After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the auxiliary battery.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
CHECK POWER DISTRIBUTION BOX ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| *1 | Power Distribution Box Assembly | *2 | Main Body ECU (Multiplex Network Body ECU) |
Reconnect the power distribution box assembly connectors.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| MB-13 (GND1) - Body ground | Ground | Always | Below 1 Ω |
| MB-26 (BECU) - Body ground | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
| MB-27 (IGR) - Body ground | IG power supply | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V |
Install the main body ECU (multiplex network body ECU) to power distribution box assembly.
Click here
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| 4D-5 - Body ground | CXPI communication line | Ignition switch ON | Pulse generation |
| 4E-43 - Body ground | Rear window defogger signal (output) | rear window defogger switch off | Below 1.5 V |
| rear window defogger switch on | 8 to 14 V | ||
| 4B-2 - Body ground*1 | Mirror heater drive signal (output) | Rear defogger switch off | Below 1.5 V |
| Rear defogger switch on | 8 to 14 V | ||
| 4C-10 - Body ground | Power return mirror motor drive signal (output) | Outer rear view mirror assembly moves to the return position | Below 1.5 V |
| Outer rear view mirror assembly not move | 8 to 14 V | ||
| 4C-21 - Body ground | Power retract mirror motor drive signal (output) | Outer rear view mirror assembly moves to the retract position | Below 1.5 V |
| Outer rear view mirror assembly not move | 8 to 14 V | ||
| 4C-24 - Body ground*2 | Rear defogger switch signal (input) | Rear window defogger switch off | Below 1.5 V |
| Rear window defogger switch on | 8 to 14 V |
*1: w/ Mirror Heater
*2: for Manual Air Conditioning System
CHECK SEMICONDUCTOR POWER INTEGRATION ECU
| *a | Component without harness connected
(Semiconductor power integration ECU) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the A85 and A86 semiconductor power integration ECU connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A85-1 (+B) - Body ground | Auxiliary battery power supply | Ignition switch off | 8 to 14 V |
| A86-5 (-S) - Body ground | Headlight ECU sub-assembly operation signal input | Headlight not illuminated | 6 V or higher |
| Headlight illuminated | Below 1.7 V | ||
| A86-16 (GND2) - Body ground | Ground | Always | Below 1 Ω |
| A86-20 (IG) - Body ground | IG power supply | Ignition switch off | Below 1.5 V |
| Ignition switch ON | 8 to 14 V | ||
| A86-24 (-S) - Body ground | Headlight ECU sub-assembly operation signal input | Headlight not illuminated | 6 V or higher |
| Headlight illuminated | Below 1.7 V | ||
| A86-26 (GND1) - Body ground | Ground | Always | Below 1 Ω |
Reconnect the A85 and A86 semiconductor power integration ECU connectors.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A86-8 (CXPI) - Body ground | CXPI communication line | Ignition switch ON | Pulse generation |
| A86-1 (L) - Body ground | Headlight ECU sub-assembly LH operation signal output | Headlight not illuminated | Below 3.0 V |
| Headlight illuminated | 8 V or higher | ||
| A86-2 (L)- Body ground | Headlight ECU sub-assembly RH operation signal output | Headlight not illuminated | Below 3.0 V |
| Headlight illuminated | 8 V or higher | ||
| A86-17 (L) - Body ground | Front fog light RH operation signal output | Front fog light not illuminated | Below 3.0 V |
| Front fog light illuminated | 8 V or higher | ||
| A86-18 (L) - Body ground | Front fog light LH operation signal output | Front fog light not illuminated | Below 3.0 V |
| Front fog light illuminated | 8 V or higher |