Home › Drivetrain › P910 (HYBRID TRANSMISSION / TRANSAXLE) › MOTOR CABLE
RM3700E _52 Drivetrain _093735 P910 HYBRID TRANSMISSION / TRANSAXLE _0441813 MOTOR CABLE A

P910 HYBRID TRANSMISSION / TRANSAXLE  MOTOR CABLE  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C442343N03
1.875,0.823 2.208,0.823 false 2.083,1.406 2.469,1.406 false 2.76,2.104 3.094,2.104 false 6.396,1.49 6.729,1.49 false 6.802,1.333 7.031,1.635 0.229,0.302 18 false 1 2.542,0.646 2.865,0.948 0.323,0.302 18 false 2 2.979,1.208 3.552,1.531 0.573,0.323 18 false 3 3.458,1.938 3.688,2.24 0.229,0.302 18 false 4 1.01,0.427 1.26,0.594 0.25,0.167 10 false x2 1.833,1.906 2.083,2.073 0.25,0.167 10 false x6 2.854,1.271 3.063,1.448 0.208,0.177 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 HYBRID MOTOR CONTROL INVERTER ASSEMBLY G92A0 - - -
2 CONNECTOR COVER 82821T (Click here) - -
3 TERMINAL CAP 82823M (Click here) - -
4 MOTOR CABLE G1148 (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during motor cable removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

CAUTION:
·
A340386

This vehicle has contains high voltage circuits standardized with orange colored wiring and connectors, so follow the instructions in this manual to perform the procedures correctly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·

If the correct procedures are not followed according to the instructions in this manual, there is a danger of electric shock from the high voltage circuits.

·
A340358

Be sure to wear insulating gloves when working on high voltage wiring or components.

·

If work is performed without wearing insulating gloves, there is a danger of electric shock.



HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide G92A0 1.REMOVE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

Hide 82821T 2.REMOVE CONNECTOR COVER

Z101186

CAUTION:

Be sure to wear insulated gloves.



a.
C429080


Hide 82823M 3.REMOVE TERMINAL CAP

Z101186

CAUTION:

Be sure to wear insulated gloves.



a.
C430363


Hide G1148 4.REMOVE MOTOR CABLE

Z101186

CAUTION:

Be sure to wear insulated gloves.


NOTICE:
·

Keep the motor cable terminals and their installation area free from foreign matter, water, etc.

·

Do not touch the waterproof seal or terminals of the motor cable.

·

Cover the hole where the motor cable was installed with tape or equivalent (non-residue type) to prevent entry of foreign matter.




a.
C442344C01
2.781,2.646 3.156,2.5 true 2.563,2.573 2.781,2.74 0.219,0.167 10 false *a 0.406,0.073 0.583,0.365 0.177,0.292 18 false i
*a Waterproof Seal - -


i.

Using an insulated tool, remove the 6 bolts and motor cable from the hybrid vehicle transaxle assembly.