Home › Suspension › REAR SUSPENSION › REAR UPPER ARM › 2020.08–2021.07
RM3700E _53 Suspension _093739 REAR SUSPENSION _0441858 REAR UPPER ARM A

REAR SUSPENSION  REAR UPPER ARM  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C449209N01
0.073,1.156 1.844,2.313 1.771,1.156 1.26,4.615 1.448,4.615 1.448,4.615 2.708,4.073 false 6.125,2.688 6.365,2.25 6.365,2.25 6.542,2.25 false 1.135,2.156 0.813,2.156 false 1.885,2.906 2.052,2.906 2.052,2.906 2.344,2.333 false 1.698,2.75 1.979,3.104 0.281,0.354 18 false 4 0.615,1.99 0.896,2.344 0.281,0.354 18 false 3 1.052,4.438 1.323,4.75 0.271,0.313 18 false 2 6.583,2.115 6.854,2.469 0.271,0.354 18 false 1 0.375,1.573 0.656,1.927 0.281,0.354 10 false x3 0.104,1.188 0.385,1.542 0.281,0.354 12 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR WHEEL - - - -
2 REAR STABILIZER LINK ASSEMBLY 48830 (Click here) - -
3 NO. 2 PARKING BRAKE WIRE ASSEMBLY 890C0A - - -
4 REAR UPPER CONTROL ARM ASSEMBLY 48790 (Click here) - -

*A for LH Side - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear upper control arm assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Rear wheel alignment adjustment
1.

Perform "Reset Memory"

2.

Perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (Click here)

CAUTION:
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 48830 2.REMOVE REAR STABILIZER LINK ASSEMBLY

Z101186

Click here(Click here)

Hide 890C0A 3.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY (for LH Side)

a.
C443658


Hide 48790 4.REMOVE REAR UPPER CONTROL ARM ASSEMBLY

a.
C443657N01
0.885,0.052 1.083,0.333 0.198,0.281 18 true i 4.198,0.052 4.406,0.323 0.208,0.271 18 true ii

i.

Remove the bolt, nut and rear upper control arm assembly from the rear No. 1 suspension arm assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



ii.

Remove the bolt, nut and rear upper control arm assembly from the rear suspension member sub-assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.