Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB BOLT › 2020.08–2021.07
RM3700E _52 Drivetrain _093736 AXLE AND DIFFERENTIAL _0441809 FRONT AXLE HUB BOLT A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB BOLT  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the front axle hub bolt replacement are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
for HV Model
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Parking support brake system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -




HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION (for HV Model)

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2. DISABLE BRAKE CONTROL (for HV Model)

Hide 3.REMOVE FRONT WHEEL

Hide 4.SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY

a.
C443127

Remove the 2 bolts and separate the front disc brake caliper assembly from the steering knuckle.

NOTICE:

Use wire or an equivalent tool to keep the front disc brake caliper assembly from hanging by the front flexible hose.



Hide 43512 5.REMOVE FRONT DISC

Hide 43502D 6.REMOVE FRONT AXLE HUB BOLT

a.
C443128C01
1.865,1.052 2.698,1.375 2.698,1.375 2.094,0.823 true 2.021,0.26 1.854,0.26 1.854,0.26 1.646,1.094 true 2.74,1.323 3.052,1.521 0.313,0.198 10 false *a 2.042,0.177 2.365,0.344 0.323,0.167 10 true SST 1.74,1.969 1.99,2.135 0.25,0.167 10 false *c 2.906,0.635 3.219,0.833 0.313,0.198 10 false *b
*a Service Nut
*b Hold
*c Turn


Temporarily install 2 service nuts to the front axle hub bolts as shown in the illustration.

Recommended Service Nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)


NOTICE:

Install the service nuts to prevent damage to the front axle hub bolts.



b.

Using SST and a screwdriver or an equivalent tool to hold the front axle hub sub-assembly, remove the front axle hub bolt.

SST
09611-12010  

NOTICE:

Do not damage the threads of the front axle hub bolts.



Hide 43502D 7.INSTALL FRONT AXLE HUB BOLT

a.

Temporarily install a new front axle hub bolt to the front axle hub sub-assembly.


b.
C443129C01
0.938,0.5 1.25,0.302 true 0.865,1.583 0.708,0.865 true 1.865,1.042 2.625,1.375 2.625,1.375 2.104,0.833 true 1.26,0.188 1.448,0.365 0.188,0.177 10 true *a 0.813,1.615 1.125,1.813 0.313,0.198 10 true *b 2.677,1.323 2.885,1.5 0.208,0.177 10 false *a 2.906,0.625 3.094,0.802 0.188,0.177 10 true *c 1.781,1.948 1.969,2.125 0.188,0.177 10 true *d
*a Service Nut
*b Washer
*c Hold
*d Turn


Install a washer and service nut to the front axle hub bolt as shown in the illustration.

Recommended Service Nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)


HINT:

Recommended washer thickness is 5 mm (0.197 in.) or more.



c.

Using a screwdriver or an equivalent tool to hold the front axle hub sub-assembly, install the front axle hub bolt by tightening the service nut.

NOTICE:
·

Install the service nuts to prevent damage to the front axle hub bolts.

·

Do not damage the threads of the front axle hub bolts.




d.

Remove the 3 service nuts and washer from the 3 front axle hub bolts.


Hide 43512 8.INSTALL FRONT DISC

Hide 9.INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY

a.

Install the front disc brake caliper assembly to the steering knuckle with the 2 bolts.

Torque:
107 N*m (1091 kgf*cm, 79 ft.*lbf)

NOTICE:
·

Do not twist the front flexible hose when installing the front disc brake caliper assembly.

·

Make sure that there is no foreign matter on the threads of the bolt.




Hide 10.INSTALL FRONT WHEEL

Hide 11.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (for HV Model)

Hide 12. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL (for HV Model)

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART