Home › Engine / Hybrid System › M15A-FXE (ENGINE CONTROL) › THROTTLE BODY
RM3700E _51 Engine / Hybrid System _093768 M15A-FXE ENGINE CONTROL _0442035 THROTTLE BODY A

M15A-FXE ENGINE CONTROL  THROTTLE BODY  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A459223N01
5.083,3.396 5.417,3.396 false 2.865,1.063 3.031,1.063 3.031,1.063 3.135,1.458 false 6.365,0.333 6.698,0.333 false 4.656,0.458 4.99,0.458 false 4.563,1.365 4.896,1.365 false 3.865,1.813 4.198,1.813 false 3.146,2.167 3.479,2.167 false 2.406,1.875 2.74,1.875 false 6.156,0.156 6.438,0.51 0.281,0.354 18 false 2 5.073,0.333 5.354,0.688 0.281,0.354 18 false 3 4.958,1.198 5.24,1.552 0.281,0.354 18 false 4 4.302,1.688 4.583,2.042 0.281,0.354 18 false 5 3.563,2.021 3.844,2.375 0.281,0.354 18 false 6 2.667,0.958 2.948,1.313 0.281,0.354 18 false 7 2.24,1.792 2.448,2 0.208,0.208 10 false ● 5.51,3.26 5.792,3.615 0.281,0.354 18 false 1 3.26,1.156 3.469,1.365 0.208,0.208 10 false x3 3.302,4.156 3.51,4.365 0.208,0.208 10 false x4 4.219,4.344 4.427,4.552 0.208,0.208 10 false x4 5,4.135 5.208,4.344 0.208,0.208 10 false x9

Procedure Part Name Code
Z101186

Z101188

Z101187

1 NO. 1 ENGINE UNDER COVER ASSEMBLY 51451A - - -
2 DRAIN ENGINE COOLANT - - (Click here) -
3 NO. 2 VENTILATION HOSE 12262 - - -
4 NO. 1 AIR CLEANER HOSE 17881 - - -
5 NO. 5 WATER BY-PASS HOSE 16282 - - -
6 NO. 8 WATER BY-PASS HOSE 16296 - - -
7 THROTTLE BODY WITH MOTOR ASSEMBLY 22030 (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the throttle body with motor assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 51410 1.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 12262 3.REMOVE NO. 2 VENTILATION HOSE

a.
A458714


Hide 17881 4.REMOVE NO. 1 AIR CLEANER HOSE

a.
A458715


Hide 16282 5.REMOVE NO. 5 WATER BY-PASS HOSE

a.
A458717


Hide 16296 6.REMOVE NO. 8 WATER BY-PASS HOSE

a.
A458716


Hide 22030 7.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

a.
A458719N01
4.479,0.156 4.885,0.448 0.406,0.292 18 true i, ii 0.531,0.083 0.854,0.396 0.323,0.313 18 true iii

i.

Disconnect the throttle body with motor assembly connector.


ii.

Using an 8 mm socket wrench, remove the 3 bolts to separate the throttle body with motor assembly from the intake manifold.

NOTICE:

If the throttle body with motor assembly has been struck or dropped, replace it.



iii.

Remove the throttle body gasket from the intake manifold.