Home › Engine / Hybrid System › M15A-FKS (ENGINE CONTROL) › THROTTLE BODY
RM3700E _51 Engine / Hybrid System _093766 M15A-FKS ENGINE CONTROL _0442019 THROTTLE BODY A

M15A-FKS ENGINE CONTROL  THROTTLE BODY  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A459205N02
4.594,0.417 4.927,0.417 false 4.552,0.813 4.885,0.813 false 6.417,0.292 6.75,0.292 false 2.625,1.552 2.958,1.552 false 2.26,0.917 2.594,0.917 false 2.823,0.396 2.99,0.396 2.99,0.396 3.083,0.813 false 4.75,2.594 5.083,2.594 false 3.677,1.24 4.01,1.24 false 6.229,0.104 6.51,0.458 0.281,0.354 18 false 2 5,0.26 5.281,0.615 0.281,0.354 18 false 3 4.969,0.656 5.25,1.01 0.281,0.354 18 false 4 4.104,1.104 4.385,1.458 0.281,0.354 18 false 5 2.438,1.375 2.719,1.729 0.281,0.354 18 false 6 2.646,0.229 2.927,0.583 0.281,0.354 18 false 7 2.052,0.802 2.292,1.052 0.24,0.25 10 false ● 3.49,0.719 3.729,0.906 0.24,0.188 10 false x3 5.146,2.438 5.427,2.792 0.281,0.354 18 false 1 3.323,3.271 3.563,3.458 0.24,0.188 10 false x4 4.073,3.458 4.313,3.646 0.24,0.188 10 false x4 4.677,3.24 4.917,3.427 0.24,0.188 10 false x9

Procedure Part Name Code
Z101186

Z101188

Z101187

1 NO. 1 ENGINE UNDER COVER ASSEMBLY 51410 - - -
2 DRAIN ENGINE COOLANT - - (Click here) -
3 NO. 2 VENTILATION HOSE 12262 - - -
4 NO. 1 AIR CLEANER HOSE 17881 - - -
5 NO. 5 WATER BY-PASS HOSE 16282 - - -
6 NO. 8 WATER BY-PASS HOSE 16296 - - -
7 THROTTLE BODY WITH MOTOR ASSEMBLY 22030 (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during throttle body with motor assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not performed Link
·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

PROCEDURE

Hide 51410 1.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 2.DRAIN ENGINE COOLANT

Hide 12262 3.DISCONNECT NO. 2 VENTILATION HOSE

a.
A458036


Hide 17881 4.REMOVE NO. 1 AIR CLEANER HOSE

a.
A458037


Hide 16282 5.DISCONNECT NO. 5 WATER BY-PASS HOSE

a.
A458039


Hide 16296 6.DISCONNECT NO. 8 WATER BY-PASS HOSE

a.
A458038


Hide 22030 7.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

a.
A458778N01
0.521,0.115 0.76,0.417 0.24,0.302 18 true iii 4.448,0.135 4.823,0.417 0.375,0.281 18 true i, ii

i.

Disconnect the throttle body with motor assembly connector.


ii.

Using an 8 mm socket wrench, remove the 3 bolts to separate the throttle body with motor assembly from the intake manifold.

NOTICE:

If the throttle body with motor assembly has been struck or dropped, replace it.



iii.

Remove the throttle body gasket from the intake manifold.