Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM › 2020.08–2021.07
RM3700E _59 Vehicle Exterior _093706 DOOR / HATCH _0441751 POWER BACK DOOR SYSTEM J

DOOR / HATCH  POWER BACK DOOR SYSTEM  Power Back Door does not Operate Using Cabin Switch  


DESCRIPTION

The power back door control switch signal is sent to the multiplex network door ECU.

If the power back door does not operate using the power back door control switch, a power back door control switch circuit malfunction is a possible cause.

WIRING DIAGRAM

E270968E19
1.344,1.427 1.802,1.625 0.458,0.198 10 false H132 1.354,1.594 2.927,1.948 1.573,0.354 10 false Power Back Door Control Switch 0.781,2.354 4.448,2.552 3.667,0.198 10 false : CAN Communication Line 5.063,1.979 6.896,2.344 1.833,0.365 10 false Multiplex Network Door ECU 3.125,1.917 3.583,2.115 0.458,0.198 10 false H5 3.115,2.094 4.76,2.448 1.646,0.354 10 false Main Body ECU (Multiplex Network Body ECU) 3.646,1.052 4.323,1.271 0.677,0.219 10 false PBDS 3.396,0.948 3.854,1.146 0.458,0.198 10 false 21 1.313,0.948 1.771,1.146 0.458,0.198 10 false 2 2.896,0.938 3.354,1.135 0.458,0.198 10 false 5 1.49,0.948 1.948,1.146 0.458,0.198 10 false E 2.469,0.958 2.927,1.156 0.458,0.198 10 false CSW

CAUTION / NOTICE / HINT

NOTICE:
·

First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this problem.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU has been performed, initialize the power back door system.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.



PROCEDURE

1.CHECK VEHICLE CONDITION
a.

Check that the power back door function on the multi-information display in the combination meter assembly is set to ON.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>CUSTOMIZE PARAMETERS


Result:
Result Proceed to
Power back door function on the multi-information display in the combination meter assembly is set to ON (power back door system operation is permitted) A
Power back door function on the multi-information display in the combination meter assembly is set to OFF (power back door system operation is prohibited) B



A

2.CHECK POWER BACK DOOR SYSTEM CONDITION

B

SET POWER BACK DOOR FUNCTION TO ON (PERMIT POWER BACK DOOR SYSTEM OPERATION)

2.CHECK POWER BACK DOOR SYSTEM CONDITION
a.

Check the power back door system condition.


Result:
Result Proceed to
The malfunction symptom reproduces A
The malfunction symptom does not reproduce B



A

3.READ VALUE USING GTS

B

3.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Back Door Operation Switch (Instrument) Power back door switch assembly signal OFF or ON OFF: Power back door control switch off
ON: Power back door control switch on
-
Body Electrical > Main Body > Data List
Tester Display
Back Door Operation Switch (Instrument)
50003 449 47
OK:

The power back door control switch functions as specified in the normal condition column.



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

4.INSPECT POWER BACK DOOR CONTROL SWITCH
4.INSPECT POWER BACK DOOR CONTROL SWITCH

OK

5.CHECK HARNESS AND CONNECTOR (POWER BACK DOOR CONTROL SWITCH - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)

NG

REPLACE POWER BACK DOOR CONTROL SWITCH

5.CHECK HARNESS AND CONNECTOR (POWER BACK DOOR CONTROL SWITCH - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)
a.

Disconnect the H132 power back door control switch connector.


b.

Disconnect the H5 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H132,H5)Location & Routing

Click Connector(H132)Instrument Panel>Instrument Panel Wire / Speaker Wire>Power Back Door Control Switch

Click Connector(H5)Instrument Panel>Instrument Panel Wire / Speaker Wire>Main Body ECU

H132-5 (CSW) - H5-21 (PBDS) Always Below 1 Ω
H132-2 (E) - Body ground Always Below 1 Ω
H132-5 (CSW) or H5-21 (PBDS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR