Home › Engine / Hybrid System › M15A-FKS (ENGINE CONTROL) › CAMSHAFT OIL CONTROL VALVE (for Intake Side)
RM3700E _51 Engine / Hybrid System _093766 M15A-FKS ENGINE CONTROL _0442015 CAMSHAFT OIL CONTROL VALVE(for Intake Side) A

M15A-FKS ENGINE CONTROL  CAMSHAFT OIL CONTROL VALVE(for Intake Side)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
A472748N02
2.292,0.833 3.031,1 0.74,0.167 0.656,3.833 1.073,3.833 false 1.542,1.99 1.958,1.99 false 3.042,0.906 3.125,0.906 3.125,0.906 3.302,1.594 false 6.354,0.281 6.771,0.281 false 0.469,3.677 0.792,4.031 0.323,0.354 18 false 4 1.375,1.854 1.656,2.208 0.281,0.354 18 false 2 2.104,0.792 2.385,1.146 0.281,0.354 18 false 1 6.125,0.146 6.406,0.5 0.281,0.354 18 false 3 1.281,3.208 1.563,3.563 0.281,0.354 10 false x2 2.365,0.844 3.229,1.229 0.865,0.385 8 false 95 (969, 70)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 CAMSHAFT TIMING GEAR BOLT 135A0 (Click here) - -
2 CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side) 15370 - - -
3 INSPECT FOR ENGINE OIL LEAK - (Click here) - -
4 ENGINE UNDER COVER RH 51441C - - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque
V100135

Engine Oil

PROCEDURE

Hide 135A0 1.INSTALL CAMSHAFT TIMING GEAR BOLT

Z101186

NOTICE:
·

If the camshaft timing gear bolt has been struck or dropped, replace it.

·

If there is any abnormal resistance when temporarily installing the camshaft timing gear bolt, loosen it and make sure that the No. 1 cylinder is at TDC/compression, and then temporarily install the camshaft timing gear bolt again.




a.
A462021N01
1.646,0.146 2.083,0.49 0.438,0.344 18 false i, v 0.5,2.01 0.781,2.365 0.281,0.354 18 false ii 4.052,2.042 4.906,2.396 0.854,0.354 18 true iii, iv, vi

i.

Make sure that the No. 1 cylinder is at the TDC/compression.

HINT:

Check that the cutout of the camshaft timing gear assembly is at the top and align the timing mark (cutout) of the crankshaft pulley with the protrusion on the timing chain cover assembly.



ii.

Apply engine oil to the areas of the camshaft timing gear bolt shown in the illustration.


iii.

While holding the crankshaft pulley, temporarily install the camshaft timing gear bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

If the camshaft timing gear bolt has been struck or dropped, replace it.

·

If there is any abnormal resistance when temporarily installing the camshaft timing gear bolt, loosen it and make sure that the No. 1 cylinder is at TDC/compression, and then temporarily install the camshaft timing gear bolt again.



HINT:

Make sure that the flange part of the camshaft timing gear bolt contacts the entire circumference of the camshaft timing gear assembly.



iv.

While holding the crankshaft pulley, loosen the camshaft timing gear bolt 60 to 180°.


v.

Turn the crankshaft pulley clockwise 30 to 90°.


vi.

While holding the crankshaft pulley, tighten the camshaft timing gear bolt.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)

NOTICE:

Do not use an impact wrench.




Hide 15370 2.INSTALL CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side)

Hide 3.INSPECT FOR ENGINE OIL LEAK

Hide 51441C 4.INSTALL ENGINE UNDER COVER RH