Home › Suspension › FRONT SUSPENSION › FRONT LOWER SUSPENSION ARM › 2020.08–2021.07
RM3700E _53 Suspension _093737 FRONT SUSPENSION _0441836 FRONT LOWER SUSPENSION ARM A

FRONT SUSPENSION  FRONT LOWER SUSPENSION ARM  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C443087N02
5.156,3.125 5.49,3.125 false 1.021,2.656 1.354,2.656 false 4.656,1.594 5.125,1.594 false 5.448,1.458 6.063,1.771 0.615,0.313 18 false 3 4.969,2.99 5.385,3.24 0.417,0.25 18 false 1 4.76,2.583 5.26,2.896 0.5,0.313 10 false x2 2.156,3.24 2.719,3.5 0.563,0.26 10 false x4 2.677,3.135 3.177,3.396 0.5,0.26 10 false x9 0.823,2.49 1.24,2.74 0.417,0.25 18 false 2 1.5,3.125 2.063,3.385 0.563,0.26 10 false x4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FRONT WHEEL - - - -
2 NO. 1 ENGINE UNDER COVER ASSEMBLY 51410 - - -
3 FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY 48069 (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front lower No. 1 suspension arm sub-assembly LH removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Front wheel alignment adjustment for HV Model:
1.

Perform "Reset Memory"

2.

Perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
for Gasoline Model:
Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 51410 2.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 48069 3.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

a.
C444451N01
0.375,0.083 0.656,0.438 0.281,0.354 18 false i 4.271,0.094 4.458,0.385 0.188,0.292 18 true ii

i.

Remove the bolt and 2 nuts and separate the front lower No. 1 suspension arm sub-assembly from the front lower ball joint assembly.


ii.

Remove the 2 bolts, nut and front lower No. 1 suspension arm sub-assembly from the front suspension crossmember sub-assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.