Home › Engine / Hybrid System › M15A-FKS (ENGINE CONTROL) › AIR FUEL RATIO SENSOR (for Sensor 1) › 2020.08–2021.07
RM3700E _51 Engine / Hybrid System _093766 M15A-FKS ENGINE CONTROL _0442028 AIR FUEL RATIO SENSOR(for Sensor 1) A

M15A-FKS ENGINE CONTROL  AIR FUEL RATIO SENSOR(for Sensor 1)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A476286N02
3.417,1.5 3.75,1.5 false 2.958,2.094 3.292,2.094 false 2.75,1.083 3.083,1.083 false 1.479,0.417 1.813,0.417 false 5.469,1.833 5.635,1.75 5.635,1.75 5.802,1.75 false 1.885,0.25 2.167,0.604 0.281,0.354 18 false 1 3.167,0.979 3.448,1.333 0.281,0.354 18 false 3 3.833,1.375 4.115,1.729 0.281,0.354 18 false 2 3.438,1.958 3.719,2.313 0.281,0.354 18 false 4 6.188,1.583 6.469,1.938 0.281,0.354 18 false 5 1.385,1.083 1.667,1.438 0.281,0.354 10 false x12

Procedure Part Name Code
Z101186

Z101188

Z101187

1 WINDSHIELD WIPER MOTOR AND LINK - - - -
2 WATER GUARD PLATE LH 55735A - - -
3 NO. 1 FRONT VENTILATOR SEAL 55815E - - -
4 OUTER COWL TOP PANEL SUB-ASSEMBLY 55701J - - -
5 AIR FUEL RATIO SENSOR 89467B (Click here) - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the air fuel ratio sensor removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
·

Replacement of air fuel ratio sensor (sensor 1)

·

Gas leak from exhaust system is repaired


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A344783

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust manifold.

·

Touching high-temperature areas such as the engine and exhaust manifold could result in burns.



PROCEDURE

Hide 1.REMOVE WINDSHIELD WIPER MOTOR AND LINK

Hide 55735A 2.REMOVE WATER GUARD PLATE LH

Hide 55815E 3.REMOVE NO. 1 FRONT VENTILATOR SEAL

Hide 55701J 4.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 89467B 5.REMOVE AIR FUEL RATIO SENSOR

a.
A458737N01
2.896,1.313 3.24,0.99 true 0.49,0.115 3.24,0.469 2.75,0.354 18 false i, ii, iii 2.74,1.323 3.031,1.521 0.292,0.198 10 true SST

i.

Disconnect the air fuel ratio sensor connector.


ii.

Disengage the 2 clamps.


iii.

Using SST, remove the air fuel ratio sensor from the exhaust manifold.

SST
09224-00012  

NOTICE:

If the air fuel ratio sensor has been struck or dropped, replace it.