorewd_type=component;type=c;code=D47;pinno=3 Click Connector(D71)Engine Compartment>Engine Wire>Transmission Control ECUewd_type=component;type=c;code=D71;pinno=49 |
||
| D47-3 (VC) or D71-49 (VCPT) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Connect the TCM connector.
Connect the oil pressure sensor connector.
OK
NG
NEXT
for Registration: Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION