Home › Engine / Hybrid System › M15A-FXE (INTAKE / EXHAUST) › INTAKE MANIFOLD
RM3700E _51 Engine / Hybrid System _093770 M15A-FXE INTAKE / EXHAUST _0442057 INTAKE MANIFOLD A

M15A-FXE INTAKE / EXHAUST  INTAKE MANIFOLD  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A460604N01
6.25,3.25 6.583,3.25 false 4.042,4.719 4.042,4.385 false 5.219,4.615 5.552,4.615 false 0.927,2.5 1.427,2.5 false 2.198,1 2.531,1 false 2.438,1.531 2.771,1.531 false 1.25,5 1.635,5 false 5.75,2.333 5.833,2.083 5.833,2.083 6,2.083 false 3.75,3.5 3.917,3.5 3.917,3.5 4,3.021 false 1.979,2.167 2.479,2.167 false 2.302,2.281 2.302,2.167 false 6.646,3.115 6.927,3.469 0.281,0.354 18 false 1 3.969,4.719 4.25,5.073 0.281,0.354 18 false 2 5.625,4.479 5.906,4.833 0.281,0.354 18 false 3 0.719,2.375 1,2.729 0.281,0.354 18 false 4 1.969,0.854 2.25,1.208 0.281,0.354 18 false 5 1.031,4.875 1.313,5.229 0.281,0.354 18 false 6 3.521,3.354 3.802,3.708 0.281,0.354 18 false 7 6.292,1.938 6.573,2.292 0.281,0.354 18 false 8 6.073,2.01 6.229,2.208 0.156,0.198 10 false ● 2.198,1.396 2.479,1.75 0.281,0.354 18 false 9 3.927,0.625 4.24,0.823 0.313,0.198 10 false x2 4.146,0.75 4.458,0.948 0.313,0.198 10 false x2 4.854,1.427 5.167,1.625 0.313,0.198 10 false x3 1.219,1.844 1.531,2.042 0.313,0.198 10 false x4 2.594,2.094 2.75,2.292 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 THROTTLE BODY WITH MOTOR ASSEMBLY 22030 - - -
2 PURGE VALVE (PURGE VSV) 25860 - - -
3 NO. 1 FUEL VAPOR FEED HOSE 23826 - - -
4 NO. 1 EGR PIPE SUB-ASSEMBLY 25601 (Click here) - -
5 E.F.I. VACUUM SENSOR ASSEMBLY (MANIFOLD ABSOLUTE PRESSURE SENSOR) 89421 - - -
6 ENGINE WIRE 82121 - - -
7 INTAKE MANIFOLD 17111 (Click here) - -
8 NO. 1 INTAKE MANIFOLD TO HEAD GASKET 17177 - - -
9 VACUUM HOSE - - - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during intake manifold removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Cleaning the deposits from the throttle body with motor assembly Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 22030 1.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 25860 2.REMOVE PURGE VALVE (PURGE VSV)

Hide 23826 3.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE

a.
A460598


Hide 25601 4.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

a.
A461360N02
0.583,0.479 0.792,0.781 0.208,0.302 18 false i 3.99,0.469 4.198,0.771 0.208,0.302 18 false ii 0.521,2.844 0.781,3.156 0.26,0.313 18 false iii 3.917,2.813 4.177,3.125 0.26,0.313 18 false iv 3.948,3.729 4.208,4.042 0.26,0.313 18 false v

i.

Disconnect the EGR valve assembly connector.


ii.

Disengage the clamp to disconnect the engine wire.


iii.

Using an 8 mm socket wrench, remove the 4 bolts and No. 1 EGR pipe sub-assembly from the intake manifold and EGR valve assembly.


iv.

Remove the EGR valve adapter gasket from the No. 1 EGR pipe sub-assembly.


v.

Remove the EGR inlet gasket from the intake manifold.



Hide 89421 5.REMOVE E.F.I. VACUUM SENSOR ASSEMBLY (MANIFOLD ABSOLUTE PRESSURE SENSOR)

Hide 82121 6.DISCONNECT ENGINE WIRE

a.
A460600


Hide 17111 7.REMOVE INTAKE MANIFOLD

a.
A460601N01
0.625,0.094 0.906,0.448 0.281,0.354 18 false i 4.052,0.094 4.333,0.354 0.281,0.26 18 true ii

i.

Remove the 4 bolts and 2 nuts.


ii.

Using an E8 "TORX" socket wrench, remove the 2 stud bolts, No. 2 fuel delivery guard and intake manifold from the cylinder head sub-assembly.



Hide 17177 8.REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET

a.
A460602


Hide 9.REMOVE VACUUM HOSE

a.
A460603