Home › Engine / Hybrid System › M15A-FKS (ENGINE CONTROL) › AIR FUEL RATIO SENSOR (for Sensor 2) › 2020.08–2021.07
RM3700E _51 Engine / Hybrid System _093766 M15A-FKS ENGINE CONTROL _0442029 AIR FUEL RATIO SENSOR(for Sensor 2) A

M15A-FKS ENGINE CONTROL  AIR FUEL RATIO SENSOR(for Sensor 2)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A479406N01
3.813,0.5 4.292,0.5 false 4.354,0.354 4.635,0.708 0.281,0.354 18 false 1 4.313,1.073 4.625,1.271 0.313,0.198 10 false x2 3.063,1.146 3.375,1.344 0.313,0.198 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 CENTER NO. 4 ENGINE UNDER COVER 51447D - - -

A459214N02
1.156,0.208 5.854,3.125 4.698,2.917 1.146,3.333 5.865,5.656 4.719,2.323 4.063,2.688 4.073,2.385 false 4.573,1.865 4.792,1.677 4.792,1.677 4.927,1.677 false 3.823,5.302 4.229,5.302 false 4.667,4.927 4.531,4.406 4.531,4.406 4.396,4.406 false 1.219,0.292 1.594,0.531 0.375,0.24 12 false *A 1.219,3.396 1.594,3.635 0.375,0.24 12 false *B 5.302,1.552 5.667,1.865 0.365,0.313 18 false 3 4.01,2.76 4.375,3.073 0.365,0.313 18 false 2 4.167,4.26 4.531,4.573 0.365,0.313 18 false 3 3.604,5.135 3.969,5.448 0.365,0.313 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

2 WIRE HARNESS CLAMP BRACKET - - - -
3 NO. 2 AIR FUEL RATIO SENSOR 89467C (Click here) - -

*A for 2WD *B for AWD

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the No. 2 air fuel ratio sensor removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
·

Replacement of air fuel ratio sensor (sensor 2)

·

Gas leak from exhaust system is repaired


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A344784

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.

·

Touching high-temperature areas such as the engine and exhaust pipe could result in burns.



PROCEDURE

Hide 51447D 1.REMOVE CENTER NO. 4 ENGINE UNDER COVER

Hide 2.REMOVE WIRE HARNESS CLAMP BRACKET

a.
A485879C01
0.167,0.052 0.479,0.313 0.313,0.26 12 false *A 3.646,0.052 3.958,0.292 0.313,0.24 12 false *B
*A for 2WD *B for AWD



Hide 89467C 3.REMOVE NO. 2 AIR FUEL RATIO SENSOR

a.

for 2WD:

A458740N01
6,0.885 5.656,0.531 true 0.49,0.094 0.875,0.396 0.385,0.302 18 true i, ii 4.344,0.083 4.729,0.385 0.385,0.302 18 true iii 5.865,0.885 6.188,1.052 0.323,0.167 10 true SST

i.

Disconnect the No. 2 air fuel ratio sensor connector.


ii.

Disengage the 2 wire harness clamps.


iii.

Using SST, remove the No. 2 air fuel ratio sensor from the front exhaust pipe assembly.

SST
09224-00012  

NOTICE:

If the No. 2 air fuel ratio sensor has been struck or dropped, replace it.




b.

for AWD:

A485880N01
6.271,0.177 5.927,0.344 true 0.031,0.031 0.417,0.333 0.385,0.302 18 true i, ii 3.823,0.031 4.208,0.333 0.385,0.302 18 true iii 6.313,0.115 6.635,0.281 0.323,0.167 10 true SST

i.

Disconnect the No. 2 air fuel ratio sensor connector.


ii.

Disengage the 3 wire harness clamps.


iii.

Using SST, remove the No. 2 air fuel ratio sensor from the front exhaust pipe assembly.

SST
09224-00012  

NOTICE:

If the No. 2 air fuel ratio sensor has been struck or dropped, replace it.